ملخص المحتوى في الصفحة رقم 1
Fry Warmer
MODELS FW-12, FW-15, FW-12T, FW-15T, FW-15DTO
Service Manual
Serial Numbers 120182 and Higher
ملخص المحتوى في الصفحة رقم 2
Warranty Information LIMITED ONE YEAR WARRANTY BKI (The "Company") warrants to the original purchaser that at time of shipment from the Company factory, this equipment will be free from defect in materials and workmanship. Written notice of a claim under this warranty must be received by the Company within ONE YEAR from the date of installation, but no longer than ONE YEAR AND THREE MONTHS from date of shipment from the factory. Defective conditions caused by abnormal use or misuse, la
ملخص المحتوى في الصفحة رقم 3
Fry Warmer Table of Contents Table of Contents Table of Contents .................................................................................................................................................... 1 Introduction.............................................................................................................................................................. 2 Safety Precautions ...................................................................................
ملخص المحتوى في الصفحة رقم 4
Fry Warmer Introduction Introduction Congratulations! You have chosen a Fry Warmer that will give you many years of fine service from the original manufacturer, BKI. The BKI name and trademark on this unit assures you of the finest in design and engineering — that it has been built with care and dedication — using the best materials available. Attention to the operating instructions regarding proper installation, operation, and maintenance will result in long lasting dependability to
ملخص المحتوى في الصفحة رقم 5
Fry Warmer Introduction Keep this manual with the Equipment This manual is an important part of your equipment. Always keep it near for easy access. If you need to replace this manual, contact: BKI Technical Services Department P.O. Box 80400 Simpsonville, S.C. 29680-0400 Or call toll free: 1-800-927-6887 Outside the U.S., call 864-963-3471 Protect Children Keep children away from this equipment. Children may not understand that this equipment is dangerous for them and oth
ملخص المحتوى في الصفحة رقم 6
Fry Warmer Introduction Safety Labels 4
ملخص المحتوى في الصفحة رقم 7
Fry Warmer Installation Installation Serious injury, equipment damage or death could result if attempting to install this unit yourself. Ensure that an authorized BKI service agent install the oven. Instructions For Shipping Damage You are responsible for filing all freight claims with the delivering truck line. Inspect all cartons and crates for damage when they arrive. If there is damage noted to shipping crates or cartons, or, if a shortage is found, note this on the bill of lad
ملخص المحتوى في الصفحة رقم 8
Fry Warmer Installation 8. Connect wires of power cord to power entry terminal block according to the wiring diagram attached to the unit or provided in the Service Manual. 9. Position main unit on the adapter and secure using #8 sheet metal screws. 10. Fit pan insert to main unit by lifting the open side of pan insert over the two tabs on main unit and lower the pan insert into the opening in the adapter. Countertop Cutout (FW-12 & FW-12T) 1. Obtain a suitable countertop locat
ملخص المحتوى في الصفحة رقم 9
Fry Warmer Installation Countertop Cutout 1. Obtain a suitable countertop location for the unit that will provide a clearance of 4” from the side louvers. 2. Cut a 16” x 18” hole in the countertop to fit the pan insert. 3. Using a 1/8” drill bit, drill holes in the countertop used to secure the main unit to the countertop. 4. Using a 2” hole saw, drill a hole in the countertop (under where the main unit will be secured) for the power cord to pass through. 5. Feed power cord
ملخص المحتوى في الصفحة رقم 10
Fry Warmer Installation 4. Secure WB31216000 to countertop with # 8 sheet metal screws. 5. Seal WB31216000 to the countertop to conform to NSF Standard 4, Item 4.28. (Dow Corning RTV #732 Multi purpose Sealant.) 6. Feed power cord (supplied), up through holes in WB31216000. 7. Connect wires of power cord to power entry terminal block according to the wiring diagram attached to the unit or provided in the Service Manual. 8. Position main unit on WB31216000. 9. Fit pan insert
ملخص المحتوى في الصفحة رقم 11
Fry Warmer Installation 8. Position main unit on WB31211900. 9. Fit pan insert to main unit by lifting the open side of pan insert over the two tabs on main unit and lower the pan insert into the opening in the countertop. FW-15T/FW-15DTO (Bottom Breather) Countertop Collar Weldment With Liner Pan (WB31217700) 1. Obtain a suitable countertop location for the unit. 2. Cut holes in the countertop for the countertop collar weldment with liner pan (WB31217700) according to illust
ملخص المحتوى في الصفحة رقم 12
Fry Warmer Maintenance Maintenance Failure to comply with the maintenance below could result in a serious accident. Electrocution, equipment failure or property damage could result if an unlicensed electrician performs electrical repair. Ensure that a licensed electrician perform electrical repair. Scheduled Maintenance Cleaning This unit should be cleaned at the end of each working day. Use the following procedure: Failure to remove power from this unit may cause severe ele
ملخص المحتوى في الصفحة رقم 13
Fry Warmer Maintenance Troubleshooting Refer to the table below for troubleshooting information. Problem Cause Possible Solution Warmer chute is not Ceramic heating Contact an authorized BKI service agent for holding heat element failure corrective action. Noisy fan Fan blade is dirty or fan Contact an authorized BKI service agent for bearings are failing corrective action. FW-15/FW-15T/FW-15DTO (Bottom Breather) No power to unit. Make sure that the circuit breaker and switch at t
ملخص المحتوى في الصفحة رقم 14
Fry Warmer Replacement Parts Replacement Parts Use the information in this section to identify replacement parts. To order replacement parts, call your local BKI sales and service representative. Before calling, please note the serial number on the rating tag affixed to the unit. Components FW-12/FW-15 CUF (Side Breather) 12
ملخص المحتوى في الصفحة رقم 15
Fry Warmer Replacement Parts PART # QTY DESCRIPTION B0066 1 BULB, 40A15 130V TEFLON COATED C0119 1 CALROD, 120V 1000W 140C C/U SWITCH C0080 2 CALROD, 120V 400W CERAMIC CS0024 1 CORD SET, 12/3 SJTO 8' 30"LEAD FB31204803 1 DIVIDER PAN FW CUF WB31219900 1 GREASE DEFL.RET.BRKT.WELD FW LH0021 1 LAMPHOLDER, #62602 HI TEMP M0093 1 MOTOR BLOWER ASSY 120V P0129 1 PAN INSERT 12" FW P0121 1 PAN INSERT 15" FW S0356 1 SWITCH, ROCKER 16A 250V 13
ملخص المحتوى في الصفحة رقم 16
Fry Warmer Replacement Parts FW-12/FW-15 PASS THRU (Side Breather) 14
ملخص المحتوى في الصفحة رقم 17
Fry Warmer Replacement Parts PART # QTY DESCRIPTION B0555* 1 BULB, 150W 240V HALOGEN COATED (220V England) B0066 1 BULB, 40A15 130V TEFLON COATED C0119 1 CALROD, 120V 1000W 140C C/U SWITCH C0080 2 CALROD, 120V 400W CERAMIC C0127* 1 CALROD, 220V 1000W 140C C/U SWITCH (220V England) C0057* 2 CERAMIC HTR 400W FULL SIZE 220/240V (220V England) CS0024 1 CORD SET, 12/3 SJTO 8' 30"LEAD FB31201503 1 DIVIDER PAN, FW15 WB31219900 1 GREASE DEFL.RET.BRKT.WELD FW LH0021 1 LAMPHOLDER, #6
ملخص المحتوى في الصفحة رقم 18
Fry Warmer Replacement Parts FW-15 CUF (Bottom Breather) 16
ملخص المحتوى في الصفحة رقم 19
Fry Warmer Replacement Parts PART # QTY DESCRIPTION B0066 1 BULB, 40A15 130V TEFLON COATED C0119 1 CALROD, 120V 1000W 140C C/U SWITCH C0080 2 CALROD, 120V 400W CERAMIC CS0024 1 CORD SET, 12/3 SJTO 8' 30"LEAD FB31204803 1 DIVIDER PAN FW CUF WB31219900 1 GREASE DEFL.RET.BRKT.WELD FW LH0021 1 LAMPHOLDER, #62602 HI TEMP M0093 1 MOTOR BLOWER ASSY 120V P0121 1 PAN INSERT 15" FW 17
ملخص المحتوى في الصفحة رقم 20
Fry Warmer Replacement Parts FW-15 PASS THRU (Bottom Breather) 18
