ملخص المحتوى في الصفحة رقم 1
Infant Seat Toddler Seat
Instructions
Model Number: H5985
WARNING
IMPORTANT! KEEP FOR FUTURE REFERENCE.
Please read these instructions before assembly and use of this product.
Use the upright position only when your child has developed enough upper
body control to sit without leaning forward.
Always use the restraint until your child is able to climb in and out of the chair unassisted.
Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included).
Requires one LR20 (
ملخص المحتوى في الصفحة رقم 2
Parts WARNING IMPORTANT! Please remove all parts from the package and identify them before assembly. The kickstand is packaged within the pad at the factory. Before beginning assembly, To prevent serious injury or death: please remove kickstand from the pad. • It is dangerous to use this product on an elevated surface. • Never use on a soft surface (bed, sofa, cushion) since product can tip over and cause suffocation in soft surfaces. 3 Toys Toy Bar • Always use the restraint until child is ab
ملخص المحتوى في الصفحة رقم 3
Assembly IMPORTANT! Before assembly or each use, inspect this product Seat Back Tube for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing, damaged or broken. Contact Press Tabs Mattel for replacement parts and instructions if needed. Never substitute parts. Side Rail Sockets Cross Brace (Push) Button 3 Side Rails • Insert the seat back tube into the socket in each side rail. • While pressing the tabs on the ends of the seat back tube, 1 continue
ملخص المحتوى في الصفحة رقم 4
Assembly #8 x 2.9 cm Screw Side Rail Press Tab Side Rail Press Tab Front Tube 5 • Insert a #8 x 2.9 cm screw through the outside of each side rail and into the ends of the front tube. IMPORTANT! Please follow the next assembly (step 6) carefully to completely secure the front tube to the side rails. Kickstand Receptacles 7 Retainer with Lock Nut • Position the assembly face down, as shown. • While pressing the tab on each end of the kickstand, insert the kickstand into the receptacle in each sid
ملخص المحتوى في الصفحة رقم 5
Assembly Press Seat Back Pad Pad Slot Seat Back Tube Hardboard Side Rail Pad Buckles 9 • Turn the hardboard over and insert it into the slot in the front edge of the pad. • Fasten the pad buckles on the front edge of the pad and under- neath the seat. Make sure you hear a "snap" on both sides. • Press the fasteners together in the seat back portion of the pad. 8 Pad Buckles • Turn the assembly upright. • Fit the upper pocket on the pad onto the seat back tube. • Fasten the pad buckles around eac
ملخص المحتوى في الصفحة رقم 6
Battery Installation Battery Safety Information Batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage: • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable 1,5V (nickel-cadmium). LR20 (“D”) + – • Insert batteries as indicated inside the battery compartment. • Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. Dispose of ba
ملخص المحتوى في الصفحة رقم 7
Setup and Use IMPORTANT! Before each use, inspect this product for damaged Seat Position hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Lift WARNING To prevent serious injury or death: • Reclined position not recommended for children who can sit up by themselves (6 months approximately, until 9 kg.). Press Button • Use the upright position only when child
ملخص المحتوى في الصفحة رقم 8
Securing Your Infant Anchored End Anchored End WARNING To prevent serious injury or death: • Always use the restraint until child is Free End Free End able to climb in and out of the chair unassisted. Tighten Loosen 3 • It is dangerous to use this product on an elevated surface. To tighten the belts: Feed the anchored end of the restraint belt • Never leave child unattended. up through the buckle to form a loop . Pull the free end of the restraint belt . Repeat this procedure to tighte
ملخص المحتوى في الصفحة رقم 9
Toy Bar Calming Vibrations Toy Bar Plug Power Switch 5 • Make sure your child is properly secured in the seat. Toys • Slide the power switch to the on position for calming vibrations. • Slide the power switch to the O off position to turn vibrations off. Plug Kickstand 4 • Fit the plugs on each end of the toy bar into the sockets in each side rail. • Fit the toy bar straps through the slot in the toy rings. Fasten the straps. • Or, attach the toys to the pad straps. Kickstand 6 • Rotate
ملخص المحتوى في الصفحة رقم 10
Storing the Restraint System for Toddler Use Small Slots Large Slot 8 7 • Insert the restraint belts back through the small slots in the pad. • Turn the rocker face down. • Insert the restraint pad down through the large slot in the pad. • Tuck the ends of the restraint pad underneath the buckles, as shown. 10 10
ملخص المحتوى في الصفحة رقم 11
Care Consumer Information • The pad is machine washable. Wash the pad separately in cold GREAT BRITAIN water on the gentle cycle. Do not use bleach. Line dry. Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500302. • The frame, toy bar and toys may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach. Do AUSTRALIA not use harsh or abrasive cleaners. Rinse clean with water to Mattel Australia Pty. Ltd., 658 Church Street, remove residue. Loc
ملخص المحتوى في الصفحة رقم 12
©2004 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A. PRINTED IN CHINA H5985pr-0726
