ملخص المحتوى في الصفحة رقم 1
GB6MP-10-LD-U
GB5MV-10-LD
GB8MP-10-LD-U
Operation Manual
NL48P July 2005
ملخص المحتوى في الصفحة رقم 2
CONTENTS Important Owner Information_____________________________________1 Introduction____________________________________________________1 Important Safety Instructions___________________________________2 Model Description_______________________________________________3 Specifications__________________________________________________3 Plug Configurations_____________________________________________3 Installation____________________________________________________4
ملخص المحتوى في الصفحة رقم 3
IMPORTANT OWNER INFORMATION Record the model number, serial number (identification plate is located behind front door), voltage and purchase date of your Cecilware Cappuccino Dispenser in the spaces below. Please have the information available when calling Cecilware for assistance. Model #: Serial #: Voltage: Date of Purchase: Business 8:30 a.m. to 5:00 p.m. Hours: Eastern Standard Time Telephone: 800-935-2211; 718-932-1414 Fax: 718-
ملخص المحتوى في الصفحة رقم 4
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT! Read the following important safety instructions to avoid personal injury or death, and to avoid damage to the equipment or property. WARNINGS The GB8MP-10-LD-U (only) is equipped with two (2) power switches and two (2) 120 volt grounded power cords. To avoid any injury, turn both power switches OFF. Or, unplug both power cords and allow unit to cool completely before performing any maintenance or cleaning. The GB5MV-
ملخص المحتوى في الصفحة رقم 5
MODEL DESCRIPTION GB8MP-10-LD-U (shown) GB5-LD-U & GB6MP-10-LD-U (typical) These High Volume Cappuccino Dispensers will hold double the amount of your most popular flavor along with up to seven other flavors as well. With these Dispensers you will not waste valuable time refilling product Hoppers or lose profits during peak sales periods. With the hot water dispense button, you can
ملخص المحتوى في الصفحة رقم 6
UNPACKING INSTRUCTIONS Carefully unpack the Cappuccino Dispenser Unit and inspect immediately for shipping damage. Your Cappuccino Dispenser Unit was shipped in a carton designed to give it maximum protection in normal handling. It was thoroughly inspected before leaving the factory. In case of damage, contact the shipper. DESCRIPTION AND LOCATION OF COMPONENTS Note: Refer to Illustrations for description and location of COMPONENTS and CONTROLS. 1. HOPPERS. To remove the hoppers si
ملخص المحتوى في الصفحة رقم 7
START-UP PROCEDURE Caution: Make sure that the Heater Switches, are in the OFF position. 1. Connect the ¼ inch copper waterlines to the ¼ inch flare water inlet fittings of the valves. 2. Plug the power cords into dedicated receptacles. 3. Activate the Power Switch (Toggle Up). The door display panel, the red power indicator lights and the green dispense buttons will light up and the tanks will start filling. Allow approximately 4-5 minutes for the tanks to fill. 4. Activate the He
ملخص المحتوى في الصفحة رقم 8
TROUBLESHOOTING GUIDE WARNING: To reduce the risk of electrical shock, DISCONNECT POWER CORDS before repairing or replacing any internal components of the unit. Before any attempt to replace a component be sure to check all electrical connections for proper connection. PROBLEM PROBABLE CAUSE REMEDY 1 A Dispensing unit unplugged. Reconnect dispensing unit. Light display B No power from Terminal Block. Check the Terminal Block for loose wire. not lit. C Defective Bulb. Replace B
ملخص المحتوى في الصفحة رقم 9
Model L690A (Rev. B) Dual Probe Liquid Level Controller Overview - The L690A is a Dual Probe Liquid Level Controller designed to maintain a specific level of water in the tank. This device utilizes two level probes for increased reliability. Independent maximum fill timers are incorporated in the controller for overflow protection. Operation - When a fill problem occurs, the Dual Probe Liquid Level Controller turns OFF power to the fill valves and remains OFF until the power input
ملخص المحتوى في الصفحة رقم 10
1. RINSE WHIPPER CHAMBERS 1. ROTATE PRODUCT GUIDES UP, REMOVE HOPPERS AND REFILL WITH PRODUCT. - POSITION PAN UNDER DISPENSE TUBES. - MOVE RINSE SWITCH TO "RINSE". 2. REPLACE HOPPERS, ROTATE PRODUCT GUIDES DOWN. - PUSH AND HOLD EACH DISPENSE BUTTON 3 TO 5 SEC. 3. EMPTY DRIP TRAY. - MOVE RINSE SWITCH TO "SERVE". 4. SANITIZE* ALL EXTERIOR SURFACES. 2. EMPTY DRIP TRAY WASH, RINSE, AND SANITIZE* 1. PRODUCT HOPPER CLEANING - ROTATE PRODUCT GUIDES UP, REMOVE
ملخص المحتوى في الصفحة رقم 11
ملخص المحتوى في الصفحة رقم 12
GB5MV-10-LD (VISTA) 5 Flavor Cappuccino Dispenser Door not shown HOPPER (4) HOPPER (1) (CD185) (CD179) 5 5 5 5 10 Lbs Lbs Lbs Lbs Lbs HEATER LIGHT PRODUCT GUIDE HEATER SWITCH POWER SWITCH WHIPPER CHAMBER RINSE SWITCH GRILL DRIP TRAY PAN
ملخص المحتوى في الصفحة رقم 13
GB6M-10-LD-U GB8M-10-LD-U GB6MP-10-LD-U GB8MP-10-LD-U 6 Flavor Cappuccino Dispenser 8 Flavor Cappuccino Dispenser Upper Door open, Lower Door not shown. Upper Door open, Lower Door not shown. UPPER DOOR UPPER DOOR OPEN OPEN GAS SPRING (2) GAS SPRING (2) DOOR LIFTS DOOR LIFTS HOPPER HOPPER HOPPER 5 5 5 5 5 10 5 5 5 5 5 5 5 10 (CD185) (CD180) (CD180) Lbs Lbs Lbs Lbs Lbs Lbs Lbs Lbs Lbs Lbs Lbs Lbs Lbs Lbs HOPPER (CD185) POWER SWITCH PRODUCT PRODUCT HEATER LIGHT GUIDE GUIDE POWER SWITCH RINSE SWI
ملخص المحتوى في الصفحة رقم 14
WHIPPER CHAMBER IMPORTANT: SLANTED WHIPPER CHAMBERS (SEE BELOW) ARE NOT INTERCHANGEABLE WITH STANDARD STRAIGHT WHIPPER CHAMBERS. BE SURE TO ORDER USING THE CORRECT PART NUMBERS. 6 8 9 12 3 11 5 SLANTED WHIPPER 4 13 7 1 2 10 CHAMBER MARKING ITEM 1 2 2 1 2 1 1 4 1 2 1 7 1 7 1 1 1 1 11 2 12 1 IMPELLER (1 FLAT) USE W/ CD75A) 1 IMPELLER (2 FLATS) USE W/ CD75A OR CD350 1 D E T N A L S
ملخص المحتوى في الصفحة رقم 15
HOPPER COVER AGITATOR WHEEL W/SPRINGS AUGER MOTOR #CD175 (90 RPM) AUGER BUSHING FRONT CD306 NUT CD278 [2] BEVELLED SOCKET CD271 PRODUCT GUIDE, SHORT AUGER BUSHING-BACK CD279 CD70A HOPPER BASE CD140
ملخص المحتوى في الصفحة رقم 16
HOPPER COVER AGITATOR WHEEL W/SPRINGS AUGER MOTOR #CD175 (90 RPM) AUGER BUSHING FRONT CD306 NUT CD278 [2] BEVELLED SOCKET CD271 PRODUCT GUIDE, SHORT AUGER BUSHING-BACK CD279 CD70A HOPPER BASE CD140
ملخص المحتوى في الصفحة رقم 17
BODY ASS'Y GB5MV-10-LD (Vista) ITEM DESCRIPTION P/N QTY
ملخص المحتوى في الصفحة رقم 18
DOOR ASS'Y GB5MV-10-LD (Vista) ITEM DESCRIPTION P/N QTY
ملخص المحتوى في الصفحة رقم 19
ملخص المحتوى في الصفحة رقم 20
DOOR ASS'Y GB6MP-10-LD-U (Panorama) GB8MP-10-LD-U (Panorama) ITEM GB6MP GB8MP DESCRIPTION OF COMPONENTS FOR MACHINES NO. P/N QTY P/N QTY WITH MOLDED FRONT GB6MP AND GB8MP 1 SK61A 1 SK43A 1 INSIDE DOOR PANEL, UPPER DOOR 2 SK65A 1 SK45A 1 INSIDE DOOR PANEL, LOWER DOOR 3 SK60A 1 SK42A 1 DOOR HOUSING, UPPER 4 SK50A 1 SK44A 1 DOOR HOUSING, LOWER 5 M903A 1 M915A 1 MOLDED UPPER DOOR PANEL 11 6 M904A 1 M916A 1 MOLDED LOWER DOOR PA NEL 10 NN13A 1 NN52A 1 SWITCH PANEL LABEL
