ملخص المحتوى في الصفحة رقم 1
P/N 8514-162-001B
MODEL T1200
80LB CAPACITY
COMPUTER CONTROL
OPL WASHER
DEXTER
LAUNDRY,
INC.
OWNER'S BOOKLET
INSTALLATION & OPERATION
INSTRUCTIONS
Please read this information and retain for reference.
WARNING - THIS WASHER IS EQUIPPED WITH DEVICES AND FEATURES RELATING TO ITS SAFE
OPERATION. TO AVOID INJURY OR ELECTRICAL SHOCK, DO NOT
ملخص المحتوى في الصفحة رقم 2
1 Load clothes, and latch door firmly. 2 If required, put detergent and fabric softener, into dispenser on front of machine. Add detergent (See the dispenser diagram at right.) 3 Select desired wash CYCLE with and buttons. Add 4 Press START button. Bleach FLUSH W PA RE SH WASH RINSE RI FINS NAL E SPIN 5 If bleach is required, add when ADD BLEACH light comes on. Add fabric softener (Optional) Door locks when machine starts, and remains locked until cycle is completed. If po
ملخص المحتوى في الصفحة رقم 3
MODEL T1200 DEXTER LAUNDRY, INC. INSTALLATION INSTRUCTIONS All washers must be installed in accordance with all local, state and national building, electrical, plumbing and other codes in effect in the area. WARNING - THESE INSTALLATION AND SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED PERSONNEL ONLY. TO AVOID INJURY AND ELEC
ملخص المحتوى في الصفحة رقم 4
CONCRETE PEDESTAL MOUNTING FLOOR OUTLINE Figure 1-1 Figure 1-2 MACHINE MOUNTING DETAIL Figure 1-3
ملخص المحتوى في الصفحة رقم 5
PLUMBING Water supply hoses are furnished with each machine. The threaded connections on the hoses are ¾- 11 ½ NHT. The small 3/8 ID supply hoses and supplied brass shut off valves connect to the lower hot and cold valves which flush the soap box. The brass shut off valves can connect to either the store supply side or the machine inlet side. In case of water splash out due to high water pressure, adjust brass shut off valves while machine is running until splash out stops. The larger 5/8
ملخص المحتوى في الصفحة رقم 6
INJECTION SOURCE DETAILS The washer control may be programmed to send 120V output signals for a chemical injection system. The signals are not intended as a power source and must be limited to less than 100 milliamps of current. There is a separate terminal block for connection of the external injection signals. For the injection sources, program codes 0 through 6 are as shown in the table below. Dexter Controller Injection Recommended Programmed Terminal Block Connections S
ملخص المحتوى في الصفحة رقم 7
SPECIFICATIONS MODEL T1200 80LB WASHER CAPACITY 80LBS/11.5 CUBIC FT. (36.3 kg/326 l) CYLINDER SIZE 30” DIA X 28” DEEP (76cm X 71cm) ELECTRICAL 208-240 VAC, 60 HZ, 1 OR 3 PHASE DRIVE SYSTEM SOFT START REVERSING INVERTER DRIVE WASH SPEED 43 RPM INTERMEDIATE 375 RPM (60 G’S) EXTRACT FINAL EXTRACT 485 RPM (100 G’S) MACHINE CONTROL PROGRAMMABLE COMPUTER WATER INLET 4 SOLENOID OPERATED VALVES FLOW RATE: 9 TO 12 GAL/MIN EACH, 30-120 PSI DRAIN VALVE 3” DIAMETER
ملخص المحتوى في الصفحة رقم 8
STARTING THE WASHER A. Load the clothes into the cylinder and latch the door securely. Be sure clothing does not get caught between the door gasket and tub front when closing the door. Maximum load is 80 pounds clothes, dry weight. Do not load the washer with more than 80 lbs. B. Select the appropriate cycle number (1 through 6) using for the load being washed. See the cycle descriptions in the programming section. Use the UP and DOWN keys to change the cycle number. C. If not
ملخص المحتوى في الصفحة رقم 9
PROGRAMMING INSTRUCTIONS: Programming can be accomplished manually using the machine controls or by connecting to the machine control using a PDA (personal digital assistant). For instructions on using a PDA with this washer control, please contact your local Dexter distributor. Please read below for manual programming instructions. The keypad layout for the washer control is shown above. WASH CYCLE PROGRAMMING: 1. Turn on the power to the washer. 2. Turn the Run/Program ke
ملخص المحتوى في الصفحة رقم 10
DISPLAY FUNCTION OPTIONS Ct ** Tumble Time Two-digit amount of time in minutes. t ** Water Temperature HH for hot, CH for warm, CC for cold and EE for no water. L ** Water Level Lo for low, Hl for high. 1 dF * Type of Fill d for delayed fill, t for timed fill. S ** Spin Time Two-digit amount of time in minutes. 2 IS * Injection Source Single digit code indicating injector signal(s). 1 A delayed fill will pause the time count until the selected level is reached. A timed fil
ملخص المحتوى في الصفحة رقم 11
Cycle 1 Sheets & Pillowcases (Health Care) Bath Bath Cycle Water Water Delay Spin Injection Source Time Temp. Level Fill Time (min.) (min.) Flush 3 CH HI d Prewash 2 CH HI d Wash 7 HH LO d 1 (Detergent) Rinse 1 7 HH LO d 2 (Bleach) Rinse 2 2 CH HI d 1 Rinse 3 2 CH HI d Rinse 4 Final 4 CH LO d 4 4 (Sour/Soft) Rinse Cycle 2 Towels / Pads / Diapers (Health Care) Bath Bath Cycle Water W
ملخص المحتوى في الصفحة رقم 12
Cycle 3 White Towels (Hotel / Motel) Bath Bath Cycle Water Water Delay Spin Injection Source Time Temp. Level Fill Time (min.) (min.) Flush Prewash Wash 7 HH LO d 1 (Detergent) Rinse 1 1 HH HI d Rinse 2 7 HH LO d 2 (Bleach) Rinse 3 2 CH HI d 1 Rinse 4 2 CH HI d Final 4 CH LO d 5 4 (Sour/Soft) Rinse Cycle 4 Guest Laundry (Hotel / Motel or Health Care) Bath Bath Cycle Water Water De
ملخص المحتوى في الصفحة رقم 13
Cycle 5 Rags & Mops (Hotel / Motel) Bath Bath Cycle Water Water Delay Spin Injection Source Time Temp. Level Fill Time (min.) (min.) Flush 3 CH HI d Prewash 2 CH HI d Wash 2 CH HI d Rinse 1 7 HH LO d 1 (Detergent) Rinse 2 2 HH HI d Rinse 3 7 HH LO d 2 (Bleach) Rinse 4 2 CH HI d 1 Final 2 CH LO d 5 Rinse Cycle 6 Colored Cotton Linen (Food & Beverage) Bath Bath Cycle Water Water Delay Spin
ملخص المحتوى في الصفحة رقم 14
RAPID ADVANCE MODE To enter the Rapid Advance mode, turn the key counter-clockwise (CCW). The Rapid Advance setting is not marked next to the key, but turning the key CCW until it stops selects this mode. The Rapid Advance mode can be entered from either the Idle mode or during the cycle. If the cycle has not yet started, press the “START” button. To rapid advance to the next step in the wash cycle, push both the “UP” and “START” buttons at the same time. The display will show an “Ad”
ملخص المحتوى في الصفحة رقم 15
WASHER ERROR CODES Fault # Description Customer Action (F #) 1 The door failed to close and lock or the door Turn off the power to the washer. Check wire connections to door /lock switches. Check wire failed to remain locked after three tries of connections from switches to controller. If necessary the door lock mechanism should be latching the door and starting during the cycle. adjusted by a qualified person. Turn on the power to the washer. (See Note) 2 The washer tub does not fi
ملخص المحتوى في الصفحة رقم 16
11 The drive size setting has changed. Turn off the power to the washer. Check to ensure all the harnesses are properly connected to the controller. Check to ensure the drive horsepower is proper for this size of washer. Turn on power to the washer. (See Note) If problem reappears, contact your Dexter representative. 12 Washer controller internal error Turn off the power to the washer. Wait one minute. Turn on the power to the washer. (See Note) If problem reappears, contact your D
ملخص المحتوى في الصفحة رقم 17
ACCESSORIES INSTALLATION: (Furnished) QTY. 9990-027-013 Hose, Water Supply 2 9990-027-011 Hose, Water Supply 2 9379-197-001 Valve, Shut Off 2 8641-242-000 Washer, Inlet Hose 4 9565-003-001 Strainer, Inlet Hose 8 Contact your distributor or Dexter Laundry, Inc. if a steel-mounting base is required. www.dexterlaundry.com
