ملخص المحتوى في الصفحة رقم 1
1F80-361 1F80-361 1F80-361 1F80-361 1F80-361
Programmable Electronic Digital Thermostat
INSTALLATION AND INSTALLATION AND INSTALLATION AND INSTALLATION AND INSTALLATION AND
OPERATION INSTRUCTIONS OPERATION INSTRUCTIONS OPERATION INSTRUCTIONS OPERATION INSTRUCTIONS OPERATION INSTRUCTIONS
Operator: Save these instructions for future use! Operator: Save these instructions for future use! Operator: Save these instructions for future use! Operator: Save these instructions for future use! Operator
ملخص المحتوى في الصفحة رقم 2
INSTALLATION INSTALLATION INSTALLATION INSTALLATION INSTALLATION REMOVE OLD THERMOSTAT REMOVE OLD THERMOSTAT REMOVE OLD THERMOSTAT REMOVE OLD THERMOSTAT REMOVE OLD THERMOSTAT Screw anchors 1. Shut off electricity at the main fuse box until installation is complete. Ensure that electrical power is disconnected. 2. Remove the front cover of the old thermostat. With wires With wires With wires With wires With wires still attached, still attached, still attached, still attached, still attached, rem
ملخص المحتوى في الصفحة رقم 3
JUMPER THERMOSTAT WIRE ‡ C B O Y G W RC RH THERMOSTAT SYSTEM ‡ C Y B O G W RC RH Hot SYSTEM Cooling Fan Heating 24 VAC 120 VAC System Relay System Fan Heating Neutral Relay System Hot HEATING TRANSFORMER 24 VAC 120 VAC NOTE Neutral For 2-wire Heat only, Hot attach to RH and W TRANSFORMER 24 VAC 120 VAC Figure 2. Typical wiring diagram for Neutral heat only, 3-wire, single transformer systems COOLING TRANSFORMER Figure 5. Typical wiring diagram for heat/cool, 5-wire, two-transformer systems JUM
ملخص المحتوى في الصفحة رقم 4
OPERATION OPERATION OPERATION OPERATION OPERATION Before you begin programming your thermostat, you should be familiar with its features and with the display and the location and operation of the thermostat buttons. Your thermostat con- sists of two parts: the thermostat cover thermostat cover thermostat cover and the base base base. To thermostat cover thermostat cover base base remove the cover, pull it straight out from the base. To replace the cover, line up the cover with the base and press
ملخص المحتوى في الصفحة رقم 5
Configuration Menu Step Press Button(s) Displayed (Factory Default) Press or to select: COMMENTS 1 HOLD 0 to 8 hrs (in Select temporary Hold time PRGM (0:00) 15 minute increments) and RUN SL Select FA or SL (Fast or Slow) heating cycle rate 2 HOLD* (FA) d-L 3 HOLD* OFF Select display backlight OFF or ON (ON) E 4 HOLD* OFF Select Energy Management Recovery OFF or ON (ON) 5 Filter 0 to 1950 hours HOLD* Select filter replacement run time (000) (in 50 hour increments) 6 L
ملخص المحتوى في الصفحة رقم 6
Enter Heating Program Enter Heating Program Planning Your Program Planning Your Program Planning Your Program Planning Your Program Planning Your Program Enter Heating Program Enter Heating Program Enter Heating Program 1. Move the SYSTEM switch to HEAT HEAT HEAT HEAT HEAT. Look at the factory preprogrammed times and temperatures shown in the sample schedule. If this program will suit your 2. Press PRGM once. “MO TU WE TH FR MO TU WE TH FR M MO TU WE TH FR MO TU WE TH FR O TU WE TH FR” (indicati
ملخص المحتوى في الصفحة رقم 7
Enter Cooling Program Enter Cooling Program Enter Cooling Program Enter Cooling Program Enter Cooling Program CHECK YOUR PROGRAMMING CHECK YOUR PROGRAMMING CHECK YOUR PROGRAMMING CHECK YOUR PROGRAMMING CHECK YOUR PROGRAMMING Follow these steps to check your thermostat programming one ! CAUTION CAUTION CAUTION CAUTION CAUTION final time before beginning thermostat operation. If the outside temperature is below 50°F, disconnect If the outside temperature is below 50°F, disconnect If the outside
ملخص المحتوى في الصفحة رقم 8
TROUBLESHOOTING TROUBLESHOOTING TROUBLESHOOTING TROUBLESHOOTING TROUBLESHOOTING Symptom Symptom Symptom Symptom Symptom Possible Cause Possible Cause Possible Cause Possible Cause Possible Cause Corrective Action Corrective Action Corrective Action Corrective Action Corrective Action Heat, Cool or Fan Runs Constantly. Heat, Cool or Fan Runs Constantly. Heat, Cool or Fan Runs Constantly. Heat, Cool or Fan Runs Constantly. Heat, Cool or Fan Runs Constantly. 1. FAN Switch set to Fan ON. Check each
