ملخص المحتوى في الصفحة رقم 1
Installation Guide
PMWT-660/680 Projector Wall Mount for the
SMART Board™ Interactive Whiteboard
ملخص المحتوى في الصفحة رقم 2
Product Registration If you register your SMART product, we’ll notify you of new features and software upgrades. Register online at www.smarttech.com/registration. Keep the following information available, in case you need to contact Technical Support: Serial Number ____________________________________________ Date of Purchase _________________________________________ Trademark Notice SMART Board, smarttech and the SMART logo are trademarks or registered trademarks of SMART Technologies ULC i
ملخص المحتوى في الصفحة رقم 3
Installation Overview Please read these instructions carefully before you install your projector wall mount. Use this guide to assemble and install the projector wall mount for SMART Board™ interactive whiteboards, which is a projector mount for your SMART Board interactive whiteboard (models 660 or 680) and an NEC WT600 or WT610 projector (purchased separately). The SMART Board 660 interactive whiteboard is 64" (162.6 cm) measured diagonally, and the 680 measures 77" (195.6 cm). PMWT-660,
ملخص المحتوى في الصفحة رقم 4
Other Precautions For operating safety and to avoid damage, read this guide carefully before setting up and using the projector mount. Observe the following precautions: • Adding more weight or applying an unexpected force to the projector support may cause it to break and possibly cause injury. • Do not hang anything from the support or hit or jostle it in any way. • If you require replacement parts, the service technician must use replacement parts that are specified by SMART Technologies o
ملخص المحتوى في الصفحة رقم 5
To install the projector wall mount, you must complete the following tasks: 1. Find a suitable location for the projector wall mount (page 4). 2. Install the wall mounting hardware (pages 4 and 5). 3. Assemble and mount the projector support (page 7). 4. Attach the projector plate to the projector (page 11). 5. Attach the projector to the projector support (page 12). 6. Hang the interactive whiteboard (page 13). 7. Route the projector cables (page 15). 8. Adjust the projected image on the intera
ملخص المحتوى في الصفحة رقم 6
5. Slide the pen tray off its support brackets, and set it aside in a safe location. 6. Use a No. 2 Phillips screwdriver to remove the two screws that secure the pen tray brackets to the wall. Set the screws aside, as you will reinsert them after you attach the interactive whiteboard to the projector mount. 7. Carefully remove the interactive whiteboard from the wall, and rest it on the two pen tray brackets, where it won’t be damaged. CAUTION Make sure the interactive whiteboard remains upr
ملخص المحتوى في الصفحة رقم 7
In the absence of such an outlet, you must route the projector cables through the projector mount and behind the interactive whiteboard, as described on page 16. IMPORTANT If you’re installing the projector mount for a 660, the ceiling should be at least 8'4" (2.54 m) high. If you’re installing the projector mount for a 680, the ceiling should be at least 9'1" (2.76 m) high. If the ceiling doesn’t meet these requirements, the interactive whiteboard’s pen tray will be below the recommended h
ملخص المحتوى في الصفحة رقم 8
6. Repeat this procedure for the remaining five anchor holes. 7. Thread one of the supplied 1/4-20 × 2" security hex screws into the upper right wall anchor by hand until the screw protrudes 1/4" (6 mm) from the wall. 8. Repeat this procedure for the upper left, lower left and lower right anchors. Leave the remaining two anchors vacant for now. Installing the Wall Mounting Hardware in Concrete or Cinder Block IMPORTANT A qualified technician should complete the following procedure. The technic
ملخص المحتوى في الصفحة رقم 9
Assembling and Mounting the Projector Support Follow these instructions to assemble the projector mount and mount it on the wall. Upper Support Projector Brackets Lower Support NOTE: This illustration shows the projector wall mount for the 680. Wall Mount Horizontal Bracket 1. Using the provided 5/32" security hex key, attach each projector bracket to the upper support with a No. 8-32 × 1/2" security hex screw and a No. 8-32 × 1" security hex screw, as shown in the following two diagrams. I
ملخص المحتوى في الصفحة رقم 10
1/2" Screw Projector Brackets Protruding Threaded Inserts 1" Screw Projector Bracket Attachment for a 660 Projector 1/2" Screw Brackets Protruding Threaded Inserts 1" Screw Projector Bracket Attachment for a 680 2. Lay the wall mount bracket on the floor or any large, flat surface. 3. Using the same security hex key, attach the upper support to the wall mount bracket by inserting two No. 8-32 × 1/2" security hex screws in the third hole from the top, as shown in the diagram below. Leave the
ملخص المحتوى في الصفحة رقم 11
4. Attach the lower support to the wall mount bracket by inserting two No. 8-32 × 1/2" security hex screws in the third hole from the top, as shown in the diagram below. Leave the screws loose enough to allow for movement of the lower support. Upper Support Lower Support Wall Mount 5. Align the vacant screw holes on the lower support with the ones on the upper support, and insert a No. 8-32 × 1" security hex screw in each side. NOTE: The location of the vacant holes differs between the proj
ملخص المحتوى في الصفحة رقم 12
6. Tighten all the screws that attach the upper and lower supports to the wall mount. 7. Hang the assembled projector mount on the four wall screws, pushing the mount down firmly so the keyholes fit snugly on the protruding screws. 8. Thread the remaining 1/4-20 × 2" security hex screws into the two vacant wall anchors. 9. Using the 5/32" security hex key, tighten the six wall screws. IMPORTANT If you’re installing the projector mount on drywall, it’s important not to overtighten the wall scre
ملخص المحتوى في الصفحة رقم 13
11. Position the combined brackets over the posts on the wall mount, and use three acorn nuts to secure them. Attaching the Projector Plate to the Projector 1. Close and lock the projector’s mirror cover. 2. Turn the projector over. 3. Remove the projector’s feet. 4. Align the projector plate with the feet position, and replace the feet. The feet attach the projector plate to the bottom of the projector. Projector Feet (×4) Projector Plate PMWT-660/680 Installation Guide 11
ملخص المحتوى في الصفحة رقم 14
5. Insert the four No. 8-32 × 1" TORX screws through the four small holes in the projector plate, and anchor them in the projector’s matching screw holes by hand until they are snug. Then, using the supplied TR20 TORX security hex key, tighten the screws another half turn. CAUTION Do not overtighten these screws, and do not use a power tool to insert them. If you do, you could damage your projector. These screws are not the main attachment between the projector and the projector plate. They
ملخص المحتوى في الصفحة رقم 15
2. Attach the projector plate to the projector bracket by inserting a No. 8-32 × 1/2" security hex screw through the projector plate’s slot and into the projector bracket’s screw hole. Don’t tighten the screw completely. Insert it only until the threads of the screw become visible on the inside of the projector bracket. Slot in Projector Plate 3. Repeat this process for the three remaining screws. TIP If you insert the next screw in the projector’s diagonally opposite corner, your assistant
ملخص المحتوى في الصفحة رقم 16
2. Center the interactive whiteboard on the wall mount bracket by measuring the distances between the edges of the interactive whiteboard and the wall mount bracket. Move the interactive whiteboard to the left or right until it’s centered. Move the interactive whiteboard left or right on the wall mount bracket until these distances are the same 3. Push the center tab of each pen tray bracket so it’s flush with the wall. 4. Use a pencil to mark the location of the holes in the pen tray tabs.
ملخص المحتوى في الصفحة رقم 17
9. Slide the pen tray onto its support brackets until the pen tray rests snugly against the bottom of the interactive whiteboard frame. Click the pen tray into place. 10. Route the MOD6 cable through the cable management channel and insert the connector into port 1. 11. Connect the interactive whiteboard to your computer. Consult the installation instructions that came with your interactive whiteboard for details. Routing the Projector Cables Run the projector’s cables up through the gap betw
ملخص المحتوى في الصفحة رقم 18
Finally, route the cables behind the interactive whiteboard. NOTES • The cables supplied with the NEC WT600 or WT610 projector are unlikely to be long enough to reach the power outlet and the computer. You must purchase longer cables if you need them. • Make sure the cables are not caught between the wall and those portions of the interactive whiteboard that touch the wall. Adjusting the Projected Image on the Interactive Whiteboard NOTE: Don’t adjust the projected image until after you’ve
ملخص المحتوى في الصفحة رقم 19
Customer Support Online Support Visit www.smarttech.com/support to view and download user’s guides, “how-to” and troubleshooting articles, software and more. Training Visit www.smarttech.com/trainingcenter for training materials and information about our training services. Contacting SMART Technical Support SMART Technical Support welcomes your call. However, if you experience difficulty with your SMART product, you may want to contact your local reseller first. Your local reseller may be abl
ملخص المحتوى في الصفحة رقم 20
Warranty Product warranty is governed by the terms and conditions of SMART’s “Limited Equipment Warranty” that shipped with the SMART product at the time of purchase. Registration To help us serve you, register online at www.smarttech.com/registration. 18 PMWT-660/680 Installation Guide
