ملخص المحتوى في الصفحة رقم 1
Installation and Operating Instructions
08/18887/1 Issue 1
Wall Fire SP4
Model No: SP420
Dimensions
(millimetres)
Fig. 1
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE.
Electrical
Important Safety Advice:
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the
When using electrical appliances, basic
voltage marked on the heater must correspond to the supply
precautions should be followed to reduce the risk
of fire, ele
ملخص المحتوى في الصفحة رقم 2
Installation Do not connect appliance until properly fixed to the wall a and the Instruction leaflet is read fully. lift appliance above wall ledge fixing bracket This model is designed to be permanently fixed to a wall at a wall ensure ledge bracket at back of minimum height of 300mm. fire engages wall bracket The wall bracket must be fitted horizontally and the cable see detail '1' Detail '1' routed to the bottom right of the heater as in Fig 1. wall bracket slide down over outline of wall b
ملخص المحتوى في الصفحة رقم 3
Manual Operation The Standby Switch (Switch 1) must be first turned ‘ON’ and the AUTO/MAN (Switch 2) switch set to ‘MANUAL’ to operate the manual controls - see Fig 6. Note : When the fire is put in Manual mode the first time the flame effect will come on indicated by the Bottom neon coming on for 3 seconds - see Fig 7. MAN AUTO ON OFF Manual Controls Fig. 6 Setting Indication Operation Flame Effect only Press the ‘ I ’ button (Switch 3) Top Neon Flame Effect & Heat On Press the ‘ I ’ button aga
ملخص المحتوى في الصفحة رقم 4
• Heat settings Remote Control Operation Navigate the cursor to HEAT with the buttons. Press General ----- to change the heat setting between off/low heat. The remote control consists of 5 control buttons and a LCD Note: If the room temperature is higher than the remote display with a visible area of 40x40mm. control set temperature located on the left side of LCD display, heat will not come on (see Thermostat operation below). The maximum range of use for the remote control is 15metres. •
ملخص المحتوى في الصفحة رقم 5
Replacing the remote control The new remote control must be set up as follows: Press switch 1 to ON . Press switch 2 to AUTO (see Fig. 6). Press switch 3 to O for more than 3 seconds until both LED’s are on (see Fig. 7). Press the remote control’s enter button or the buttons. Now the heater has learned the serial number from the remote control and will work with this remote control only (this procedure is repeatable many times). General information 1. In case that the remote control is out
ملخص المحتوى في الصفحة رقم 6
For access to the bottom bulbs, carefully slide the flexible ro- Lamp Replacement tisserie to one side ensuring that the rubber grommets are not lost (see Fig 11). WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE REMOVING LAMPS. The front surround will need to be removed in order to change lamps. Warning -The front surround is heavy and easily damaged !. The front surround is fixed with 4 spring loaded pins and is supported at the top by the chassis. To gain access to the lamps please ap
ملخص المحتوى في الصفحة رقم 7
Cleaning WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER. For general cleaning use a soft clean duster – never use abrasive cleaners. The glass viewing screen should be cleaned carefully with a soft cloth. DO NOT use proprietary glass cleaners. After Sales Service Your product is guaranteed for one year from the date of pur- chase. Within this period, we undertake to repair or exchange this product free of charge (excluding lamps & subject to avail- ability) provided
ملخص المحتوى في الصفحة رقم 8
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 89/336 Glen Dimplex UK Limited UK customer help line (8.00AM – 6.00PM Mon-Fri; 8.30AM-1.00PM Sat) Millbrook House Customer Services: Tel. 0870 7270101 Grange Drive Fax. 0870 7270102 Hedge End e-mail customer.services@glendimplex.com Southampton Hampshire. SO30 2DF
