Harbor Freight Tools 43471 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

4-1/2” ANGLE GRINDER
Model 43471
AssEMbL y AND OpERAtION INstR uctIONs
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
tO pREVENt sERIOus INjuR y, READ AND uNDERst AND
ALL wARNINGs AND INstR uctIONs bEfORE usE.
© ®
Copyright 2001, 2007 by Harbor Freight Tools . All rights reserved. No portion of
this manual or any artwork contained herein may

ملخص المحتوى في الصفحة رقم 2

ملخص المحتوى في الصفحة رقم 3

ducing metal filings or wood chips. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. 9. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines. 10. Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodi- cally and, if damaged, have them repaired by an authori

ملخص المحتوى في الصفحة رقم 4

21. Maintenance. For your safety, maintenance should be performed regularly by a quali- fied technician. 22. there are certain applications for which this tool was designed. This tool shall not be modified and/or used for any application other than which it was designed. 23. All accessories must be rated for at least the RpM speed recommended on the tool’s warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. 24. for safe operation, only these

ملخص المحتوى في الصفحة رقم 5

uNpAcKING When unpacking, check to make sure the parts listed on page 6 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. AssEMbL y warning! Make sure the unit is unplugged before assembling, or when changing discs. 1. Screw the threaded end of the side Handle (18) into the threaded hole to the right of the Gear box (17). See Assembly Drawing. 2. With one hand, hold the body of the Grinder while

ملخص المحتوى في الصفحة رقم 6

MAINtENANcE 1. Periodically blow out motor vents with compressed air. 2. Clean plastic with a damp cloth. Never use solvents. 3. No lubrication required. 4. If performance lacks, change the Carbon brush (44). a. Using a screwdriver, unscrew the brush cap (45) . b. Remove the brush (44) from the brush Holder (43). c. Replace with an identical replacement part from Harbor Freight Tools. d. Replace brush Holder (43) and brush cap (45) . LIMItED 90 DA y wARRANty Harbor Freight Tools Co. makes e

ملخص المحتوى في الصفحة رقم 7

pARts LIst part Description part Description part Description 1 Stop Pin 20 Axle Bearing 40 Switch Draw-Bar 2 Spring Washer 21 Check Ring 41 Cabinet 3 Check Ring 22 Spring Ring 42 Condenser 4 Nut 23 Gear 43 Brush Holder 5 Spring Washer 25 Bearing Cap 44 Brush 6 Pinion Gear 26 Bearing 45 Brush Cap 7 Bearing 28 Screw 46 Switch Cover 8 Check Ring 29 Woodruff Key 47 Screw 9 Fan Guide 30 Spindle 48 Cord Clamp 10 Roller 31 Screw 49 Screw 11 Armature 32 Protecting Cover 50 Switch 12 Bearing 33 Flange 5

ملخص المحتوى في الصفحة رقم 8

AssEMbL y DRAwING REV 03e, 07d SKU 43471 for technical questions, please call 1-800-444-3353. Page 8