ملخص المحتوى في الصفحة رقم 1
8"
BENCH GRINDER
OWNER'S MANUAL
WARNING:
Read carefully and understand all INSTRUCTIONS before
operating. Failure to follow the safety rules and other basic
safety precautions may result in serious personal injury.
Item # 143388
ملخص المحتوى في الصفحة رقم 2
Thank you very much for choosing a NORTHERN TOOL + EQUIPMENT CO., INC. Product! For future reference, please complete the owner's record below: Model: _______________ Purchase Date: _______________ Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it. This machine is designed for certain applications only. Northern Tool + Equipment cannot be responsible for issues aris
ملخص المحتوى في الصفحة رقم 3
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control, so visitors should remain at a safe distance from the work area. • Be aware of all power lines, electrical circuits, water pipes and other mechanical haz- ards in your work area, particularly those hazards below the work surface hidden from the operator's view that may be unintentionally contacted and may cause personal harm or property damage. • Be alert of
ملخص المحتوى في الصفحة رقم 4
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. • Do not let your fingers touch the terminals of plug when installing to or removing from the outlet. • Ground fault circuit interrupters. If work area is not equipped with a permanently installed Ground Fault Circuit Interrupter outlet (GFCI), use a plug-in GFCI between power tool or extension cord and power receptacle. PERSONAL SAFETY
ملخص المحتوى في الصفحة رقم 5
• Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may create a risk of injury when used on another tool. • Keep guards in place and in working order. • Never leave tool running unattended. UNPACKING When unpacking the Bench Grinder, please check if any parts are missing or broken, please call Northern Tool + Equipment. Carefully remove the grinder and related hardware from the carton and examine it th
ملخص المحتوى في الصفحة رقم 6
ASSEMBLY SWITCH The switch is located on the front of the grinder near the bottom. To turn the tool ON depress the rocker switch at the top near the word ON. To turn the tool OFF depress the bottom por- tion of the rocker switch near the word OFF. INSTALLING TOOL RESTS Turn off and unplug the bench grinder. Remove the tool rests from the top portion of the poly-foam carton liner and install them to the wheel guards as shown in the figure. Use the bolts and washers from the pl
ملخص المحتوى في الصفحة رقم 7
NOTE: The eye shields are identical and will fit properly on Fig. 5 either side of the grinder. However it may be necessary to Back of loosen the center hex nut in order to slip the shield over the eye shield mounting rod. Right mounting After you have assembled and installed each-eye shield rod mounting rod to the grinder attach the eye shields to the Hex nut rods as shown in Figure 5. Install them in such a way that the three hex nuts on each eye shield are on the back s
ملخص المحتوى في الصفحة رقم 8
EYESHIELDS WARNING! Never operate grinder with eyeshields removed. Position the eyeshields so that manipulation of the work piece to the grinding stone is not obstructed by the shield and that the piece of work is between the stone and the eyeshield. SPARK DEFLECTORS • Adjust periodically to insure that the distance between O.D. of the stone/wire wheel and 1 the bottom edge of the spark deflector is /16" clearance. • Insure screws are securely tightened. TOOL RESTS 1
ملخص المحتوى في الصفحة رقم 9
MAINTENANCE WARNING! Make sure this tool is disconnected from its power source before attempting any maintenance, cleaning, or inspection. • Maintain your tools. It is recommended that the general condition of any tool be exam- ined before it is used. Keep your tools in good repair by adopting a program of conscien- tious repair and maintenance in accordance with the recommended procedures found in this manual. If any abnormal vibrations or noise occurs, turn the tool off immediat
ملخص المحتوى في الصفحة رقم 10
DIAGRAM & PARTS LIST 9
ملخص المحتوى في الصفحة رقم 11
10
ملخص المحتوى في الصفحة رقم 12
