ملخص المحتوى في الصفحة رقم 1
SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY
THIS MANUAL IS PRINTED ON RECYCLED PAPER
By SHERWOOD INDUSTRIES
EG-40 Fireplace Insert Vented Room
Heater
OWNERS MANUAL
Installation And Operating Instructions For Model:- EG-40 FPI. BV.
WHAT TO DO IF YOU SMELL GAS
WARNING
• Open windows/Extinguish any open flame
If the information in this manual
• Do not try to light any appliance.
is not followed exactly, a fire or
explosion may result causing
• Do not t
ملخص المحتوى في الصفحة رقم 2
SAFETY PRECAUTIONS FOR SAFE INSTALLATION AND OPERATION OF YOUR "ENVIROGAS" ROOM HEATER, PLEASE, CAREFULLY READ THE FOLLOWING INFORMATION: installation code in Canada or the National Fuel Gas Code • All "ENVIROGAS" gas-fired appliances must be installed in accordance with these instructions. Carefully ANSI Z223.1.2 in the USA. read all the instructions in this manual first. Consult the building authority having jurisdiction to determine the need • To prevent injury, do not allow any
ملخص المحتوى في الصفحة رقم 3
TABLE OF CONTENTS 1 Code Approvals .....................................................................................................3 2 Specifications.........................................................................................................3 3 Assembly and Installation Instruction ...................................................................4 4 Deciding Where to Locate Your Stove………………………………………………..5 5 Venting...................................................
ملخص المحتوى في الصفحة رقم 4
3. ASSEMBLY AND INSTALLATION INSTRUCTIONS PREPARATION FOR INSTALLATION • Remove the packaging from the appliance, surround panels and log set, check to make sure there is no damage. Carefully check the glass door. Do not use the unit if it is damaged. In the event damage is found please report it to both the courier and your dealer as soon as possible. • Carefully clean the fireplace and flue before installing the stove. Failure to do so may result in fumes or dirt being blown into the
ملخص المحتوى في الصفحة رقم 5
4.DECIDING WHERE TO LOCATE YOUR STOVE DIMENSIONS: A. Mantle pillar to stove 10"/ 25 cm UNIT DIMENSIONS: B. Stove to 8" wide mantle 12"/ 31 cm Front Width: 26"/66 cm Stove must sit on a non-combustible Height Front: 22"/56 cm surface, the width and depth of the insert Height Back: 19-3/4"/50 cm Maintain sufficient clearances Total Depth: 22-1/2"/57 cm for operation, service and maintenance Shipping Weight: 256 lb./116 kg OTHER
ملخص المحتوى في الصفحة رقم 6
VENT TERMINAL CLEARANCES A= Clearance above grade, verandah, porch, deck, or H= *Not to be installed above a meter/regulator [balcony (*12 inches (30 cm) minimum] assembly within 3 feet (90 cm) horizontally B= Clearance to window or door that may be opened from the center-line of the regulator [*12 inches (30 cm) minimum] I= Clearance to service regulator vent outlet C= Clearance to permanently closed window [*6 feet (1.8m) minimum] [minimum 12 inch
ملخص المحتوى في الصفحة رقم 7
5. VENTING WARNING; THIS APPLIANCE HAS BEEN DESIGNED TO OPERATE BY DRAWING COMBUSTION AIR AND DILUTION AIR FROM THE ROOM. IT IS ALSO DESIGNED TO DRAW ROOM AIR FOR PROPER HEAT CIRCULATION FROM THE SIDES OF THE UNIT. BLOCKING OR MODIFYING THE LOUVERS IN ANY WAY CAN CREATE HAZARDOUS SITUATIONS, EITHER THROUGH POOR VENTING OR BY OVERHEATING. IT IS IMPORTANT THAT THIS UNIT HAS SUFFICIENT AIR CIRCULATION FOR PROPER VENTING AND COMBUSTION. PROVISIONS MUST BE MADE FOR THE SUPPLY OF ADEQUATE CO
ملخص المحتوى في الصفحة رقم 8
6. INSTALLATION OF LOG SET and EMBERS INSTALLING THE GLOWING EMBERS A bag of ceramic fiber embers is provided for use on the front burner ember tray. CAUTION: Use only the type of ember material supplied with this appliance. Due to the irregular size of the ember material there may be more than required. Use only a single layer. Do not pile embers. The use of other foreign materials on the burners may create dangerous conditions. If over time, through cleaning and servicing, these
ملخص المحتوى في الصفحة رقم 9
7.OPERATING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE OPERATING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. A) This appliance is equipped with a pilot, which must • If you cannot reach your gas supplier, call the be lit by hand by following these instructions exactly. fire department. B) BEFORE LIGHTING smell all around the appliance C) Use only your hand to push in or turn the gas
ملخص المحتوى في الصفحة رقم 10
8. ROUTINE MAINTENANCE Periodically check to ensure that the "B-Vent" venting open door fully system is clear and that a negative draft is present when • Lift door vertically so that the hinge pins lift out of the unit is operating. hinge receivers. • Return assembly to dealer. Periodically check the pilot and burner flames Your ENVIROGAS Dealer must replace door and glass assembly as a complete unit. No substitute materials are CLEANING OF GLASS allowed. Do not clean glass
ملخص المحتوى في الصفحة رقم 11
9. TROUBLE SHOOTING Problem Cause Solution Spark will not light the pilot after Defective ignitor Check connections to ignitor repeated pressing of spark ignitor -If ignitor connections are good but there is no spark- replace ignitor Miss aligned spark electrode -Check for spark arcing from the electrode to pilot if not adjust by loosening screws on pilot base. Adjust and re- tighten Pilot will not remain lit Defective thermocouple -check for proper connection of thermocouple
ملخص المحتوى في الصفحة رقم 12
10. GAS LINE CONNECTION ORIFICE SIZES, PRESSURE AND BTU’S NATURAL GAS PROPANE GAS FRONT BURNER #48 (1.93 mm) #55 (1.32 mm) REAR BURNER #41 (2.49 mm) #54 (1.40 mm) Manifold pressure. 3.8” wc (.95 kpa) 11” wc(2.74 kpa) Min. Manifold pressures. 1.1” wc (.27 kpa) 2.7” wc(.67 kpa) Supply Pressure. 7.0” wc (1.74 kpa) 12” wc (2.98 kpa) Min. Supply pressures. 5” WC (1.25 kpa) 11.5” WC (2.86 kpa) Max. BTU/H Input. 38,000 Btu/h (11.1 kW) 38,000 Btu/h (11.1 kW) Min. BTU/H Input. 20,
ملخص المحتوى في الصفحة رقم 13
11. ELECTRICAL REQUIREMENTS The ENVIROGAS EG-40 FPI. BV. will operate without an external electrical power supply. This model has a Millivolt gas control which uses the pilot flame to generate enough electricity to operate the main burners. The appliance when installed, must be electrically connected and grounded in accordance with local codes or in the absence of local codes, with the current CSA C22.1 CANADIAN ELECTRICAL CODE Part 1, SAFETY STANDARDS FOR ELECTRICAL INSTALLATIONS, OR
ملخص المحتوى في الصفحة رقم 14
12. PARTS AND ACCESSORIES Service Parts available from your local Envirogas Dealer Burner Control Assembly Convection Blower Natural Gas Pilot Assembly Light Bulb Holder Propane Pilot Assembly Light Switch (momentary) Door Bolt Fan Controller Relief Door Gasket Log Set (with Embers) Regulating Valve Thermocouple Piezo Igniter Embers Burner Switch Thermopile Door Gasket B-vent Spill switch 300°F(149°C) MR. Convection Fan Sensor 120 F (49C) Orifice Blank Accessories Gold trim
ملخص المحتوى في الصفحة رقم 15
• There is a separate air shutter for each burner. • Remove one screw from the cover plate located below the ash shelf. Loosen the other screw (do not remove) swing the cover plate out of the way and tighten screw down to hold it in place. • With along screwdriver rotate spring clips to open or close the shutter to the desired setting. • The burner flame should be a bright yellow/orange when hot. Excessive blue is to lean and dark orange with soot is to rich FUEL TYPE CONVERSION Th
ملخص المحتوى في الصفحة رقم 16
13. WARRANTY Sherwood Industries Ltd. offers a *Lifetime Warranty on this gas product. The lifetime warranty covers the appliance for a period of seven years from the date of installation. This warranty applies only to the original owner in the original location Covered under the lifetime warranty are Cabinet Sides, Tops, Pedestals, Surround Panels and Chassis and Heat Exchanger. These steel components are covered against manufacturer’s defects for 5 years and labor for the first yea
ملخص المحتوى في الصفحة رقم 17
14. INSTALLATION DATA SHEET The installer for warranty purposes and future reference must record the following information. Model: EG 40 FPI Name of Owner: Name of Dealer: __________________________________________ ___________________________________________ Address: Address: __________________________________________ ___________________________________________ ___________________________________________ __________________________________________
