ملخص المحتوى في الصفحة رقم 1
SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
PELLET STOVE
Mini
OWNER’S MANUAL
PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE
OF THIS PELLET-BURNING ROOM HEATER. FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY
OR EVEN DEATH.
Contact your building or fire officials about restrictions and installation
inspection requirements in your area
ملخص المحتوى في الصفحة رقم 2
Table of Contents Introduction..............................................................................................................3 Pellet Quality..................................................................................................3 Important Safety Data....................................................................................4 Safety Warnings And Recommendations...........................................................4 Rating Label Location................
ملخص المحتوى في الصفحة رقم 3
Introduction * This manual is designed for the home owner in conjunction with the technical manual. * PELLET QUALITY: Pellet quality is important, please read the following: Your enviro pellet stove has been designed to burn wood pellets only. Do not use any other type of fuel, as this will void any warranties stated in this manual. The performance of your pellet stove is greatly affected by the type and quality of wood pellets being burned. As the heat output of various quality wood pellets d
ملخص المحتوى في الصفحة رقم 4
Introduction IMPORTANT SAFETY DATA: Please read the entire Technical and Owner’s Manual before installing or operating your ENVIRO Pellet Stove. Failure to follow these instructions may result in property damage, bodily injury or even death. Contact your local building or fire official to obtain a permit and any information on installation restrictions and inspection requirements for your area. To prevent the possibility of a fire, ensure that the appliance is properly installed by adhering
ملخص المحتوى في الصفحة رقم 5
Introduction ASHES: Disposed ashes should be placed in a metal container with a tight-fitting lid. The closed container of ashes should be on a non-combustible floor on the ground, well away from all combustible materials pending final disposal. The ashes should be retained in the closed container until all cinders have thoroughly cooled before disposing of them. ELECTRICAL: The use of a surge protected power bar is recommended. The unit must be grounded. The grounded electrical cord should
ملخص المحتوى في الصفحة رقم 6
Introduction RATING LABEL LOCATION: The rating label is located on the back of the unit. APPLIANCE DIMENSIONS AND SPECIFICATIONS: 1 1 5 / 2 " ( 3 9 3 m m ) Weight (with full hopper): 238 lb (108 Kg) Hopper Capacity: up to 48 lb (21.8 Kg) Voltage: 110 - 120 V Max Current: 4.1 Amps Consumption on High: 3.1 lb/hr (1.4 Kg/hr)* Consumption on Low: 1.3 lb/hr (0.6 Kg/hr)* (Note: Consumption will vary with the type of fuel used.) 7 7 1 7 / 8 " 1 8 / 8 " ( 45 5 m m ) ( 48 1 m m ) 34 " ( 864 m m ) 5 1 17
ملخص المحتوى في الصفحة رقم 7
Operating Instructions AUTOMATIC SAFETY FEATURES OF YOUR PELLET STOVE: Your pellet Stove has the following safety features: A. The stove will shut off when the fire goes out and the exhaust temperature drops below 120°F (49°C). B. The stove has a high temperature safety switch. If the temperature on the hopper reaches 200°F (93°C), the auger will automatically stop and the stove will shut down when the exhaust temperature cools. If this happens, call your local dealer to reset the 200°F (93°
ملخص المحتوى في الصفحة رقم 8
Operating Instructions OPERATING YOUR PELLET STOVE: PRE-BURN INSTRUCTIONS: The burn pot liner holes must be clear and the liner installed properly against the ignitor tube for proper operation. Check the hopper for enough pellets to start the unit. DO NOT OPERATE THE UNIT WITH THE DOOR OR ASH PAN OPEN. MANUAL MODE: To START: Press the ON / OFF button. The stove will turn on. The system light will flash. The Auger Light will flash with each pulse of the auger (the Auger Feed Rate is pre-pro
ملخص المحتوى في الصفحة رقم 9
Operating Instructions SLIDER/DAMPER SET-UP: S l i d e r D am per E x haust C hannel E x haust B l o w er Figure 4: Slider/Damper Plate in Unit. If the fire should happen to go out and the heat output indicator has been set on the lowest setting, the Slider Damper may need to be adjusted, decreasing the air in the firebox or adjust the auger trim. If, after long periods of burning, the fire builds up and over flows the burn pot or there is a build up of clinkers, this would be a sign that the
ملخص المحتوى في الصفحة رقم 10
Routine Cleaning and Maintenance The following list of components should be inspected and maintained routinely to ensure that the appliance is operating at its’ optimum and giving you excellent heat value: 2-3 Days / Weekly Semi-annually or 2 Tons of Fuel B ur n P o t L i n e r Burn Pot and Liner Exhaust Vent Heat Exchanger Tubes Air Intake Ash Pan Blower Mechanisms Door Glass Heat Exchanger Tubes A i r I n t a k e T ub e Inside Firebox Behind Firebox Liners & Covers Ash Pan and Door Gaskets Al
ملخص المحتوى في الصفحة رقم 11
Routine Cleaning and Maintenance If the glass has build up that can not be removed with only the cloth, clean the glass using paper towel and a gas appliance glass cleaner, this may be purchased through most dealers. If a gas appliance glass cleaner is not available, use a damp paper towel dipped in fly ash to clean the glass. After the glass has been cleaned use the dry soft cloth to wiping down the outside and inside of the glass. H eat e xc h a ng er tubes ASH PAN (weekly) cl eane r ha nd
ملخص المحتوى في الصفحة رقم 12
Routine Cleaning and Maintenance Removal of the firebox backing. • Open the door by lifting the handle, remove the burn pot and burn pot liner. • Lubricate all screws with penetrating oil. • Remove the four (4) screws that hold the side panels in place. • With the tip of a flat screwdriver, gently lift up the side panels and remove the side panels. • Pull the center panel out. • Vacuum thoroughly. Installation of firebox backing: • Insert center panel. • Place the side panels back into the fire
ملخص المحتوى في الصفحة رقم 13
Warranty Sherwood Industries Ltd. gives a five year limited warranty on all steel manufactured parts. A one-year warranty is provided on all electrical components. The above limited warranties are extended only to the original purchaser. There is no warranty on the following parts: ● Glass window ● Fiberglass rope gaskets ● refractory material ● burn pot liner ● paint ● enamel finish or gold plating where it applies **NOTE: The paint on the brick firebox lining may peel. This is due to the e
ملخص المحتوى في الصفحة رقم 14
Installation Data Sheet The following information must be recorded by the installer for warranty purposes and future reference. NAME OF OWNER: NAME OF DEALER: _________________________________________ _________________________________________ ADDRESS: ADDRESS: _________________________________________ _________________________________________ _________________________________________ _________________________________________ _________________________________________ _____________________________
