ملخص المحتوى في الصفحة رقم 1
Solar Shed light
Model 95573
aSSeMbly and operation inStructionS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
t o preVent SeriouS injury, read and underStand
all warningS and inStructionS before uSe.
© ®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced
ملخص المحتوى في الصفحة رقم 2
SpecificationS Solar Panel Polycrystalline Silicon Solar Panel Type 4-Watt Fluorescent Light w/Output Equivalent Light to 30 Watts Incandescent Power Cord 18 Gauge x 2C x 10’ Lens Acrylic Plastic Lens Approximately 50 Minutes Continuous Run Time on Run Time Fully Charged Batteries Battery 4 AA (1.2 VDC) 500 mAH NiCd Rechargeable Batteries Requirement (included) Light Fixture 3-1/16”L x 7-15/16”W x 2-3/16”H Dimensions Weight 1.85 Lb. Save this Manual You will need this manual for the safety w
ملخص المحتوى في الصفحة رقم 3
2. do not expose the Shed light assembly to rain or wet conditions. You can however place the solar panel outside, exposed to the elements. 3. do not abuse the power cord. never use the power cord to carry the Shed l ight or pull the plug from an outlet. k eep the power c ord away from heat, oil, sharp edges, or moving parts. replace damaged power cords immediately. Damaged Power Cords increase the risk of electric shock. perSonal Safety 1. Stay alert. watch what you are doing, and use
ملخص المحتوى في الصفحة رقم 4
Specific Safety ruleS 1. Maintain labels and nameplates on the Shed light. These carry important infor- mation. If unreadable or missing, contact Harbor Freight Tools for a replacement. 2. Maintain a safe working environment. Make sure there is adequate surrounding workspace. Do not use this product in a damp or wet location. Do not set up the Solar Shed Light if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgement or reflexes are i
ملخص المحتوى في الصفحة رقم 5
inStallation inStructionS note: Your Solar Shed Light will require installation. It is important that you read the entire manual to become familiar with the product BEFORE you use the Solar Shed Light. Before operating this product be sure that you have all parts described in the Parts List and Assembly Diagram located on page 10 of this manual. 1. If you do not have experience or have not done wiring of this type before, contact a qualified electrician to install the Solar Shed Light. 2.
ملخص المحتوى في الصفحة رقم 6
7. Mount the Bracket (8) to the shed using the Screws (23) and/or Anchors (24). When using Anchors (24) drill holes the size of the Anchors. Tap Anchors in with a ham- mer (not included). 8. Attach the Solar Panel (1) to the Bracket (8) using the Bracket Knobs (9), then at- tach the Power Cord (10) to both the Light and the Solar Panel (1). 9. Turn OFF the Shed Light Switch (21). Tilt the Solar Panel to catch the sun’s rays. 10. After the initial charge is set, turn ON the Shed Light Switch
ملخص المحتوى في الصفحة رقم 7
2. To change the batteries, carefully remove the Solar Panel (1) from the Bracket (8) by turning the Bracket Knobs (9) counterclockwise. Place the Solar Panel assembly on a flat, uncluttered surface. 3. Remove the battery covers from Battery Housing (4) by pressing the battery cover tabs inward, while pulling them up and out. figure 3 Battery (3) Back View of Solar Panel 4. Remove the old batteries (note the polarity position of the old batteries). Make certain that the new batteries are
ملخص المحتوى في الصفحة رقم 8
figure 4 Light Tube (19) 4. Insert the Light Tube (19) into the closed end of the lamp first, then slide it into the open end. Rotate 90 degrees to lock in place. See Figure 5. figure 5 Lens (20) 5. Make certain that the light is replaced with an identical Light Tube (19). Do not force. Replace the Lens (20). Snap shut. See Figure 5. caution: Light Tubes (19) are fragile and can easily break. Be careful when discarding bulbs. When replacing the bulb, use the appropriate clothing including ANS
ملخص المحتوى في الصفحة رقم 9
inSpection, Maintenance, and cleaning 1. warning! Make sure the Power Switch is in its “OFF” position and that the product is unplugged from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. 2. before each uSe, inspect the general condition of this product. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. do not use a d
ملخص المحتوى في الصفحة رقم 10
partS liSt part description Qty part description Qty 1 Solar Panel 1 14 Left Baffle 1 2 Battery Cover 2 15 Back Housing w/Reflector Strip 1 3 Battery 4 16 Right Housing 1 4 Battery Housing 1 17 Right Baffle 1 5 Long Screws 4 18 Socket 2 6 Short Screws 4 19 Light Tube 1 7 Nut M5 2 20 Lens 1 8 Bracket 1 21 Switch Assembly 1 9 Bracket Knobs 2 22 Screws 8 10 Power Cord 1 23 Screws (5/16” long) 4 11 Left Housing 1 24 Anchor 4 12 Charging Base 1 13 Circuit Board 1 aSSeMbly diagraM 8 SKU 95573 for tech
ملخص المحتوى في الصفحة رقم 11
LIMIted 90 dA y w AA rr nty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of ninety days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, or to lack of maintenance. We s
