Frigidaire 5303937140 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

(26)- (417/FRIGIDAIRE) FRONT LOAD WASHER DOOR
BOOT #5303937140 REPLACEMENT PROCEDURE

ملخص المحتوى في الصفحة رقم 2

\\'-\_IIER I'UMBLE \CTION WASHER PRO B I, E L'\ I: PROCEDURE FOR REPLACING THE BOOT Replacement of the BOOT on the Front Load Tumble -\cnon Washer _s to man_ techmclans, a job best a',otded at allcosts Sooner or latet youwdlbeconfrontedbythlslob and wlfl_ahttlepreparatlonundel .your belt you may be pleasantly surprised to learn that ttts easmr than antiapated Fhl_ tutol _al \,,ill show you how to do the job, what pitfalls to avotd and _,dl[ include some great hps if the machine has a Dry'er stac

ملخص المحتوى في الصفحة رقم 3

FRONT LO-kD \VASHER PRO('EI)URE FOR REPLACING TItE BOO f continued In tllustratlon #3 },ou \,,tit see that the end oftbe tube _s flattened somewhat sn that it can be 4) shpped o;'er the twisted ends of the clamp as shown tn dlustranon _ 4 ILLUSTRATION # 4 II.I USTRATION # l'\_d_t the robe counterclockxvlse to slip the clamp and set both the tool and the wire clamp aside Pull the boot flee from the duct 5) Using both hands, grab onto the boot at the top of the opening to the tub and pull downward

ملخص المحتوى في الصفحة رقم 4

i. t,:ON I 1.O \D \\'-'_SHER _'_( ',Z'_'OIIRF FOil RFPI_ kC|NG I HE BO()] continued ILLUSTRATION # 6 ILLUSTRATION # 5 "! Once the groove m the boot is lubed _,Ath soap, locate the arrow as shown m figure #6 that is located on the top of the boot (located to the right of the extrusion that slips over the duct) Yhts arrow must point up when the boot ts installed '_',hththe boot m one hand and the other hand spreading the hp and groove (on the boot near the arro_ ), tbrce the lip rata the groove be

ملخص المحتوى في الصفحة رقم 5

FRONT LQAD _VAStlER PROCEDURE FOR REPI. k('ING TflE BOOT continued [ql I Now is the tnne to put the spring back on Included m the BOOT KIT is a set of three spacel >(an e,:ample ofx_hlch _ashown m # 9 below) These spaceis are to be used to hold the spring in place m the groove on the outside pernneter of the boot As it will take both hands to sh etch th_s spNng into place, these spacers will pievent the spnng from popping out when you let go oDt to use both hands to stretch it fiwther around the

ملخص المحتوى في الصفحة رقم 6

FRONT LO-\D \\ tSIIER PROCEDURE FOR REPL_kCING THE BOO I colmnued 141 Replace the boot e\truslon back onto tile duct and pull it up ovei tile ridge on the duct neai the top of the opening Reinstall the clamp m such a way that the clamp sits between the ndges on the extrusion and above the ndge on the duct Snap the clamp closed _,,aththe copper tubing tool that You used prexlously 1_) Betbre attaching the new boot to the front panel, clean the surface of the front panel with alcohol or household