ملخص المحتوى في الصفحة رقم 1
INSTALLATION AND OPERATION
INSTRUCTIONS
MODEL: GRL-700-AU
AUSTRALIAN GAS ASSOCIATION APPROVED
Approval Number 5669
THIS MANUAL MUST BE USED FOR INSTALLATION AND RETAINED
BY HOMEOWNER FOR OPERATION AND MAINTENANCE.
HEAT-N-GLO, a brand of Hearth & Home Technologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044, U.S.A. • (952) 985-6000
This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322; 4,852,548;
ملخص المحتوى في الصفحة رقم 2
INSTALLATION AND OPERATION INSTRUCTIONS PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING THIS APPLIANCE. MODEL GRL-700-AU IS AUSTRALIAN them will void your warranty and may present GAS ASSOCIATION APPROVED FOR a fire hazard. NATURAL GAS OR PROPANE AS A The Heat-N-Glo, a brand of Hearth & Home DECORATIVE GAS LOG. Technologies Inc. warranty will be voided by, and Heat-N-Glo, a brand of Hearth & Home Refer to the appliance data plates for gas Technologies Inc. disclaims any responsibil- consumpt
ملخص المحتوى في الصفحة رقم 3
Table of Contents 1.0 INTRODUCTION .........................................................................................................5 2.0 ASSEMBLY.................................................................................................................5 GAS LINE CONNECTION .........................................................................................6 u LOG PLACEMENT ................................................................................................... 7 3.
ملخص المحتوى في الصفحة رقم 4
FRONT SUROUND PILOT REAR ASSEMBLY SURROUND BURNER PIEZO IGNITOR GRATE CONTROL ACCESS COVER FLEX TUBE GAS VALVE ON/OFF SWITCH TOP VIEW - FIREPLACE AREA DEPTH TOP VIEW NOTE: Unit must WIDTH be 33mm back from fireplace front. 33mm MINIMUM FIREPLACE OPENING Minimum Maximum WIDTH: 700mm 1050mm DEPTH: 300mm 460mm HEIGHT: 425mm 540mm 300mm DEPTH u FIGURE 1 4
ملخص المحتوى في الصفحة رقم 5
CAUTION: DO NOT PLACE ARTICLES ON OR 1.0 INTRODUCTION AGAINST THIS APPLIANCE. Model GRL-700-AU Gas Log Sets are Decorative Gas CAUTION: DO NOT USE OR STORE FLAMMABLE Appliances for Installation in a Solid-Fuel Burning Fire- MATERIALS NEAR THIS APPLIANCE. place. Minimum fireplace size for GRL-700-AU: height 425mm, width 700mm, depth 300mm. CAUTION: DO NOT SPRAY AEROSOLS IN THE VI- CINITY OF THIS APPLIANCE WHILE IT IS IN OP- This log set is to be installed only in a solid-fuel burn- ERATION. ing f
ملخص المحتوى في الصفحة رقم 6
E. NOTE: An Optional Remote Control Kit and Wall A. Inlet gas supply pressure for purposes of input ad- Switch Kit , for turning the burner ON/OFF are avail- justment, shall be 6.0 inches w.c. (1.5kPa) for natu- able. Detailed installation instructions are found in ral gas and 11 inches w.c. (2.75kPa) for propane. each kit. Manifold (outlet) pressure should be 3.2 inches w.c. (.80kPa) for natural gas and 9.6 inches w.c. (2.40kPa) F. Test fire the unit after referring to the SAFETY IN- for propa
ملخص المحتوى في الصفحة رقم 7
LOG PLACEMENT Log Set Assembly: GRL-700-AU-LOGS u INSTRUCTIONS Model: GRL-700-AU STEP 1: Attach grate to as- sembly by sliding hooks into open- FRONT ings on the front surround. SUROUND PILOT REAR ASSEMBLY SURROUND BURNER STEP 2: Ensure that tabs on PIEZO IGNITOR front and rear surrounds are bent as shown in Figure 1. Carefully GRATE remove logs from carton and place as shown. CONTROL ACCESS COVER FLEX TUBE GAS VALVE ON/OFF SWITCH Figure 1 6 1 2 5 3 4 CAUTION: Logs are fragile. Carefully rem
ملخص المحتوى في الصفحة رقم 8
Heat-n-Glo GRL-700/GRL-850 Glowing Embers (Mineral Wool) Placement Natural Gas • Place single layer of 10mm circular sized pieces next to burner ports, taking care not to place material on or between ports. • Do not use all of the ‘ember’ in the packet. One packet should last 5-6 applications. • Repeat application at the start of each season or at the next fireplace service (annually). Note: The contents of the bag is intended for multiple applications. D
ملخص المحتوى في الصفحة رقم 9
Heat-n-Glo GRL-700/GRL-850 Glowing Embers (Mineral Wool) Placement LPG • Place single layer of 10mm circular sized pieces on top of burner ports. • Increase the quantity of the “glowing embers” on the right, centre and left hand side, as indicated, of the burner where there is a cluster of burner ports. • Do not use all of the ‘ember’ in the packet. One packet should last 4-5 applications. • Repeat application at the start of each season or at the next fireplace service (a
ملخص المحتوى في الصفحة رقم 10
1 1 STEP 3: LOG #1 (SRV506-701) Put log #1 behind the locating tab on the right rear corner and up against the locating tab in the center. 2 2 STEP 4: LOG #2 (SRV2010-703) Place log #2 on the right front corner of the unit using its locating slots (on log bottom). 3 3 STEP 5: LOG #3 (SRV506-717) Place log #3 against the left front corner of log #2 as shown. 8
ملخص المحتوى في الصفحة رقم 11
4 4 330mm STEP 6: LOG #4 (SRV591-703) Rest log #4 in between the locating tabs on the rear shelf and rest its front top 330mm from the left corner of the decorative front. 5 5 STEP 7: LOG #5 (SRV550-714) Rest log #5 against log #3 and rest its right edge on log #1. 6 6 STEP 8: LOG #6 (SRV530-716) Place log #6 in the groove on top of log #2 with its front on log #1. 9
ملخص المحتوى في الصفحة رقم 12
3.0 OPERATING GUIDELINES AND MAINTENANCE INSTRUCTIONS Upon completing the gas line connection, a small amount of air will be in the lines. When first lighting the pilot light, it will take a few minutes for the lines to purge themselves of this air. Once the purging is com- plete, the pilot and burner will light and operate as indi- cated in the instruction manual. Subsequent lighting of the appliance will not require such purging. PILOT THERMOCOUPLE FLAME WARNING: BE SURE FIREPLACE SCREEN ! OR
ملخص المحتوى في الصفحة رقم 13
SAFETY INFORMATION FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS ! EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROP- ERTY DAMAGE, PERSONAL INJURY, OR LOSS OF LIFE. A. This appliance has a pilot which must be lighted C. Use only your hand to push in or turn the gas by hand. When lighting the pilot, follow these in- control knob. Never use tools. If the knob will structions exactly. not push in or turn by hand, don’t try to repair it, call a qualified s
ملخص المحتوى في الصفحة رقم 14
LIGHTING INSTRUCTIONS LIGHTING INSTRUCTIONS 1. "STOP!" Read the safety information on previous PILOT ASSEMBLY page. 2. Remove the control access cover. 3. Turn the valve control knob to the "OFF" position. To do this, you must turn the knob clockwise to the "Pilot" position, and then press in and continue turning 6. To put the control in the "Pilot" position, turn the clockwise to the "OFF" position. control knob counter-clockwise to the "Pilot" position. 7. To light t
ملخص المحتوى في الصفحة رقم 15
Service Parts GRL-700-AU (NG, LP) Exploded Parts Diagram Beginning Manufacturing Date: 4-2003 Ending Manufacturing Date: ________ u 2 3 11 8 5 4 7 1 9 8 6 10 12 Log set assembly 13 17 18 16 14 15 Part number list on following page. 13
ملخص المحتوى في الصفحة رقم 16
4.0 REPLACEMENT PARTS: GRL-700-AU When requesting service or replacement parts for your decorative gas log set, please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer. ITEM Description SERIAL # PART NUMBER 1 ON/OFF Rocker Switch 060-521A 2 Burner NG 2010-003 2 Burner LP 2010-005 3 Burner Orifice NG 526-801 3 Burner Orifice LP 526-800 4 Piezo Ignitor 418-513 5 Valve NG 060-524 5 Valve LP 060-526 u 6 Access Door 2010-216 7 Flex Ga
ملخص المحتوى في الصفحة رقم 17
LIMITED 10 YEAR WARRANTY HEAT-N-GLO, a brand of Hearth & Home Technologies Inc. In order to presumptively establish the dates to which your HEAT-N-GLO Limited Warranty runs, you must mail the completed warranty card to HEAT-N-GLO, a brand of Hearth & Home Technologies Inc., 20802 Kensington Boulevard, Lakeville, MN 55044, within 60 days of the date of the fireplace installation. If you fail to do so, you may be required to prove the date of installation before warranty work can be performed. The
