ملخص المحتوى في الصفحة رقم 1
Installers Guide
Models:
PIER-TVFL
ST-42TVFL
Underwriters
Laboratories Listed
READ THIS MANUAL BEFORE INSTALLING OR
OPERATING THIS APPLIANCE. THIS INSTALLERS
WARNING: IF THE INFORMATION
GUIDE MUST BE LEFT WITH THE APPLIANCE
IN THESE INSTRUCTIONS IS NOT
FOR FUTURE REFERENCE.
FOLLOWED EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUS-
ING PROPERTY DAMAGE, PER-
WARNING: IMPROPER INSTALLA-
SONAL INJURY, OR DEATH.
TION, ADJUSTMENT, ALTERATION,
SERVICE OR MAINTENANCE CAN
- Do not store or use gasoline or
ملخص المحتوى في الصفحة رقم 2
SAFETY AND WARNING INFORMATION READ and UNDERSTAND all instructions carefully before starting the installation. ! FAILURE TO FOLLOW these installation instructions may result in a possible fire hazard and will void the warranty. Prior to the first firing of the fireplace, READ the Using Your Fireplace section of the ! Owners Guide. DO NOT USE this appliance if any part has been under water. Immediately CALL a ! qualified service technician to inspect the unit and to replace any part of the contr
ملخص المحتوى في الصفحة رقم 3
Safety and Warning Information ....................2 u Service Parts List ...............................................4 Section 1: Approvals and Codes ................ 10 Appliance Certification ..........................................10 Table of Installation Codes .................................................10 Contents u High Altitude Installations ......................................10 Section 2: Getting Started .............................11 Introducing the Heat-N-Glo Gas Firepla
ملخص المحتوى في الصفحة رقم 4
PIER-TVFL, PIER-TVFL-DSI Service Parts (NG, LP) Exploded Parts Diagram MANUFACTURING DATES (GN, PL) Vue éclatée des pièces SP Beginning: 8-97, Ending Date: ___ DSI Beginning: 8-97, Ending Date: 3-00 u 8 6 2 1 5 4 9 3 7 Log Assembly Part number list on following page. * La liste des numéros de pièce se trouve * à la page suivante. 4
ملخص المحتوى في الصفحة رقم 5
(NG, LP) Service Parts List / Liste des pièces de rechange PIER-TVFL and PIER-TVFL-DSI IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When order- ing, supply serial and model numbers to ensure correct service parts. / IMPORTANT : L'information fournie dans cette brochure n'est valide que pendant une courte période. Les sites VIP des distributeurs disposent des renseignements les plus récents. Lors d'une commande, veuillez fournir les n
ملخص المحتوى في الصفحة رقم 6
ST-42TVFL, ST-42TVFL-DSI Service Parts (NG, LP) Exploded Parts Diagram MANUFACTURING DATES (GN, PL) Vue éclatée des pièces SP Beginning: 8-97, Ending Date: ___ DSI Beginning: 8-97, Ending Date: 8-02 u 1 3 5 1 5 4 7 2 6 Log Assembly Part number list on following page. * La liste des numéros de pièce se trouve * à la page suivante. 6
ملخص المحتوى في الصفحة رقم 7
ST-42TVFL and ST-42TVFL-DSI (NG , LP) Service Parts List / Liste des pièces de rechange IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When order- ing, supply serial and model numbers to ensure correct service parts. / IMPORTANT : L'information fournie dans cette brochure n'est valide que pendant une courte période. Les sites VIP des distributeurs disposent des renseignements les plus récents. Lors d'une commande, veuillez fournir les n
ملخص المحتوى في الصفحة رقم 8
Service Parts PIER-TVFL, ST-42TVFL (NG, LP) Exploded Parts Diagram Beginning Manufacturing Date: 10-97 (GN, PL) Vue éclatée des pièces Ending Manufacturing Date: ______ u Standing Pilot Ignition 12 Valve Assembly 4 13 10 9 5 7 1 11 2 8 3 6 u ITEM / SERIAL # PART NUMBER DESCRIPTION PIÈCE / N° DE SÉRIE / N° DE PIÈCE 1 Valve NG / Valve GN 060-522 1 Valve LP / Valve PL 060-523 2 ON/OFF Rocker Switch / Interrupteur à bascule MARCHE/ARRÊT 060-521A 3 Piezo Ignitor / Allumeur piézo 418-513
ملخص المحتوى في الصفحة رقم 9
Service Parts PIER-TVFL-DSI, ST-42TVFL-DSI MANUFACTURING DATES (NG, LP) Exploded Parts Diagram ST-42TVFL-DSI Beginning: 8-97, Ending Date: 8-02 (GN, PL) Vue éclatée des pièces PIER-TVFL-DSI Beginning: 8-97, Ending Date: 3-00 u 9 Direct Spark Ignition Valve Assembly 8 4 12 7 5 10 11 1 3 6 2 u ITEM / SERIAL # PART NUMBER DESCRIPTION PIÈCE / N° DE SÉRIE / N° DE PIÈCE 1 Junction Box / Boîtier de dérivation 100-254A 2 ON/OFF Rocker Switch / Interrupteur à bascule MARCHE/ARRÊT 060-511 3 Burne
ملخص المحتوى في الصفحة رقم 10
Approval Listings Appliance Certification The Heat-N-Glo fireplace models discussed in this and Codes Installers Guide have been tested to certification standards and listed by the applicable laboratories. CERTIFICATION MODEL LABORATORY TYPE STANDARD 1 Pier-TVFL Underwriters B- Vent ANSI Z21.50•CGA2.22 ST-42TVFL Laboratories Decorative Approvals and Codes Installation Codes The fireplace installation must conform to local codes. Before installing the fireplace, consult the local building c
ملخص المحتوى في الصفحة رقم 11
Introducing the Heat-N-Glo B-type vent gas fireplaces are designed to operate with all exhaust gases expelled to the outside Heat-N-Glo of the building. Gas Fireplaces The information contained in this Installers Guide, unless noted otherwise, applies to all models and gas control systems. Gas fireplace diagrams, including the dimensions, are 2 shown in this section. Getting Pre-installation This gas fireplace and its components are tested and Started safe when installed in accordance with thi
ملخص المحتوى في الصفحة رقم 12
When planning a fireplace installation, it’s necessary to determine: • Where the unit is to be installed. • The vent system configuration to be used. • Gas supply piping. • Electrical wiring. • Framing and finishing details. • Whether optional accessories—devices such as a fan, wall switch, or remote control—are desired. If the fireplace is to be installed on carpeting or tile, or on any combustible material other than wood flooring, the fireplace should be installed on a metal or wood panel tha
ملخص المحتوى في الصفحة رقم 13
21 5/8 (549mm) 24 1/4 (616mm) 12 1/8 (308mm) VENT COLLAR ELECTRICAL ACCESS GAS LINE 41 ACCESS (1042mm) 36 7/8 (937mm) 2 1/2 2 1/2 (64mm) (64mm) 36 1/8 (918mm) 4 (102mm) 43 (1093mm) 4 (102mm) LEFT SIDE FRONT RIGHT SIDE TOP STANDOFFS ELECTRICAL ACCESS 1/2" STANDOFFS RATING PLATE & LABELS GAS LINE GAS CONTROL VALVE ACCESS Figure 2. Diagram of the ST-42TVFL 13
ملخص المحتوى في الصفحة رقم 14
Step 1 The diagram below shows space and clearance requirements for locating a fireplace within a room. Locating the Fireplace GLASS GLASS 3 36" GLASS PIER-TVFL 36 " Installing the Fireplace TOP VIEW 36" ST-42TVFL GLASS 1" GLASS Figure 3. Fireplace Locations and Space Requirements Clearance Requirements The top, back, and sides of the fireplace are defined by stand-offs. Minimum Clearances from the Fireplace to Combustible Materials Glass Back of Metal Ends Top of Sides Fl
ملخص المحتوى في الصفحة رقم 15
Minimum Clearances from the B-Type Vent Pipe to Combustible Materials is 1 inch (25 mm) all around the pipe. Step 2 Fireplace framing can be built before or after the fireplace is set in place. Framing should be Framing the positioned to accommodate wall coverings and Fireplace fireplace facing material. The diagram below shows framing reference dimensions. MEASURE FIREPLACE DIMENSIONS, AND CAUTION VERIFY FRAMING METHODS AND WALL COVERING DETAILS, BEFORE FRAMING CONSTRUCTION BEGINS. PIER-TVFL ST
ملخص المحتوى في الصفحة رقم 16
Negative Pressure warning: When negative pressure Step 3 is present, an atmospherically vented fireplace (with a Negative draft hood) may not function properly and it may down Pressure draft. In the case of a gas appliance, spillage of the combustion gases may occur. This may create a Make-up Air dangerous carbon monoxide situation in the house. The causes of negative pressure to a house can include the following: • Stack effect in the building. • Exhaust only appliances (mechanically and atm
ملخص المحتوى في الصفحة رقم 17
Detailed installation instructions for Model AK-TV Outside Air kit are found in the kit. Air Damper Before lighting the burner, open the damper plate by sliding the air damper rod, located by the gas valve, towards you. DUCT COLLAR DAMPER ASSEMBLY Figure 5. Make-up Air 17
ملخص المحتوى في الصفحة رقم 18
Step 4 A. Vent System Approvals These fireplaces are approved to use 6-inch (152mm) Installing the diameter B-type vent. B-type vent must be used Vent System when the vent system is within combustible construction. These models may also use single wall rigid or flexible gas vent IF and ONLY IF the vent system is installed within non-combustible construction such as a masonry chimney. The same diameters noted above for B-type vent must be used for single-wall vent. See Figure 6. The flame and
ملخص المحتوى في الصفحة رقم 19
4 FT. MINIMUM MAXIMUM HORIZONTAL RUN 17 FT. MAXIMUM 10 FT. MINIMUM 4 FT MINIMUM Figure 6. Vent System Attachment WARNING: THIS GAS FIREPLACE ! MUST NEVER BE VENTED BY CONNECTING TO A CHIMNEY FLUE SERVING A SEPARATE SOLID FUEL BURNING APPLIANCE. 19
ملخص المحتوى في الصفحة رقم 20
C. Bedroom Installation in Canada This model MUST NOT be vented into a vent system installed exterior to a building. The part of the vent system above the roof line can be exterior to the building. D. Vent Termination WARNING: MAJOR U.S. BUILDING ! CODES SPECIFY MINIMUM CHIMNEY AND/OR VENT HEIGHT ABOVE THE ROOF TOP. THESE MINIMUM HEIGHTS ARE NECESSARY IN THE INTEREST OF SAFETY. FIGURE 7 AND TABLE SHOW MINIMUM HEIGHTS, PROVIDED THE TERMINATION CAP IS AT LEAST 8-FEET FROM A VERTICAL WALL. NOTE
