ملخص المحتوى في الصفحة رقم 1
READ AND SAVE THESE INSTRUCTIONS
®
™
COOLER
Model No.
Ceiling Fan
CF925BK00
Owner's Manual
CF925BS00
CF925WW00
Net Weight: 26.8 Lbs.
CF925OB00
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials.
You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will last for th
ملخص المحتوى في الصفحة رقم 2
! WARNING WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’s manual carefully and keep it for future reference. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. 3. Be careful of
ملخص المحتوى في الصفحة رقم 3
This Manual Is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan Installed Wire Length Wire Size A.W.G. Tools Needed for Assembly Up to 50 ft. 14 One Phillips head screwdriver One stepladder 50-100 ft. 12 One 1/4” blade screwdriver One wire stripper Three wire connectors (supplied) One 3/16” hex wrench (supplied) ! WARNING Before assembly your ceiling fan, refer to section on MATERIALS proper method of wiring your fan (page 6). If you fee
ملخص المحتوى في الصفحة رقم 4
How to Put Your Ceiling Fan Together 1. Remove the hanger ball by loosening the setscrew 4. Make sure the grommet is properly installed in the in the hanger ball until the ball falls freely down the coupling cover then slide the coupler cover on the downrod (Figure 1). Remove the clevis pin from the downrod until it rests on the motor housing. Place downrod, then remove the hanger ball. Retain the the ceiling cover over the downrod. Be sure both pin and hanger ball for reinstallation in step 5.
ملخص المحتوى في الصفحة رقم 5
FIBER 11.Connect the white wire from the light kit plate to BLADE the white wire from the motor; connect the black 3/16-24 x 5/16" SLOTTED WASHER PHILLIP WASHER HEAD wire from the light kit plate to the blue wire from BLADE SCREW (3) the motor (Figure 7). Make sure the connectors are fully engaged. 12.Position the light kit plate so that the studs on the FAN BLADE adapter plate protrude through the three holes in the light kit plate. Install a 3/16-24 nut on each BLADE FLANGE stud. Figure 5 NOTE
ملخص المحتوى في الصفحة رقم 6
NOTE: CEILING COVER, How to Hang Your SUPPLY WIRES AND OUTLET FAN WIRES OMITTED BOX Ceiling Fan FOR CLARITY. ! WARNING The fan must be hung with at least 7' of clearance from floor to blades (Figure 9). HANGER BRACKET CEILING Figure 11 HANGER BALL/ DOWNROD ASSEMBLY AT LEAST How to Wire Your Ceiling Fan 7' If you feel that you do not have enough electrical Figure 9 FLOOR wiring knowledge or experience, have your fan installed by a licensed electrician. ! WARNING 1. Your ceiling fan is supplied wi
ملخص المحتوى في الصفحة رقم 7
Installing Glass Globe 1. Install three candelabra base bulbs in sockets. 2. Place the glass bowl into the opening in the light kit plate, aligning the three flat areas on the top edge of the glass with the three raised dimples on the LIGHT KIT PLATE light kit plate and turn the glass bowl clockwise until RAISED DIMPLES it stops (Figure 13). NOTE: periodically check that the glass bowl is seated fully clockwise in the light kit plate. FLAT AREA Figure 13 Using Your Ceiling Fan 1. Restore electri
ملخص المحتوى في الصفحة رقم 8
Maintenance IMPORTANT CARE INSTRUCTIONS Abrasive cleaning agents are not required and should for your Ceiling Fan be avoided to prevent damage to finish. Periodic cleaning of your new ceiling fan is the only WARNING maintenance that is needed. ! When cleaning, use only a soft brush or lint free cloth Do not use water when cleaning your ceiling fan. It to avoid scratching the finish. could damage the motor or the blades and create the possibility of an electrical shock. Accessories 1. Downrod Ext
