Invacare Reliant 1081003 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

 


 !!"



NOTE: Check all parts for shipping damage before
Pendant
using. In case of damage, DO NOT use. Contact the
Dealer/Carrier for further instructions.
Up
SAFETY SUMMARY
FIGURE 1 - RAISING THE BATH LIFT
The following recommendations are made for the
safe installation of the Mounting Kit on the Reli-
2. Remove the battery pack by grasping the handgrip
ant Bath Lift (RBL250).
on battery pack and

ملخص المحتوى في الصفحة رقم 2

LIFT THE SEAT REMOVING THE BATH LIFT FROM THE BATHTUB (FIGURE 8) WARNING Use proper lifting techniques to avoid in- jury. Keep back straight and bend knees when lifting components of the Bath Lift. CAUTION Frame Slide Block ALWAYS release suction cups from bathtub Groove bottom BEFORE removing frame to prevent damage to the frame or bathtub. FIGURE 4 - REMOVING THE SEAT 6. Install the battery pack by grasping the handgrip 1. Tilt the frame forward towards the drain or gently pull up and sliding

ملخص المحتوى في الصفحة رقم 3

4. Twisting EXISTING suction cup from side, pull the the Screwdriver suction cup off of the bath lift base frame (FIGURE 10). Bath Lift Base Frame Bath Lift EXISTING End Plug Base Frame EXISTING Locking Clip NOTE: Rubber Pad removed for clarity. EXISTING Suction Cup FIGURE 12 - REMOVING THE EXISTING FIGURE 10 - REMOVING THE EXISTING END PLUG SUCTION CUP 4. Twisting EXISTING Rubber Pad from side, pull the the suction cup off of the bath lift base frame (FIGURE 13). 5. Leave EXISTING locking cl

ملخص المحتوى في الصفحة رقم 4

2. Remove the battery pack by grasping the handgrip WARNING on battery pack and pull upwards (FIGURE 17). Lifting column MUST be in lowest position BEFORE installing frame to prevent tipping. The frame should be placed into an EMPTY PULL UP TO bathtub. REMOVE
Back of Front of the Bathtub Frame the (fixture end) Battery Bathtub Pack Frame Suction Cup Rubber Pad FIGURE 17 - REMOVING THE BATTERY PACK FIGURE 15 - INSTALLING THE BATH LIFT INTO 3. Lower the seat onto the frame, ensuring that the sli

ملخص المحتوى في الصفحة رقم 5

Positioning the Bath Lift Frame in the 2. Ensure the pads and suction cups are positioned flat on the bottom of the bathtub. Bathtub (FIGURE 19) 1. Position the frame to align the line on the entry/exit NOTE: Pull up on suction cup loops to release suc- side flap with the inside edge of the bathtub as tion cups from bathtub bottom. shown in the FRONT VIEW of FIGURE 19. 3. Press firmly down onto the two (2) front suction cups WARNING to attach the frame securely to the bottom of the bath. The fra

ملخص المحتوى في الصفحة رقم 6

NOTES 6

ملخص المحتوى في الصفحة رقم 7

LIMITED WARRANTY PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975. This warranty is extended only to the original purchaser/user of our products. This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state. Invacare warrants the products manufactured to be free from defects in materials and workmanship for a period of one (1) year from the date of purchase.

ملخص المحتوى في الصفحة رقم 8

#"!$! !  %&     !"#$%&' ( )))   *+,, + +*) -) + , .   /'01+2