ملخص المحتوى في الصفحة رقم 1
®
18 VOL 18 VOL 18 VOLT CORDLESS T CORDLESS T CORDLESS
18 VOL 18 VOLT CORDLESS T CORDLESS
CHAINSA CHAINSA CHAINSAW W W
CHAINSA CHAINSAW W
44493
ASSEMBLY AND OPERATING INSTRUCTIONS
®
Distributed Exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2000 by Harbor Freight Tools . All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape or
form without
ملخص المحتوى في الصفحة رقم 2
Specifications ITEM DESCRIPTION Cutting Length 4-1/2 inches Chain Speed 520 FPM Chain Type 25 AP Chain Pitch 1/4 inch Weight 5.5 lbs. Overall Length 18-1/2 inches Battery 18 VDC Switches Safety switch and trigger Battery Charger, 6 foot cord, U.L. Listed Accessories Oil Bottle Blade Cover Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Writ
ملخص المحتوى في الصفحة رقم 3
7. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically non-conductive clothes and non-skid footwear are recommended when working. Wear restrictive hair covering to contain long hair. 8. Use eye and ear protection. Always wear ANSI-approved impact safety goggles. Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical
ملخص المحتوى في الصفحة رقم 4
Unpacking When unpacking, check to make sure the following parts are included. Cordless Chainsaw, 18 Volt Battery Pack, Charger, Blade Cover, and Oil Bottle. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Battery Precautions 1. Read all instructions and warnings on the battery before charging the battery. 2. To avoid accidents, charge the supplied battery only. Do not use a different charger with this battery.
ملخص المحتوى في الصفحة رقم 5
Charging Battery The Battery does not come charged from the factory. Charge for 5 to 6 hours before using. 1. Plug the Charger cord into an electrical outlet. 2. Insert the battery (32) into the Charger Base. The battery can only insert one way. Battery (32) Warning: Never charge battery more Charger than 12 hours continuously. Charg- SET Button ers should not be left plugged in, or charg- OFF Light ing for more than 12 ON Light hours. 4. Press the Set button to start the charging The ON ind
ملخص المحتوى في الصفحة رقم 6
Oil Bottle Safety Switch (35) Chain Guide Bar (14) Tip Guard Lock-spring Clasps Battery (32) Chain (15) Rubber Cover (22) Switch Button (29) 3. With your right hand, press down on the Safety Switch (35), then press the Switch Button (29). The Switch Button cannot be squeezed unless the Safety Switch is depressed. With the Chainsaw running, you can let go of the Safety Switch. 4. Begin cutting with a light downward pressure. Allow the saw chain to cut at its own rate. Applying too much pressure c
ملخص المحتوى في الصفحة رقم 7
Parts List Item # Description Item # Description 1 Right Chain Cover 21 Left Case 2 Inner Gear 22 Rubber Cover 3 Epicyclic Gear 23 Motor Cover 4 Spindle 24 Relief 5 Bearing 25 Spring 6Plate 26 Electric Wire 7 Crosshead Self-tapping Screw 27 Motor Support 8 Washer 28 Motor and Gear Assy 9 Sprocket 29 Switch Button 10 Washer, Bore 30 Right Case 11 Locking Ring 31 Hex Key 12 Left Chain Cover 32 Battery 13 Crosshead Self-tapping Screw 33 Connector, Body to Battery 14 Chain Guide Bar 34 Switch 15 Cha
ملخص المحتوى في الصفحة رقم 8
Assembly Drawing SKU 44493 Page 8
