ملخص المحتوى في الصفحة رقم 1
®
GE Monogram
Installation
Instructions
30″ Electric
Radiant Cooktop
Model
ZEU30R
Monogram.com
ملخص المحتوى في الصفحة رقم 2
Before you begin—Read these instructions completely and carefully. IMPORTANT—Save these instructions for local inspector’s use. IMPORTANT—OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer—Be sure to leave these instructions with the Consumer. Note to Consumer—Keep these instructions for future reference. Note—This appliance must be properly grounded. ATTENTION INSTALLER: ALL COOKTOPS MUST BE HARD WIRED (DIRECT WIRED) INTO AN APPROVED JUNCTION BOX. A “PLUG AND RECEPTACLE” IS NOT PERMI
ملخص المحتوى في الصفحة رقم 3
ON HOT Design Information Electronic Radiant Cooktop Design Information Contents Models Available .....................................................................................................................................................................3 Advance Planning ...................................................................................................................................................................3 Tools & Materials Required ..........................
ملخص المحتوى في الصفحة رقم 4
Preparing the Opening Electronic Radiant Cooktop Tools & Materials Needed Tools You Will Need Materials Required Phillips Head Junction Box 1/8″ Drill Bit & Wire Nuts Pencil Screwdriver Electric or Hand Drill Ruler or Saber Saw Straightedge 13" MAX. Depth of unprotected overhead cabinets The following MINIMUM clearance Minimum 1 1/2" MIN. clearance from dimensions must be maintained. Clearances cutout to side wall on the right of the unit 30" MIN. clearance from 18" MIN. countertop to height
ملخص المحتوى في الصفحة رقم 5
Installation Electronic Radiant Cooktop Vertical Five inches (5″) minimum vertical clearance between the cooktop bottom and any combustible surfaces. Clearance 5"Min. Vertical Clearance 19 5/8" width of cut To insure accuracy, it is best to make a Cutout 28 1/2" template when cutting the opening in the length 1 3/4" Min. Dimensions of cut Between cutout counter. Make sure there is clearance rear edge and the of the inside the cabinet before cutting the wall behind the cooktop countertop. Cou
ملخص المحتوى في الصفحة رقم 6
Installation Electronic Radiant Cooktop Bottom of Attach Apply the foam strips around the outer edge Cooktop of the glass. Do not overlap the foam strips. Foam Strips Foam Strips Cooktop Glass MOUNTING Remove the hold down brackets and Locate SCREW screws from the literature package. Mounting Parts Attach Screw the Hold Down Bracket to the side of the cooktop unit. Repeat for opposite side Brackets to of cooktop. Cooktop Pre-drilled hole Bottom of Cooktop Foam Strips Cooktop Glass Insert Inse
ملخص المحتوى في الصفحة رقم 7
Electrical Connections Electronic Radiant Cooktop When making the wire connections, use the entire length of conduit provided. The conduit must not be shortened. Step 1 With the cooktop in place, open the front of the cabinet door. Step 2 Insert the wires from the conduit through the opening Strain of the junction box. Step 3 Relief Red Clamp Ground Black Connect the red and black leads from the Red cooktop conduit to the corresponding leads Step 4 in the junction box. Ground Black wire loc
ملخص المحتوى في الصفحة رقم 8
Checking the Installation & Cooktop Operation Electronic Radiant Cooktop • Remove all protective film if present, and any stickers. Pre-Test Checklist • Check to be sure that all wiring is secure and not pinched or in contact with moving parts. • Check level of appliance. • Check that the cooktop is properly grounded. Operation • Remove all items from the top of the cooktop surface. Checklist • Turn on the power to the cooktop. (Refer to your Owner’s Manual.) Verify that all surface units operat
