ملخص المحتوى في الصفحة رقم 1
INSTALLATION INSTRUCTIONS
24" (61.0 CM) ELECTRIC SINGLE AND DOUBLE
BUILT-IN OVEN
Table of Contents
BUILT-IN OVEN SAFETY .................................1
INSTALLATION REQUIREMENTS ..................2
Tools and Parts..............................................2
Location Requirements..................................2
Electrical Requirements.................................4
INSTALLATION INSTRUCTIONS ....................4
Prepare Built-In Oven ....................................4
Remove Oven
ملخص المحتوى في الصفحة رقم 2
INSTALLATION REQUIREMENTS Product Dimensions - Single Oven Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed A here. Tools needed ■ Phillips screwdriver ■ Hand or electric drill (for wall cabinet installations) ■ Measuring tape B ■ 1" (25 mm) drill bit E ■ Level (for wall cabinet installations) Parts needed ■ UL listed or CSA approved conduit connector ■ UL listed wire connectors D C Parts supplied
ملخص المحتوى في الصفحة رقم 3
Single Oven Installed in Cabinet Cabinet Dimensions - Double Oven A Double Oven Installed in Cabinet A B B F D F D E C E C A. 24" (61 cm) min. cabinet width B. 1" (2.5 cm) top of cutout to bottom of upper cabinet door A. 24" (61 cm) min. cabinet width C. 32" (81.3 cm) bottom of cutout to floor B. 1" (2.5 cm) top of cutout to bottom of upper D. 22¹⁄₂" (57.2 cm) cutout width cabinet door E. 1¹⁄₂" (3.8 cm) min. bottom of cutout to top of C. 14³⁄₄" (37.5 cm) bottom of cutout to floor cabinet door
ملخص المحتوى في الصفحة رقم 4
Electrical Requirements INSTALLATION INSTRUCTIONS If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance with local Prepare Built-In Oven codes. 1. Decide on the final location for the oven. Locate existing Check with a qualified electrical installer if you are not sure the wiring to avoid drilling into or severing wiring during oven is properly grounded. installation. This
ملخص المحتوى في الصفحة رقم 5
3. Grasp the edges of the oven door with both hands and close the oven door until it will no longer close. Lift and pull oven Make Electrical Connection door toward you and remove. Set the oven door aside on a covered work surface. WARNING Electrical Shock Hazard Disconnect power before servicing. Use 8 gauge solid copper wire. Electrically ground oven. 4. Remove bottom screw on each side of the oven trim. 5. Grasp the bottom end of trim and pull away from oven. Failure to follow these instru
ملخص المحتوى في الصفحة رقم 6
4-Wire Cable from Home Power Supply 3-Wire Cable from Home Power Supply - U.S. Only IMPORTANT: Use the 4-wire cable from home power supply in IMPORTANT: Use the 3-wire cable from home power supply the U.S. where local codes do not allow grounding through where local codes permit a 3-wire connection. neutral, New Branch circuit installations (1996 NEC), mobile homes and recreational vehicles, new construction and in A Canada. B A C G B E H F D G E I H C F D I A. Cable from home power supply F.
ملخص المحتوى في الصفحة رقم 7
Install Oven 5. Securely fasten oven to cabinet using the # 8-14 x 1" screws (2 for single oven, 4 for double oven) provided. Insert the WARNING screws through holes in mounting rails. Do not overtighten screws. Excessive Weight Hazard Use two or more people to move and install oven. Failure to do so can result in back or other injury. 1. Using 2 or more people, lift oven partially into cabinet cutout. Use the oven opening as an area to grip. NOTE: Push against seal area of oven front frame
ملخص المحتوى في الصفحة رقم 8
7. Slide top end of each trim piece upward onto oven side rails. Complete Installation 1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check that you have all of your tools. 3. Dispose of/recycle all packaging materials. 4. For oven use and cleaning, read the Use and Care Guide. Check Operation of Single Oven 1. Turn power on. “PF” should appear in the display. 2. Press BROIL. “BROIL” will appear in the display.
