ملخص المحتوى في الصفحة رقم 1
WASHER INSTALLATION INSTRUCTIONS
Table of Contents
WASHER SAFETY............................................ 1
INSTALLATION REQUIREMENTS ................. 2
Tools and Parts ............................................. 2
Location Requirements................................. 3
Drain System................................................. 3
Electrical Requirements ................................ 4
INSTALLATION INSTRUCTIONS ................... 4
Before You Start...................................
ملخص المحتوى في الصفحة رقم 2
INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Alternate Parts The parts supplied are in the washer basket. Your installation may require additional parts. For ordering information, please refer to the toll-free phone numbers on the Tools needed for connecting the drain hose and water front page of the Washer User Instructions. inlet hoses: If You Have: You Will Need to Buy: Pliers that open to Flashlight (optional) 3.95 cm
ملخص المحتوى في الصفحة رقم 3
Location Requirements Drain System Selecting the proper location for your washer improves The washer can be installed using the standpipe drain system performance and minimizes noise and possible washer “walk.” (floor or wall), the laundry tub drain system, or the floor drain system. Select the drain hose installation method you need. See Your washer can be installed in a basement, laundry room, closet, “Tools and Parts.” or recessed area. See “Drain System.” IMPORTANT: Do not install or st
ملخص المحتوى في الصفحة رقم 4
Electrical Requirements Do not earth to a gas pipe. Check with a qualified electrician if you are not sure the WARNING washer is properly earthed. Do not have a fuse in the neutral or earth circuit. EARTHING INSTRUCTIONS For an earthed, cord-connected washer: Electrical Shock Hazard This washer must be earthed. In the event of a malfunction Electrically earth this appliance. or breakdown, earthing will reduce the risk of electrical shock by providing a path of least resistance for ele
ملخص المحتوى في الصفحة رقم 5
4. Pull yellow shipping strap firmly, until both ends are completely removed from washer. Laundry tub drain or standpipe drain Connecting the drain hose form to the corrugated drain hose C 5. Check that the two (2) cotter pins were removed with the shipping strap. AB A. Place end of drain hose form around hose at drain hose relief. Squeeze the latch of the drain hose form until it snaps into place. B. Place the other end of the drain hose form around one of the remaining drain hose rel
ملخص المحتوى في الصفحة رقم 6
Connect the inlet hoses with the adapters, to the water faucets Connect the inlet hoses to the washer Make sure the washer basket is empty. A 1. Attach the end of the hose with the adapter, labeled hot, to the hot water faucet. Screw on coupling by hand until it is seated B on the washer. 2. Attach the end of the hose with the adapter, labeled cold, to the cold water faucet. Screw on coupling by hand until it is seated on the washer. 3. Using pliers, tighten the couplings with an addition
ملخص المحتوى في الصفحة رقم 7
2. Screw the locknut onto each foot to within 2.5 cm (1") of the foot base. Secure the Drain Hose 1. Remove the shipping strap from the power cord. Drape the power cord over the console. 2. Remove any cardboard used to move washer. 2.5 cm (1") 3. Screw the feet into the threaded holes at the front corner of the washer until the nuts touch the washer. Twist the feet to install. Beaded tie strap NOTE: Do not tighten the nuts until the washer is level. 3. Wrap the drain hose to the laundry tub
ملخص المحتوى في الصفحة رقم 8
4. If the washer is not level, move the washer out slightly, tip back, prop up the front of the washer with the wood block and Complete Installation adjust the feet up or down as necessary by twisting the feet. 1. Check the electrical requirements. Be sure that you have the Turn the feet clockwise to raise the washer or correct electrical supply and the recommended earthing counterclockwise to lower the washer. Repeat steps method. See “Electrical Requirements.” 1 through 4 until washer i
