ملخص المحتوى في الصفحة رقم 1
Jeep
®
P Please read this man lease read this manu ual al
a and sa nd sav ve it with y e it with yo our original ur original
s sales receipt. ales receipt.
T Tools needed f ools needed fo or r assemb assemblly y: :
P Phillips Scre hillips Screw wdriver and Saf driver and Safe ety ty
S Scissor cissors s (both not inc (both not incllu uded). ded).
U Use onl se only y with the inc with the incllu uded ded
® ®
P Po ow wer Wheels er Wheels 12 12 V Vo ollt Lead- t Lead-
A Acid,
ملخص المحتوى في الصفحة رقم 2
TABLE OF CONTENTS Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Parts . . . . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 3
ELECTRICAL HAZARD WARNING Battery can fall out and injure a child if vehicle tips over. Always use battery retainer. PREVENT FIRE - Never modify the electrical system. Alterations could cause a fire resulting in serious injury and could also ruin the electrical system. - Use of the wrong type battery or charger could cause a fire or explosion resulting in serious injury. ® ® - Use of Power Wheels components in products other than Power Wheels vehicles could cause overheating, fire
ملخص المحتوى في الصفحة رقم 4
PARTS If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store. Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded. Metal parts have been coated with a lubricant to protect them during shipment. Wipe all metal parts with a paper towel to remove any excess lubricant. Brush Guard Rear Clip Vehicle 2 Rear
ملخص المحتوى في الصفحة رقم 5
Steering Wheel Cap 2 Side Mirrors Steering Wheel (Left and Right) Key Rear Grille 4 Hubcaps Steering Column Rear Axle 2 Taillights 2 Wheel 4 Front Steering Retainers Axle Caps Column Cap 12 Volt Charger 12 Volt Orange Battery Part Not Shown: Label Sheet - 2 3 #8 x /4" Screw - 53 5 1 /32" x 1 /2" Pin - 1 Fasteners Shown Actual Size For your convenience, we included extra fasteners! Note: Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. J4394pr-0921 5
ملخص المحتوى في الصفحة رقم 6
PARTS PICTURE Note: Some parts shown are assembled to both sides of the vehicle. 25 26 15 25 10 18 9 18 14 13 17 23 5 8 11 16 4 1 11 12 6 11 19 12 11 22 21 22 24 20 21 2 7 3 1 Vehicle 9 Seat Bar 17 Steering Column 25 Short Seat Belt - 2 2 Front Grille 10 Rear Grille 18 Taillights - 2 26 Long Seat Belt 3 Brush Guard 11 Fender - 4 19 Wheel Retainer - 2 Parts Not Shown 4 Rear Clip 12 Side Mirror - 2 20 Steering Column Cap 2 Label Sheets 5 Rear Bumper 13 Steering Wheel 21 Front Axle Cap - 4 3 #8
ملخص المحتوى في الصفحة رقم 7
BATTERY CHARGING ELECTRICAL HAZARD About Thermal Fuses ® WARNING Your Power Wheels 12 volt orange battery is equipped with a built-in thermal fuse. The thermal fuse is a self-resetting safety device which Battery can fall out and injure a child if automatically “trips” and shuts down operation of the vehicle if the vehicle is overloaded or the driving conditions too severe. Once vehicle tips over. Always use battery retainer. a fuse has "tripped", remove your foot from the pedal and wait
ملخص المحتوى في الصفحة رقم 8
ASSEMBLY WARNING Children can be harmed by small parts, sharp edges and sharp points in the vehicle's B unassembled state, or by electrical items. Orange Care should be taken in unpacking and Battery assembly of the vehicle. Children should not handle parts, including the battery, or help in assembly of the vehicle. A Charger Connector A Plug the charger connector into the battery . B Plug the charger into a standard wall outlet . Notes: - Use the charger only in a wall out
ملخص المحتوى في الصفحة رقم 9
Motor Harness Connector Rear Clip 4 REAR VIEW Pull the motor harness connector through the opening in the rear clip and into the trunk. 2 Fit the rear clip onto the rear end of the vehicle and over the rear bumper. Make sure the tabs on each side of the rear clip fit into the sides of the vehicle. “Snap” the sides of the rear bumper into the openings on each side of the rear clip. Trunk Lid 5 TOP VIEW Insert two screws into the trunk and tighten. Replace the trunk lid. Rear Grill
ملخص المحتوى في الصفحة رقم 10
Seat Bar Taillights 7 Seat 9 “Snap” both taillights to the rear clip. Fit the seat bar to the back of the seat. Insert four screws through the seat bar and into the seat. Tighten the screws. Short Seat Belt Seat Long Seat Belt 8 Insert the fastener end of a short seat belt strap through the slot near the outer edge of the seat. Make sure the side of the seat belt with the fastener faces the outer edge of the seat. Pull the short seat belt strap completely through the slot until the
ملخص المحتوى في الصفحة رقم 11
TOP VIEW T TOP VIEW OP VIEW 3 3 3 3 3 3 3 3 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 SIDE VIEW 11 Insert four screws through the seat bar and into the vehicle. Tighten the screws. 10 Note: The seat is adjustable and has three positions. You can move the seat back as your child grows. Insert the tabs on the front edge of the seat into one of the sets of slots inside the vehicle. Choose the slots closest to the dash for shorter drivers and the slots furthest from the dash for taller drivers. INSI
ملخص المحتوى في الصفحة رقم 12
4 Front Grille 1 3 Brush Guard 2 13 TOP VIEW 15 Fit the front grille to the grooves in the top of the brush guard, as shown. Fit the four fenders marked 1, 2, 3 and 4, to the vehicle, as shown. Inset three screws through the front grille and into the brush guard. Hint: The fenders are designed to fit the vehicle one way. Tighten the screws. Make sure the peg on the inside edge of each fender fits into the lower hole inside each wheel well. FRONT VIEW 14 16 Fit the front grille assemb
ملخص المحتوى في الصفحة رقم 13
Steering Column Steering Column Cap Steering Column FRONT BOTTOM VIEW 19 INSIDE VIEW 17 Fit the steering column cap onto the end of the steering column. Wipe the steering column with a paper towel to remove any excess lubricant. Insert the curved end of the steering column down through the opening in the dash and then down through the hole in the vehicle floor. Hint: You may need to turn the steering column to fit it through both openings. Steering Linkage Steering Column 20 Insert a s
ملخص المحتوى في الصفحة رقم 14
Front Axle Post Front Axle Cap 23 Wheel Well Fit a front axle cap onto the front axle post and hold it in place. Insert a screw through the large opening in the front axle cap and Fender the hole in the front axle. Tighten the screw. 21 Repeat this procedure to fasten the bottom of the other front axle. Insert a screw through each wheel well and into each fender. Tighten the screws. "Lug Nuts" Front Axle Slot Front Wheel 24 Front Axle 22 Note: There are front and rear wheels. The rear
ملخص المحتوى في الصفحة رقم 15
Front Axle Cap Rear Axle 25 REAR BOTTOM VIEW 27 Fit a front axle cap onto the end of the front axle. Slide the rear axle through the large opening near the rear of the vehicle, as shown. 26 "Lug Nuts" Insert a screw through the large opening in the front axle cap and Rear Wheel the hole in the front axle. Tighten the screw. 28 Repeat this procedure to attach the other front wheel to the other front axle. Place a rear wheel onto the rear axle with the “lug nuts” facing out. Turn th
ملخص المحتوى في الصفحة رقم 16
Wheel Retainer Steering Column Steering Wheel Tab 29 Fit a wheel retainer onto the end of the rear axle. 32 INSIDE VIEW Position the steering wheel so that the tab is upright. Fit the steering wheel onto the end of the steering column. 5 5 1 1 //32 3 32 2" x 1 " x 1 " x 1 //2 2" Pin " " Pin Pin Press Wheel P Press Wheel ress Wheel 30 Insert a screw through the large opening in the wheel retainer and the hole in the rear axle. Tighten the screw. Push the axle into the wheel as far as
ملخص المحتوى في الصفحة رقم 17
Steering Wheel Cap Post Side Mirror Recessed Area 34 Fit the steering wheel cap onto the center of the steering wheel. Insert two screws into the steering wheel cap and tighten. Right Side Mirror SIDE VIEW 36 Position the right side mirror with the recessed area facing up, as shown. “Snap” the right side mirror onto the post on the right side of the vehicle. Turn the mirror upright. 35 Pull up on the steering wheel to be sure it is assembled correctly. If you can remove the steer
ملخص المحتوى في الصفحة رقم 18
1.5V x 4 "C" (LR14) Battery Safety Information In exceptional circumstances batteries may leak fluids that can cause a chemical burn injury or ruin your toy. To avoid battery leakage: Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). Insert batteries as indicated inside the battery compartment. Remove batteries during long periods of non-use. Always remove exhausted batteries from the toy. Dispose of batt
ملخص المحتوى في الصفحة رقم 19
DECORATION Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils. Place the labels exactly as shown in the illustrations. For best results, avoid repositioning a label once it has been applied to the vehicle. After applying a label, rub the label firmly with a clean, dry cloth to make sure the label is adhered to your vehicle. Start at the center of a label, and smooth towards the outer edges to remove air bubbles. 6 19 4 6 12 13 1
ملخص المحتوى في الصفحة رقم 20
15 18 15 15 10 11 2 16 19 9 12 14 17 1 12 BACK VIEW 8 7 SIDE VIEW J4394pr-0921 20
