ملخص المحتوى في الصفحة رقم 1
DO NOT
DISCARD
Owner’s Manual
Installation and Operation
Models:
SL-750TRS-IPI-E
SL-550TRS-IPI-E
SL-350TRS-D
SL-350TRS-IPI
CAUTION
DO NOT DISCARD THIS MANUAL
• Important operating • Read, understand and follow • Leave this manual with
and maintenance these instructions for safe
party responsible for use
instructions included. installation and operation.
and operation.
WARNING
WARNING: If the information in these
HOT! DO NOT TOUCH.
instructions is not followed exactly, a fi re
SEVERE BUR
ملخص المحتوى في الصفحة رقم 2
Read this manual before installing or operating this appliance. Please retain this owner’s manual for future reference. Congratulations Congratulations on selecting a Heat & Glo gas appliance This Owner’s Manual should be retained for future —an elegant and clean alternative to wood burning reference. We suggest that you keep it with your other important documents and product manuals. appliances. The Heat & Glo gas appliance you have selected is designed to provide the utmost in safety, The
ملخص المحتوى في الصفحة رقم 3
Table of Contents 1 Listing and Code Approvals 9 Gas Information A. Appliance Certifi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 A. Fuel Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 B. Glass Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. Gas Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 C. BTU Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 C. G
ملخص المحتوى في الصفحة رقم 4
Listing and Code Approvals 1 1 A. Appliance Certifi cation C. BTU Specifi cations Models Maximum Minimum Orifi ce MODELS: SL-750TRS-IPI-E,SL-550TRS-IPI-E, U.S. (0-2000 ft.) or Input Input Size SL-350TRS-D, SL-350TRS-IPI Canada (2000-4500 ft.) BTU/h BTU/h (DMS) LABORATORY: Underwriters Laboratories, Inc. (UL) U.S. 30,800 20,200 #37 SL-750TRS-IPI-E (NG) TYPE: Direct Vent Gas Appliance Heater Canada 27,720 18,180 #38 U.S. 30,700 23.300 #52 STANDARD: ANSI Z21.88a-2007 • CSA 2.33a-2007 S
ملخص المحتوى في الصفحة رقم 5
Inspection Note: The following requirements reference various The state or local gas inspector of the side wall horizon- Massachusetts and national codes not contained in this tally vented gas fueled equipment shall not approve the document. installation unless, upon inspection, the inspector ob- serves carbon monoxide detectors and signage installed G. Requirements for the Commonwealth of in accordance with the provisions of 248 CMR 5.08(2)(a)1 Massachusetts through 4. For all side wall
ملخص المحتوى في الصفحة رقم 6
Getting Started 2 2 A. Design and Installation Considerations C. Inspect Appliance and Components Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of WARNING the building and all exhaust gases expelled to the out- Inspect appliance and components for damage. side. No additional outside air source is required. Damaged parts may impair safe operation. • Do NOT install damaged components. • Do NOT install incomplete components. CAUTIO
ملخص المحتوى في الصفحة رقم 7
Framing and Clearances 3 3 Note: WARNING • Illustrations reflect typical installations and are FOR Fire Risk DESIGN PURPOSES ONLY. Provide adequate clearance: • Illustrations/diagrams are not drawn to scale. • Around air openings • Actual installation may vary due to individual design preference. • To combustibles • For service access A. Selecting Appliance Location Locate appliance away from traffi c areas. When selecting a location for your appliance it is important to NOTE: For actual
ملخص المحتوى في الصفحة رقم 8
insulation. If the appliance is being installed on a cement B. Constructing the Appliance Chase slab, a layer of plywood may be placed underneath to pre- A chase is a vertical boxlike structure built to enclose the vent conducting cold up into the room. gas appliance and/or its vent system. Vertical vents that run on the outside of a building may be, but are not re- C. Clearances quired to be, installed inside a chase. Construction of the chase may vary with the type of build- WARNING ing. Th
ملخص المحتوى في الصفحة رقم 9
D. Elevated Hearth Systems Use the table below to identify the hearth system that will be used. The table will also help identify effects on the various dimensions. Some hearth systems will elevate the appliance off the fl oor at a given dimension. For example, if appliance will be used with a Kenwood Cabinet with Base, the appliance will be elevated 9-1/4 inches. The 9-1/4 inch elevation will also have to be added to the following: Extension Wall Hole referenced in Figure 6.3 (Exterior W
ملخص المحتوى في الصفحة رقم 10
E. Mantel Projections All measurements are in inches. CEILING 1/2 IN. MINIMUM 12 11 10 9 2-7/8 IN. 8 7 32 MINIMUM 3 FT. MAXIMUM 6 5 Note: Clearance from opening 13 4 12 to perpendicular wall. 11 3 10 9 8 7 6 5 4 Figure 3.5 Clearances to Mantel Legs or Wall Projections (Acceptable on both sides of opening.) TOP OF HOOD OR FIREPLACE OPENING Figure 3.3 Clearances to mantels or other combustibles above appliance 1/2 in. SHEETROCK 3-1/2 in. NON-COMBUSTIBLE 3 IN. BOARD SHIPPED MINIMUM WITH AP
ملخص المحتوى في الصفحة رقم 11
Termination Locations 4 4 HORIZONTAL A. Vent Termination Minimum Clearances OVERHANG 2 FT. 20 INCHES MIN. WARNING VERTICAL MIN. WALL LOWEST Fire Risk. DISCHARGE OPENING Explosion Risk. GAS DIRECT VENT TERMINATION CAP Maintain vent clearance to combustibles as specifi ed. X 12 • Do not pack air space with insulation or other materials. ROOF PITCH IS X/ 12 Failure to keep insulation or other materials away from vent pipe may cause fi re. H (MIN.) - MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHAR
ملخص المحتوى في الصفحة رقم 12
M N P R Q (See Note 2) V T S S Electrical V V Service D* V = VENT TERMINAL X V = AIR SUPPLY INLET = AREA WHERE TERMINAL IS NOT PERMITTED A = 12 inches.................clearances above grade, veranda, L** = 7 ft. ......................... clearance above paved (See Note 1) (See Note 1) porch, deck or balcony sidewalk or a paved driveway located on public property B = 12 inches.................clearances to window or door M*** = 18 inches................ clearance under veranda, porch, that
ملخص المحتوى في الصفحة رقم 13
Vent Information and Diagrams 5 5 A. Vent Table Key The abbreviations listed in this vent table key are used in the vent diagrams. Symbol Description Vertical First section (closest to appliance) of vertical length V1 Second section of vertical length V2 First section (closest to appliance) of horizontal length H1 8-1/2 in. Second section of horizontal length H2 WARNING Horizontal Fire Hazard. Explosion Risk. Figure 5.1 Asphyxiation Risk. Do NOT connect this gas appliance to a chimney fl ue
ملخص المحتوى في الصفحة رقم 14
D. Use of Flex Vent The fl ex vent must be supported with TERMINATION the spacing between support intervals CAP 3in. CLEARANCE not exceeding 4 feet, with no more than ½ inch sag between supports. A support is required at each change in venting direction, and in any location where it is necessary to maintain the necessary clearance to combustibles. FLEX-VENT A simple “up and out” installation (Fig- ure 5.3) requires only enough support to maintain the necessary clearance 1in. to combustib
ملخص المحتوى في الصفحة رقم 15
E. Vent Diagrams WARNING Fire Risk. Explosion Risk. Do NOT pack insulation or other combustibles between ceiling fi restops. • ALWAYS maintain specifi ed clearances around venting and fi restop systems. • Install wall shield and ceiling fi restops as specifi ed. Failure to keep insulation or other material away from vent pipe may cause fi re. 1. Top Vent - Horizontal Termination Venting H Maximum 1 V Minimum One Elbow SL-350TRS-D SL-550, SL-750TRS-E 90º Elbow 1-1/2 ft. 457 mm 1 ft. 305 mm Note: Use
ملخص المحتوى في الصفحة رقم 16
Two Elbows H Maximum V Minimum Note: Use SL-D Series SL-350TRS-D, SL-550TRS-E, SL-750TRS-E components only. 90º Elbow NOT ALLOWED 1/2 ft. 152 mm 1 ft. 305 mm 1-1/2 ft. 457 mm 2 ft. 610 mm Note: There MUST be a 25% reduction in total H when using 2-1/2 ft. 762 mm 4 ft. 1.2 m fl ex vent except when using the 3-1/2 ft. 1.1 m 6 ft 1.8 m simple up and out installation 4-1/2 ft. 1.4 m 14 ft. 4.3 m (see Figure 5.3). H + H Maximum= 14 ft. (4.3 m) 1 2 V + H + H Maximum= 40 ft. (12.2 m) 1 1 2 WARNING
ملخص المحتوى في الصفحة رقم 17
1. Top Vent - Horizontal Termination - (continued) H Maximum H + H Maximum H Maximum H + H Maximum 1 1 2 1 1 2 V Minimum Three Elbows 1 Model: SL-350TRS-D Models: SL-550TRS-IPI-E, SL-750TRS-IPI-E Elbow only 1-1/2 ft. 457 mm 2 ft. 610 mm 1 ft. 305 mm 2 ft. 610 mm 1/2 ft. 152 mm 2 ft. 610 mm 4 ft. 1.2 m 2 ft. 610 mm 4 ft. 1.2 m 1-1/2 ft. 457 mm 3 ft. 914 mm 6 ft. 1.8 m 3 ft. 914 mm 6 ft. 1.8 m 2-1/2 ft. 762 mm 5 ft. 1.5 m 10 ft 3.0 m 5 ft. 1.5 m 10 ft. 3.0 m 3-1/2 ft. 1.1 m 7 ft. 2.1 m 14 ft. 4.
ملخص المحتوى في الصفحة رقم 18
Exhaust restrictor Instructions 2. Top Vent - Vertical Termination 1. Install the exhaust restrictor over the center of the ex- haust outlet in the fi rebox (see Figure 5.8). No Elbow 2. Center the exhaust restrictor in the open end of the exhaust outlet and secure through the slots on the ex- Note: Use SL-D Series haust restrictor with the 2-1/4 in. self tapping screws components only. provided in the appliance manual bag. Note: If installing a vertical vent/termination off the top of the a
ملخص المحتوى في الصفحة رقم 19
2. Top Vent - Vertical Termination - (continued) Two 90º Elbows H Maximum H Maximum V V + V Minimum 1 1 2 1 2 V Minimum 1 SL-350TRS-D SL-550TRS-E, SL-750TRS-E * * 90º Elbow 1-1/2 ft. 457 mm 1 ft. 305 mm * * 1/2 ft. 152 mm 2 ft. 610 mm 2 ft. 610 mm * * 1 ft. 305 mm 2-1/2 ft. 762 mm 2-1/2 ft. 762 mm * * 2 ft. 610 mm 4 ft. 1.2 m 4 ft. 1.2 m * * 3 ft. 914 m 6 ft. 1.8 m 6 ft. 1.8 m * * 4 ft. 1.2 m 8 ft. 2.4 m 8 ft. 2.4 m * * 5 ft. 1.5 m 15 ft. 4.6 m 15 ft 4.6 m * * H Maximum= 15 ft. (4.6 m) 1 V +
ملخص المحتوى في الصفحة رقم 20
2. Top Vent - Vertical Termination - (continued) Three 90º Elbows ALL MODELS Note: Use SL-D Series V H + H Maximum V V + V Minimum 1 1 2 2 1 2 components only. 90º Elbow 0 0 1-1/2 ft. 457 mm 1-1/2 ft. 457 mm 1/2 ft.. 152 mm 1 ft. 305 mm * * * * Note: There MUST be a 25% 1-1/2 ft. 457 mm 2 ft. 610 mm * * * * reduction in total H when using 2-1/2 ft. 762 mm 4 ft. 1.2 m * * * * fl ex vent except when using the simple up and out installation 3-1/2 ft. 1.1 m 6 ft. 1.8 m * * * * (see Figure
