ملخص المحتوى في الصفحة رقم 1
Operator′s manual
327LD
X-series
Please read the operator’s manual carefully and make sure you understand the instructions
before using the machine.
E En ng glliis sh h
E En ng glliis sh h
ملخص المحتوى في الصفحة رقم 2
15 m 50FT KEY TO SYMBOLS Symbols WARNING! Clearing saws, Wear sturdy, non-slip boots. brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the Only use non-metallic, flexible operator’s manual. cutting attachments, i.e. trimmer heads with trimmer cord. Please read the operator’s manual carefully and make sure you
ملخص المحتوى في الصفحة رقم 3
CONTENTS Contents Note the following before KEY TO SYMBOLS starting: Symbols ................................................................ 2 Please read the operator’s manual carefully. CONTENTS Contents ............................................................... 3 WARNING! Long-term exposure to noise can result in permanent hearing Note the following before starting: ........................ 3 ! impairment. So always use appr
ملخص المحتوى في الصفحة رقم 4
INTRODUCTION Dear Customer, Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water- powered plant. During the more than 300 years of beeing, the Husqvarna factory has produced a lot
ملخص المحتوى في الصفحة رقم 5
WHAT IS WHAT? 3 1 2 7 6 8 10 4 13 12 5 11 14 1 19 18 9 17 21 16 20 15 22 4 23 24 What is what? 1 Trimmer head 13 Cylinder cover 2 Grease filler cap, bevel gear 14 Starter handle 3 Bevel gear 15 Fuel tank 4 Cutting attachment guard 16 Air filter cover 5 Shaft 17 Air purge 6 Shaft coupling 18 Choke control 7 Loop handle 19 Handle adjustment 8 Suspension ring 20 Drive disc 9 Throttle control 21 Operator′s manual 10 Stop switch 22 Allen key 11 Throttle lockout 23 Locking pin 12 Spark plug
ملخص المحتوى في الصفحة رقم 6
GENERAL SAFETY PRECAUTIONS Important Personal protective equipment IMPORTANT! IMPORTANT! The machine is only designed for trimming grass. A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can The only accessories you can operate with this engine cause serious or fatal injury to the operator or others. It unit are the cutting attachments we recommend in the is extremely important that you read and understand the chapter on Te
ملخص المحتوى في الصفحة رقم 7
GENERAL SAFETY PRECAUTIONS BOOTS original positions. This movement is controlled by two independent return springs. This arrangement means that Wear sturdy, non-slip boots. the throttle control is automatically locked at the idle setting. A CLOTHING B Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts Make sure the throttle control is locked at the idle sett
ملخص المحتوى في الصفحة رقم 8
GENERAL SAFETY PRECAUTIONS Use of incorrectly wound cord or an incorrect cutting Stop switch attachment increases the level of vibration. See Use the stop switch to switch off the engine. instructions under the heading Cutting equipment. The machine′s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machine′s handle unit. Start the engine and make sure the engine stops when Regularly check the vibration damping units
ملخص المحتوى في الصفحة رقم 9
GENERAL SAFETY PRECAUTIONS Never use a machine that has a faulty muffler. • Extend the life of cutting equipment. IMPORTANT! Only use cutting attachments with the guards we recommend! See the chapter on Technical data. Refer to the instructions for the cutting attachment to check the correct way to load the cord and the correct cord diameter. Regularly check that the muffler is securely attached to the machine. WARNING! Always stop the engine before doing any work on the cutting ! attachment
ملخص المحتوى في الصفحة رقم 10
ASSEMBLY • Before using the unit, tighten the knob securely. Fitting the loop handle • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. Dismantling: • Loosen the coupling by turning the knob (at least 3 times). • Slide the spacer into the slot in the loop handle. Fit the • Push and hold the button (C). While securely holding nut, knob and screw. Do not overtighten. the engine end, pull the attachment straight out of the • Now adju
ملخص المحتوى في الصفحة رقم 11
ASSEMBLY • Screw on the trimmer head/plastic blades (H) in the Assembling the cutting opposite direction to the direction of rotation. equipment H WARNING! ! When fitting the cutting attachment it is H extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of the cutting attachment. If the cutting attachment is fitted incorrectly it can • To dismantle, follow the instructions in the reverse result in serious and/or fatal personal o
ملخص المحتوى في الصفحة رقم 12
FUEL HANDLING Petrol Fuel safety Never start the machine: 1 If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporate. CAUTION! Always use a quality petrol/oil mixture at least 2 If you have spilt fuel on yourself or your clothes, 90 octane (RON). If your machine is equipped with a change your clothes. Wash any part of your body that catalytic converter (see chapter on Technical data) always has come in contact with fuel. Use soap and water. use a good qual
ملخص المحتوى في الصفحة رقم 13
FUEL HANDLING Mixing Fuelling • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of WARNING! Taking the following petrol. precautions, will lessen the risk of fire: ! • Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank. Do not smoke or place hot objects near fuel. Always shut off the engi
ملخص المحتوى في الصفحة رقم 14
STARTING AND STOPPING Check before starting Starting and stopping • Check that the support flange is not cracked due to WARNING! The complete clutch cover fatigue or due to being tightened too much. Discard and shaft must be fitted before the the support flange if it is cracked. ! machine is started, otherwise the clutch can come loose and cause personal injury. Always move the machine away from the refuelling area before starting. Place the machine on a flat surface. Ensure the cutting att
ملخص المحتوى في الصفحة رقم 15
STARTING AND STOPPING apply full throttle; the throttle will automatically disengage from the start setting. CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. CAUTION! Do not put any part of your body in marked area. Contact can result in burns to the skin, or electrical shock if the spark plug cap has been damaged. Always use gloves. Do not use a machine with damaged spark plug cap.
ملخص المحتوى في الصفحة رقم 16
WORKING TECHNIQUES 6 Always hold the machine with both hands. Hold the General working instructions machine on the right side of your body. IMPORTANT! This section takes up the basic safety precautions for working with a trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop. Avoid all usage which you consider to be beyond your capability. You must understand the difference between forestry clearin
ملخص المحتوى في الصفحة رقم 17
WORKING TECHNIQUES Cutting Basic working techniques • The trimmer is ideal for cutting grass that is difficult to Always slow the engine to idle speed after each working reach using a normal lawn mower. Keep the cord operation. Long periods at full throttle without any load on parallel to the ground when cutting. Avoid pressing the the engine can lead to serious engine damage. trimmer head against the ground as this can ruin the lawn and damage the tool. WARNING! Sometimes branches or gras
ملخص المحتوى في الصفحة رقم 18
MAINTENANCE • The T-screw regulates the throttle setting at idle Carburettor speed. If the T-screw is turned clockwise this gives a Your Husqvarna product has been designed and higher idle speed; turning it anti-clockwise gives a manufactured to specifications that reduce harmful lower idle speed. emissions. After the engine has used 8-10 tanks of fuel Basic setting the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhaust • The basic
ملخص المحتوى في الصفحة رقم 19
MAINTENANCE Low speed jet L High speed jet H Try to find the highest idle speed by turning the low speed The high speed jet H affects the engine power, speed, jet L clockwise then anti-clockwise. When the highest temperature and fuel consumption. If the high speed jet H speed has been found, turn the low speed jet L 1/4 turn is set too lean (screwed in too far) the engine speed will anti-clockwise. be too high and cause engine damage. Do not let the engine run at full speed for more than 10 s
ملخص المحتوى في الصفحة رقم 20
MAINTENANCE Muffler Cooling system CAUTION! Some mufflers are fitted with a catalytic To keep the working temperature as low as possible the converter. See chapter on Technical data to see whether machine is equipped with a cooling system. your machine is fitted with a catalytic converter. The muffler is designed to reduce the noise level and to 4 direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and com
