ملخص المحتوى في الصفحة رقم 1
l
l
l
l
l
l
MO0602-EA
Operation Guide 3043
Getting Acquainted
If the display of the watch is blank...
Congratulations upon your selection of this CASIO watch. To get the most out
If the display of the watch is blank, it means that the watch’s Power Saving
of your purchase, be sure to read this manual carefully.
function has turned off the display to conserve power.
• See “Power Saving” for more information.
Applications
The built-in sensors of this watch measure direction, barometric press
ملخص المحتوى في الصفحة رقم 2
l l l l l l l l l l Operation Guide 3043 Radio-controlled Atomic Timekeeping • Signal reception normally is better at night than during the day. This watch receives a time calibration signal and updates its time setting • Time calibration signal reception takes from two to seven minutes, but in accordingly. some cases it can take as long as 14 minutes. Take care that you do not • This watch is designed to pick up the time calibration signal transmitted in perform any button operations or move th
ملخص المحتوى في الصفحة رقم 3
l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l Operation Guide 3043 • The watch receives the calibration signal for two to seven minutes everyday To turn auto receive on and off when the time in the Timekeeping Mode reaches each of the calibration 1. Enter the Receive Mode. times. Do not perform any button operation within seven minutes before or 2. In the Receive Mode, hold down E until the current auto receive setting (ON or OFF) after any one of the calibration times. Doing so
ملخص المحتوى في الصفحة رقم 4
SE ESE E ENE NE NNE N NNW Operation Guide 3043 To take a direction reading • The displayed temperature value changes to xxx °C (or °F) if a measured temperature falls outside the range of –10.0°C to 60.0°C (14.0°F to 1. While the watch is in the Digital Compass Magnetic north pointer 140.0°F). The temperature value will reappear as soon as the measured Mode, place it on a flat surface, or if you are 12 o’clock position temperature is within the allowable range. wearing the watch, make sure that
ملخص المحتوى في الصفحة رقم 5
l l l l l l l l l l l l l l l Operation Guide 3043 To turn display of the barometric pressure differential pointer on Displaying Your Current Altitude and off You can use the procedure described in this section to display your current 1. In the Barometer/Thermometer Mode, hold altitude. If you leave the watch in the Altimeter Mode, it will update the displayed altitude value regularly, and indicate reading-to-reading changes in down E until SET appears in the upper the altitude graph at the top
ملخص المحتوى في الصفحة رقم 6
l l l l l l l l l l l l l l l l l l l l l l l l l l l Operation Guide 3043 Current Session Record Other Altimeter Mode Features The Current Session Record contains the data described below. The contents This section explains other features and settings that are available in the of this record are updated at regular intervals while a save session is in Altimeter Mode. Note that all of the information in this section applies to all progress. types of Altimeter Mode measurements, unless specifica
ملخص المحتوى في الصفحة رقم 7
l l l l l l l l l l l l l l Operation Guide 3043 Altitude Alarm Current Session Record Contents The following data items show the contents of the current session record. The altitude alarm sounds for about five seconds when the current altitude matches a preset value during an altitude measurement operation. You can Data Type Screen Name Description press any button to stop the alarm after it starts to sound. Highest altitude reached during the High Altitude MAX The altitude alarm sounds only
ملخص المحتوى في الصفحة رقم 8
l l l l l l l l l l l l l Operation Guide 3043 World Time Countdown Timer Current time in the zone World Time digitally displays the current time in You can set a countdown timer start time in the Seconds Minutes of the selected city code 30 cities (29 time zones) around the world. range of one minute to 60 minutes. An alarm sounds when the countdown reaches zero. An • For full information on city codes, see the “City auto-repeat feature causes the countdown to Code Table”. restart automatically
ملخص المحتوى في الصفحة رقم 9
l l l l l l l l Operation Guide 3043 Alarms About the Auto Light Switch Alarm on indicator You can set five independent daily alarms. When Turning on the auto light switch causes illumination to turn on, whenever you an alarm is turned on, the alarm tone sounds Hourly time signal on position your wrist as described below in any mode. indicator when the alarm time is reached. Note that this watch features a “Full Auto EL Light”, so the auto light switch You can also turn on an Hourly Time Signal,
ملخص المحتوى في الصفحة رقم 10
l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l Operation Guide 3043 Power Supply Question: How does the barometer work? This watch is equipped with a solar cell and a special rechargeable battery Answer: Barometric pressure indicates changes in the atmosphere, and by (secondary battery) that is charged by the electrical power produced by the monitoring these changes you can predict the weather with solar cell. The illustration shown below shows how you should position the reasonable
ملخص المحتوى في الصفحة رقم 11
l l l l l l l l l Operation Guide 3043 Charging Precautions To set the time and date manually Certain charging conditions can cause the watch to become very hot. Avoid 1. In the Timekeeping Mode, hold down E until the city code starts to flash, leaving the watch in the areas described below whenever charging its which indicates the setting screen. rechargeable battery. 2. Use C and A to select the city code you want. Also note that allowing the watch to become very hot can cause its liquid
ملخص المحتوى في الصفحة رقم 12
l l l l l l l l l Operation Guide 3043 4. When the setting you want is selected, press E to exit the setting screen. To recover from the sleep state • The DST indicator appears to indicate that Daylight Saving Time is turned Perform any one of the following operations. on. • Move the watch to a well-lit area. It can take up to two seconds for the display to turn on. • Press any button. Reference • Angle the watch towards your face for reading. This section contains more detailed and technical in
ملخص المحتوى في الصفحة رقم 13
l l l l l l l l l l l l l Operation Guide 3043 Timekeeping Storage 00 • The precision of the bearing sensor may deteriorate if the watch becomes • Resetting the seconds to while the current count is in the range of 30 to magnetized. Because of this, you should be sure to store the watch away 59 causes the minutes to be increased by 1. In the range of 00 to 29, the 00 from magnets or any other sources of strong magnetism, including: seconds are reset to without changing the minutes. permanent m
ملخص المحتوى في الصفحة رقم 14
l l l l l l l l l l l l l l l l l l l l l l l l l l l l l Operation Guide 3043 City Code Table 4. Press A to start the calibration operation. City GMT Other major cities in same time zone • --- is shown on the display while calibration is being performed. When City Code Differential calibration is successful, the display will show OK and the Digital Compass –11 –11.0 Pago Pago 0 Mode (with ° shown as the angle value). HNL Honolulu –10.0 Papeete • If --- appears and then changes to ERR (error) on
