ملخص المحتوى في الصفحة رقم 1
DO NO DO NO DO NOT T T
DO NO DO NOT T
DISCARD DISCARD DISCARD
DISCARD DISCARD
Owner’s Manual
Installation and Operation
Model:
ST-42TVFL-IPI
CAUTION
DO NOT DISCARD THIS MANUAL
Important operating Read, understand and follow Leave this manual with
• ••
and maintenance these instructions for safe party responsible for
instructions included. installation and operation. use and operation.
WARNING
WARNING: If the information in these
HOT SURFACES!
instructions is not followed exactly, a fire
Glass
ملخص المحتوى في الصفحة رقم 2
SAFETY AND WARNING INFORMATION READ and UNDERSTAND all instructions carefully before starting the installation. ! FAILURE TO FOLLOW these installation instructions may result in a possible fire hazard and will void the warranty. Prior to the first firing of the fireplace, READ the Using Your Fireplace section of the ! Owners Guide. DO NOT USE this appliance if any part has been under water. Immediately CALL a ! qualified service technician to inspect the unit and to replace any part of the contr
ملخص المحتوى في الصفحة رقم 3
Safety and Warning Information .................. 2 Service Parts List ......................................... 4 Section 1: Approvals and Codes ................ 6 Appliance Certification........................................... 6 Installation Codes .................................................. 6 Table of High Altitude Installations ....................................... 6 Contents Section 2: Getting Started............................ 7 Introducing the Heat & Glo Gas Fireplaces ......
ملخص المحتوى في الصفحة رقم 4
ST-42TVFL-IPI Service Parts Service Parts Diagram Beginning Manufacturing Date: July 2002 Ending Manufacturing Date: _______ 6 1 Log Set Assembly 2 3 4 5 7 IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed Stocked in this manual may be ordered from an authorized dealer. at Depot ITEM DESCRIPTION SERIAL # PART NUMBER LOGS-MS Log Set Assembly (sold as complete log set only) Y 45
ملخص المحتوى في الصفحة رقم 5
ST-42TVFL-IPI Service Parts Valve Assembly Diagram/Parts List Beginning Manufacturing Date: July 2002 Ending Manufacturing Date: ______ IPI Valve Assembly 1 2 3 4 5 6 7 10 8 9 11 12 13 16 14 15 IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed Stocked in this manual may be ordered from an authorized dealer. at Depot ITEM DESCRIPTION SERIAL # PART NUMBER 385-510A Pilot Assembly N
ملخص المحتوى في الصفحة رقم 6
Approval Listings Appliance Certification The Heat & Glo fireplace models discussed in this and Codes Installers Guide have been tested to certification standards and listed by the applicable laboratories. CERTIFICATION MODEL LABORATORY TYPE STANDARD 1 ST-42TVFL-IPI Underwriters B- Vent ANSI Z21.50•CGA2.22 Approvals and Codes Installation Codes The fireplace installation must conform to local codes. Before installing the fireplace, consult the local building code agency to ensure that you
ملخص المحتوى في الصفحة رقم 7
Introducing the Heat & Glo B-type vent gas fireplaces are designed to operate with all exhaust gases expelled to the outside Heat & Glo of the building. Gas Fireplaces The information contained in this Installers Guide, unless noted otherwise, applies to all models and gas control systems. Gas fireplace diagrams, including the dimensions, are 2 shown in this section. Getting Pre-installation This gas fireplace and its components are tested and Started safe when installed in accordance with thi
ملخص المحتوى في الصفحة رقم 8
When planning a fireplace installation, it’s necessary to determine: • Where the unit is to be installed. • The vent system configuration to be used. • Gas supply piping. • Electrical wiring. • Framing and finishing details. • Whether optional accessories—devices such as a fan, wall switch, or remote control—are desired. If the fireplace is to be installed on carpeting or tile, or on any combustible material other than wood flooring, the fireplace should be installed on a metal or wood panel tha
ملخص المحتوى في الصفحة رقم 9
Step 1 The diagram below shows space and clearance requirements for locating a fireplace within a room. Locating the Fireplace TOP 3 VIEW Installing the Fireplace 36" GLASS 1" GLASS 36" Figure 3. Fireplace Locations and Space Requirements Clearance Requirements The top, back, and sides of the fireplace are defined by stand-offs. Minimum Clearances from the Fireplace to Combustible Materials Glass Back of Metal Ends Top of Sides Floor Fireplace of Fireplace Fireplace Ceilin
ملخص المحتوى في الصفحة رقم 10
Minimum Clearances from the B-Type Vent Pipe to Combustible Materials is 1 inch (25 mm) all around the pipe. Step 2 Fireplace framing can be built before or after the fireplace is set in place. Framing should be Framing the positioned to accommodate wall coverings and Fireplace fireplace facing material. The diagram below shows framing reference dimensions. CAUTION MEASURE FIREPLACE DIMENSIONS, AND VERIFY FRAMING METHODS AND WALL COVERING DETAILS, BEFORE FRAMING CONSTRUCTION BEGINS. ST-42TVFL-IP
ملخص المحتوى في الصفحة رقم 11
Negative Pressure warning: When negative pressure Step 3 is present, an atmospherically vented fireplace (with a Negative draft hood) may not function properly and it may down Pressure draft. In the case of a gas appliance, spillage of the combustion gases may occur. This may create a Make-up Air dangerous carbon monoxide situation in the house. The causes of negative pressure to a house can include the following: • Stack effect in the building. • Exhaust only appliances (mechanically and atmo
ملخص المحتوى في الصفحة رقم 12
Detailed installation instructions for Model AK-TV Outside Air kit are found in the kit. Air Damper Before lighting the burner, open the damper plate by sliding the air damper rod, located by the gas valve, towards you. DUCT COLLAR DAMPER ASSEMBLY Figure 5. Make-up Air 12 Heat & Glo • ST-42TVFL-IPI • 455-902 Rev. C • 12/07
ملخص المحتوى في الصفحة رقم 13
Step 4 A. Vent System Approvals Installing the These fireplaces are approved to use 6-inch (152mm) diameter B-type vent. B-type vent must be used Vent System when the vent system is within combustible construction. These models may also use single wall rigid or flexible gas vent IF and ONLY IF the vent system is installed within non-combustible construction such as a masonry chimney. The same diameters noted above for B-type vent must be used for single-wall vent. See Figure 6. The flame and e
ملخص المحتوى في الصفحة رقم 14
4 FT. MINIMUM MAXIMUM HORIZONTAL RUN 17 FT. MAXIMUM 10 FT. MINIMUM 4 FT MINIMUM Figure 6. Vent System Attachment WARNING: THIS GAS FIREPLACE ! MUST NEVER BE VENTED BY CONNECTING TO A CHIMNEY FLUE SERVING A SEPARATE SOLID FUEL BURNING APPLIANCE. 14 Heat & Glo • ST-42TVFL-IPI • 455-902 Rev. C • 12/07
ملخص المحتوى في الصفحة رقم 15
C. Bedroom Installation in Canada This model MUST NOT be vented into a vent system installed exterior to a building. The part of the vent system above the roof line can be exterior to the building. D. Vent Termination WARNING: MAJOR U.S. BUILDING ! CODES SPECIFY MINIMUM CHIMNEY AND/OR VENT HEIGHT ABOVE THE ROOF TOP. THESE MINIMUM HEIGHTS ARE NECESSARY IN THE INTEREST OF SAFETY. FIGURE 7 AND TABLE SHOW MINIMUM HEIGHTS, PROVIDED THE TERMINATION CAP IS AT LEAST 8-FEET FROM A VERTICAL WALL. NOTE:
ملخص المحتوى في الصفحة رقم 16
Step 5 Positioning, The diagram below shows how to properly position, level, and secure the fireplace. Leveling, and Securing the Fireplace 1. Place the fireplace into position. 2. Level the fireplace from side to side and from front to back. 3. Shim the fireplace with non-combustible material, such as sheet metal, as necessary. 4. Secure the fireplace to the framing by nailing or screwing. NAILING TABS AT BASE OF FIREPLACE. Figure 8. Proper Positioning, Leveling, and Securing of a Fireplace Ste
ملخص المحتوى في الصفحة رقم 17
Step 7 NOTE: Have the gas supply line installed in accordance with local building codes by a The Gas qualified installer approved and/or licensed as Supply Line required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter). NOTE: Before the first firing of the fireplace, the gas supply line should be purged of any trapped air. NOTE: Consult local building codes to properly size the gas supply line leading to the 1/2 inch (13 m
ملخص المحتوى في الصفحة رقم 18
• At the gas line access hole, use insulation to re- pack the space around the gas pipe. • Insert insulation from the outside of the fireplace and pack the insulation tightly to totally seal between the pipe and the outer casing. The gas line should be installed by a qualified service technician. USE A WRENCH ON SHUT-OFF VALVE WHEN TIGHTENING GAS LINE MANUAL SHUT-OFF VALVE GAS VALVE GAS LINE ACCESS FLEX CONNECTOR Figure 9. Gas Supply Line Step 8 Pressure requirements for Heat & Glo gas firepla
ملخص المحتوى في الصفحة رقم 19
Step 9 NOTE: Electrical wiring must be installed by a licensed electrician. Wiring the Caution: Disconnect remote controls if you are Fireplace absent for extended time periods. This will prevent accidental fireplace operation. Appliance Requirements • This appliance DOES NOT require 110-120 VAC to operate. WARNING ! DO NOT CONNECT 110-120 VAC TO THE GAS CONTROL VALVE WALL SWITCH OR THE APPLIANCE WILL MALFUNCTION AND THE VALVE WILL BE DESTROYED. Optional Accessories Optional remote control kit
ملخص المحتوى في الصفحة رقم 20
JUNCTION BOX INTERMITTENT PILOT IGNITOR IGNITION MODULE 3 VAC I S TRANSFORMER 3V BATTERY PACK WHITE ORANGE BLACK RED GROUND TO FIREPLACE CHASSIS ORANGE GREEN HI LIMIT SENSOR REMOTE RECEIVER VALVE PIGTAIL CONNECTOR *Shown with optional remote control receiver. Figure 10.Intermittent Pilot Ignition (IPI) Wiring Diagram For Intermittent Pilot Ignition (IPI) Wiring Appliance Requirements This appliance requires that 110-120 VAC be wired to the junction box. Maintain correct polarity when wiring the
