ملخص المحتوى في الصفحة رقم 1
INSTALLATION
INSTRUCTIONS
STANDARD SERIES
UVFC-600
36" & 42" Unvented Fireboxes
P/N 700,018M REV. C 12/2003
MODELS
UVFR-500 UVFC-500
UVFR-600 UVFC-600
UVFR-500
FOR USE ONLY WITH DECORATIVE TYPE UNVENTED ROOM
HEATERS.
DO NOT BUILD A WOOD FIRE.
RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE
WARNING: IMPROPER INSTALLATION, ADJUSTMENT, AL-
TERATION, SERVICE OR MAINTENANCE CAN CAUSE IN-
JURY OR PROPERTY DAMAGE. REFER TO THIS MANUAL.
FOR ASSISTANCE OR ADDITIONAL INFORMATION CON-
SULT A QUALIFIED IN
ملخص المحتوى في الصفحة رقم 2
Check the inventory list to be sure that you have TABLE OF CONTENTS GENERAL INFORMATION all the necessary parts in usable condition. Also check for concealed damage. These ventless firebox enclosures are designed Firebox/Log Set Reference Chart ..... page 2 to accept all ANSI Z21.11.2 approved Decora- General Information ......................... page 2 tive Type Unvented Gas Log Room Heaters. Inventory Inventory ......................................... page 2 For the appropriate Unvented Gas L
ملخص المحتوى في الصفحة رقم 3
Carbon Monoxide Poisoning: Early signs of • Ensure that the heater is clean when operat- Use the following equations to determine if ing. Excessive dust accumulation on the burner you have a confined or unconfined space. carbon monoxide poisoning are similar to the and logs will increase the amount of carbon flu with headaches, dizziness and/or nausea. 3 If you have these signs, obtain fresh air im- monoxide formation and could lead to carbon 1. Determine the volume of space — ft . monoxide pois
ملخص المحتوى في الصفحة رقم 4
• Never obstruct the front opening of the un- Clearances WARNING: IF THE AREA IN WHICH THE vented firebox or restrict the flow of combus- HEATER MAY BE OPERATED IS SMALLER tion and ventilation air. WARNING: DO NOT INSTALL THESE THAN THAT DEFINED AS AN UNCON- BUILT-IN UNVENTED FIREBOXES IN FINED SPACE, PROVIDE ADEQUATE • Minimize modifications to existing construc- SLEEPING QUARTERS, OR IN RECRE- COMBUSTION AND VENTILATION AIR BY tion. See Figure 1 for location suggestions. ATIONAL VEHICLES. ON
ملخص المحتوى في الصفحة رقم 5
Install only a ¹⁄₂" (1 ¹⁄₂" max.) inside diameter Note: The following steps represent the nor- Safe Zone mal sequence of installation. Each installation approved gas line through the firebox wall for Finished is unique, however, and might require a differ- connection to the unvented room heater inside 8" Wall Max. the firebox. ent sequence. 3" Ensure that a sediment trap is installed in the Step 1. Position firebox prior to framing or Header into prepared framing. existing gas line, if not, ins
ملخص المحتوى في الصفحة رقم 6
Firebox Framing UVF-500 SPECIFICATIONS Construct firebox framing following Figures 6 through 8 and the chart on page 8 for your 9 ⁵⁄₈" specific installation requirements. Refer to 7 ¹⁄₂" (244 mm) Figures 4 and 5 on pages 6 and 7 for firebox (191 mm) dimensions. The firebox may be installed directly on a com- 36" (914 mm) bustible floor or raised on a platform of an 37" (940 mm) appropriate height. Do not place firebox on 20 ³⁄₁₆" (513 mm) carpeting, vinyl or other soft floor coverings. It 27 ⁷⁄
ملخص المحتوى في الصفحة رقم 7
Firebox Installation UVF-600 SPECIFICATIONS Note: The firebox must be installed giving full 8 ³⁄₈" (213 mm) consideration to the clearance and height re- 13 ³⁄₈" quirements identified in this manual. (340 mm) Step 1. Slide the firebox into prepared framing or position firebox in its final position and frame later. 41" (1041 mm) 43" (1092 mm) Step 2. Refer to firebox and framing specifica- 22 ⁵⁄₁₆" 2" 29 ⁵⁄₈" tions on pages 6, 7and 8 Figures 6 through 10 (566 mm) (51 mm) (752 mm) for framing dim
ملخص المحتوى في الصفحة رقم 8
FRAMING SPECIFICATIONS Header Framing Dimensions B Opening UVF-500 UVF-600 A 41 ¹⁄₄" 46 ¹⁄₄" A B 37 ¹⁄₂" 43 ¹⁄₂" Figure 6 C 27 ¹⁄₂" 31 ³⁄₄" D 13 ³⁄₄" 15 ⁷⁄₈" E 66 ³⁄₄" 73" Back Wall Of Chase/Enclosure Including Finishing Materials F 33 ³⁄₈" 36 ¹⁄₂" If Any G 19 ⁵⁄₈" 20 ⁵⁄₈" D H 47 ¹⁄₄" 51 ⁵⁄₈" F H G C A E Rough Framing Face (Unfinished Shown) Corner Installation Figure 7 Rough Framing Face Back Wall Of Chase/Enclosure (Unfinished Shown) Including Finishing Materials If Any C G A Figure 8 8 NOTE:
ملخص المحتوى في الصفحة رقم 9
Step 2. Align the canopy with the holes in the Blower Kit Installation top frame. To install the blower kit, follow Steps 1 thru 5 Step 3. Replace the screws previously removed. and refer to Figures 12, 13 and 14. Step 4. Tighten side screws. Make sure the Step 1. Locate the blower motor shield. canopy is level and secure. Step 2. Remove the motor shield by bending it OPTIONAL EQUIPMENT along the perforation until the tabs break away. 8d Nail Step 3. With the motor shield removed, place Blower
ملخص المحتوى في الصفحة رقم 10
FIREBOX FINISHES ACCESSORIES AND COMPONENTS There are a wide variety of “finished looks” for (FBK-200 Models Only) your built-in unvented firebox from formal wall decor with elaborate mantels to rustic wood paneling or warm brick facings. Only noncombustible materials like marble, stone, tile, brick, etc. may overlap the black front facing but be sure not to block the upper or lower grilles. Seal all joints between the black facing and wall surrounds to prevent air intru- Blower Kits sion. Use n
ملخص المحتوى في الصفحة رقم 11
REPLACEMENT PARTS 3 2 4 1 UVFR-600 5 3 4 6 5 UVFR-500 UVF-500 UVF-600 No. DESCRIPTION Part No. Qty. Part No. Qty. Gas Fireplace Assembly – – – – 1. Firescreen 36L89 2 36L99 2 2. Rod, Screen 88L95 2 88L96 2 3. Refractory, Side 88L59 2 88L65 2 4. Refractory, Rear 88L58 1 88L64 1 5. Refractory Base 88L57 1 88L63 1 6. Canopy 96L27 1 96L28 1 NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 11
ملخص المحتوى في الصفحة رقم 12
The manufacturer reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information. Printed in U.S.A. © 2000 by LHP Manufactured By LHP P/N 700,018M REV. C 12/2003 1110 West Taft Avenue • Orange, CA 92865
