ملخص المحتوى في الصفحة رقم 1
CORDLESS
HAMMER DRILLS
STOCK No. 63121 PART No.CDH120V
63122 CDH140V
• INSTRUCTIONS •
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE
SAFE AND EFFECTIVE USE OF THIS TOOL.
08/2000
GENERAL INFORMATION
This manual has been compiled by Draper Tools and is an integrated part of the power tool equipment, which
should be kept with the machine.
This manual describes the purpose for which this tool has been designed and contains all the necessary
information to ensure its correct an
ملخص المحتوى في الصفحة رقم 2
CORDLESS DRILLS STOCK No.63121. PART No.CDH120V. 63122. CDH140V. CONTENTS: Page No. Specification/Guarantee ................................................................................................2 Power Supply .................................................................................................................3 General Safety Instructions for Power Tools ..................................................................4 Added Safety Instructions for Cordless Power Tools
ملخص المحتوى في الصفحة رقم 3
SPECIFICATION Whilst every effort has been made to ensure accuracy of information given in this manual is correct at the time of going to print, the Draper Tools policy of continuous improvement determines the right to change specification without notice. Part No. ............................. CDH120V ................................................................ CDH140V Stock No. ...................... 63121 ............................................................................. 6312
ملخص المحتوى في الصفحة رقم 4
POWER SUPPLY CONNECTING YOUR MACHINE TO THE POWER SUPPLY: (240V) To eliminate the possibility of an electric shock your machine has been fitted with a BS approved, non rewireable moulded plug and cable which incorporates a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced an approved BS1362 fuse must be used of the same rating, marked thus . The fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover is
ملخص المحتوى في الصفحة رقم 5
GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS WARNING Please read the following instructions carefully, failure to do so could lead to serious personal injury. IMPORTANT Draper Tools Limited recommends that this machine should not be modified or used for any application other than that for which it was designed. If you are unsure of its relative applications do not hesitate to contact us in writing and we will advise you. 1. KNOW YOUR POWER TOOL 15. DISCONNECT POWER TO THE TOOL Read and understand
ملخص المحتوى في الصفحة رقم 6
ADDED SAFETY INSTRUCTIONS FOR CORDLESS POWER TOOLS Safety is a combination of operator common sense and alertness at all times when the drill is being used. WARNING For your own safety do not attempt to use your drill until the battery is fully charged. Remember the drill is always in an operating condition as it does not need to be connected to a power supply.When not in use place the direction of rotation switch in the neutral position. Before drilling check that there are no hidden hazards su
ملخص المحتوى في الصفحة رقم 7
UNPACKING AND CHECKING CONTENTS WARNING: For your own safety, never connect the plug to the power supply until all the assembly steps have been completed and you have read and understood the safety and operating instructions. FIG.A ✕✌ Cordless hammer drill. ✖✌ Battery charger complete with BS approved moulded plug and cable. ✗✌ Battery pack. ✘✌ Carrying case. FIG.A ✘✌ ✕✌ ✗✌ ✖✌ Carefully unpack the storage case and its contents from the carton. Place the storage box on a flat level surface. Now o
ملخص المحتوى في الصفحة رقم 8
GETTING TO KNOW YOUR CORDLESS DRILL/CHARGER ✮✌ ✴✌ ✱✌ ✬✌ ✭✌ ✫✌ ✪✌ ✲✌ ✳✌ ✯✌ ✰✌ FIG.B ✪✌ TRIGGER - When the variable speed switch trigger is depressed the chuck will rotate (providing the direction switch is in a clockwise or anticlockwise position). ✫✌ FORWARD/REVERSE LEVER - This lever determines the direction of rotation of the chuck, i.e. clockwise or anticlockwise. ✬✌ KEYLESS CHUCK - This is for holding tools, i.e. drill bits or screwdriver bits. ✭✌ RATING PLATE - Shows Part No., voltage, capa
ملخص المحتوى في الصفحة رقم 9
OPERATION AND USE BATTERY CHARGING Fig.1. To charge the battery pack it must first be removed from the drill. To release the battery pack squeeze the grips located on either side of the battery casing and gently pull the battery pack from the housing (fig.1). Plug the battery charger unit into a 13 amp, three-pin socket. Place the battery in the charger as shown in (fig.2). Making sure the + and - on the battery line up with the + and - on the charger (+ T0 +, - T0 -). Do not force. Ensure the b
ملخص المحتوى في الصفحة رقم 10
OPERATION AND USE CHANGING SPEEDS Fig.6. ✫✌ To change the speed of the chuck, push the two-speed gearbox selection switch ✫✌ ,(fig.6 and 7) forwards for low speed, or backwards for high speed. IMPORTANT: ONLY CHANGE SPEED WHEN THE MACHINE IS STOPPED. TRIGGER When the trigger is depressed the chuck will rotate (provided the direction switch is set in Fig.7. the forward or reverse position). This trigger ✫✌ switch is electronic which enables the user to vary the speed continuously in both gears. T
ملخص المحتوى في الصفحة رقم 11
OPERATION AND USE DRILLING WOOD AND PLASTIC To prevent splitting around the drill holes on the reverse side, place a piece of scrap timber under the material to be drilled. DRILLING MASONRY Start drilling at a low speed to prevent the drill bit from wandering. Once penetration is achieved fully depress the trigger to achieve maximum speed and hammer power. DRILLING METAL Metals such as sheet steel, aluminium and brass may be drilled. Mark the point to be drilled with a punch or nail to help the
ملخص المحتوى في الصفحة رقم 12
DRAPER TOOLS LIMITED, Hursley Road, Chandler's Ford, Eastleigh, Hants. SO53 1YF. U.K. Helpline: (023) 8049 4344. Sales Desk: (023) 8049 4333. General Enquiries: (023) 8026 6355. Fax: (023) 8026 0784. www.draper.co.uk e-mail: sales@draper.co.uk YOUR DRAPER STOCKIST ©Published by Draper Tools Ltd. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without prior permissio
