ملخص المحتوى في الصفحة رقم 1
ADDENDUM TO
MODEL 100E
OPERATORS MANUAL
(P/N 04515)
FOR
MODEL 100EU
TRACE LEVEL SULFUR DIOXIDE
ANALYZER
9480 CARROLL PARK DRIVE
SAN DIEGO, CA 92121-5201
USA
Toll-free Phone: 800-324-5190
Phone: 858-657-9800
Fax: 858-657-9816
Email: Api-sales@teledyne.com
Website: http://www.teledyne-api.com/
05831 Rev C
DCN 5379
© 2007 T-API 08 April 2009
ملخص المحتوى في الصفحة رقم 2
ملخص المحتوى في الصفحة رقم 3
M100EU – OPERATIONS MANUAL TELEDYNE INSTRUMENTS Addendum to M100E Manual - P/N 04515 TABLE OF CONTENTS TABLE OF CONTENTS 1. PREFACE ..........................................................................................................................................................................3 1.1 Reference Numbering convention.............................................................................................................................3 2. SPECIFICATIONS, APPROVALS
ملخص المحتوى في الصفحة رقم 4
TELEDYNE INSTRUMENTS M100EU – OPERATIONS MANUAL TABLE OF CONTENTS Addendum to M100E Manual - P/N 04515 LIST OF FIGURES Figure 3-1: M100EU Internal Layout ................................................................................................................7 Figure 3-2: M100EU Test Functions ................................................................................................................9 Figure 6-1: Accessing the STBL Menu .........................................
ملخص المحتوى في الصفحة رقم 5
M100EU – OPERATIONS MANUAL TELEDYNE INSTRUMENTS Addendum to M100E Manual - P/N 04515 PREFACE 1. PREFACE NOTE The information contained in this addendum is pertinent to M100EU analyzers running software revision F.0. Some or all of the information may not be applicable to later revisions of software. The software revision your analyzer is running is displayed in the upper left-hand corner of the display any time the instrument is in SETUP mode. This addendum is based on the Model 100
ملخص المحتوى في الصفحة رقم 6
TELEDYNE INSTRUMENTS M100EU – OPERATIONS MANUAL PREFACE Addendum to M100E Manual - P/N 04515 USER NOTES: 4 05944 Rev B PRINTED DOCUMENTS ARE UNCONTROLLED DCN 5063
ملخص المحتوى في الصفحة رقم 7
M100EU – OPERATIONS MANUAL TELEDYNE INSTRUMENTS Addendum to M100E Manual - P/N 04515 SPECIFICATIONS, APPROVALS AND WARRANTY 2. SPECIFICATIONS, APPROVALS AND WARRANTY 2.1 SPECIFICATIONS Table 2-1: Model 100EU Basic Unit Specifications Min/Max Range In 1ppb increments from 50ppb to 20 000ppb, dual ranges or auto ranging (Physical Analog Output) Measurement Units ppb, ppm, µg/m3, mg/m3 (user selectable) 2 Zero Noise 25 ppt RMS (50 ppt RMS with 360 nM filter installed) 2 Span Noise 0.5%
ملخص المحتوى في الصفحة رقم 8
TELEDYNE INSTRUMENTS M100EU – OPERATIONS MANUAL SPECIFICATIONS, APPROVALS AND WARRANTY Addendum to M100E Manual - P/N 04515 2.2 EPA EQUIVALENCY DESIGNATION At this time the M100EU has not been certified by the EPA as an equivalent method at the time of this writing however it is anticipated that the M100EU will qualify as Reference Method Number EQSA-0495-100 per 40 CFR Part 53 in the near future. Please see section 2.2 of the M100E manual, P/N 04515 for details. 2.3 CE MARK COMPLIANCE
ملخص المحتوى في الصفحة رقم 9
M100EU – OPERATIONS MANUAL TELEDYNE INSTRUMENTS Addendum to M100E Manual - P/N 04515 GETTING STARTED 3. GETTING STARTED 3.1 UNPACKING THE M100EU Unpack the M100EU as per the directions in Section 3.1 of the M100E Manual - P/N 04515, with the following change. There are two redheaded shipping screws that hold down the PMT/Sensor assembly and must be removed prior to operation. They are located along the base of the PMT housing adjacent to the chassis. 3.2 INTERNAL LAYOUTS Figures 3-1
ملخص المحتوى في الصفحة رقم 10
TELEDYNE INSTRUMENTS M100EU – OPERATIONS MANUAL GETTING STARTED Addendum to M100E Manual - P/N 04515 3.3 FUNCTIONAL CHECK OF THE M100EU To perform an initial functional check of the M100EU follow the steps contained in Section 3.2.4 of the M100E Manual - P/N 04145, but use the Test functions described in below. 3.3.1 TEST FUNCTIONS Table 3-1 supersedes the figure in Step 2 of Section 3.2.4 and Figure 6-2 of the M100E Manual - P/N 04145. Table 11-1 supersedes Table 6-2. The only differe
ملخص المحتوى في الصفحة رقم 11
M100EU – OPERATIONS MANUAL TELEDYNE INSTRUMENTS Addendum to M100E Manual - P/N 04515 GETTING STARTED Table 3-1: Test Functions Defined DISPLAY PARAMETER UNITS DESCRIPTION The overall offset of the instrument as calculated during the last OFFSET SO measurement Offset - calibration activity. The offset parameter is used to set the zero 2 point of the analyzer response. HVPS HVPS V The PMT high voltage power supply. SAMPLE CHAMBER RCELL TEMP °C The current temperature of the sample cha
ملخص المحتوى في الصفحة رقم 12
TELEDYNE INSTRUMENTS M100EU – OPERATIONS MANUAL GETTING STARTED Addendum to M100E Manual - P/N 04515 USER NOTES: 10 05944 Rev B PRINTED DOCUMENTS ARE UNCONTROLLED DCN 5063
ملخص المحتوى في الصفحة رقم 13
M100EU – OPERATIONS MANUAL TELEDYNE INSTRUMENTS Addendum to M100E Manual - P/N 04515 FREQENTLY ASKED QUESTIONS & GLOSSARY 4. FREQENTLY ASKED QUESTIONS & GLOSSARY Please refer to Section 4 of the M100E manual, PN 04515 for information. 05944 Rev B 11 DCN 5063 PRINTED DOCUMENTS ARE UNCONTROLLED
ملخص المحتوى في الصفحة رقم 14
TELEDYNE INSTRUMENTS M100EU – OPERATIONS MANUAL FREQUENTLY ASKED QUESTIONS & GLOSSARY Addendum to M100E Manual - P/N 04515 USER NOTES: 12 05944 Rev B PRINTED DOCUMENTS ARE UNCONTROLLED DCN 5063
ملخص المحتوى في الصفحة رقم 15
M100EU – OPERATIONS MANUAL TELEDYNE INSTRUMENTS Addendum to M100E Manual - P/N 04515 OPTIONAL HARDWARE AND SOFTWARE 5. OPTIONAL HARDWARE AND SOFTWARE Please refer to Section 5 of the M100E manual, PN 04515 for information. 05944 Rev B 13 DCN 5063 PRINTED DOCUMENTS ARE UNCONTROLLED
ملخص المحتوى في الصفحة رقم 16
TELEDYNE INSTRUMENTS M100EU – OPERATIONS MANUAL OPTIONAL HARDWARE AND SOFTWARE Addendum to M100E Manual - P/N 04515 USER NOTES: 14 05944 Rev B PRINTED DOCUMENTS ARE UNCONTROLLED DCN 5063
ملخص المحتوى في الصفحة رقم 17
M100EU – OPERATIONS MANUAL TELEDYNE INSTRUMENTS Addendum to M100E Manual - P/N 04515 M100EU OPERATING INSTRUCTIONS 6. M100EU OPERATING INSTRUCTIONS NOTE For the most part the operation instruction for the M100EU are the same as those described in Chapter 6 of the M100E Manual - P/N 04515 with the exception that there are additional test parameters and setup procedures. 6.1 ADDITIONAL TEST PARAMETERS Please see Section 3.3 above for details on the additional test parameters. 6.2 STB
ملخص المحتوى في الصفحة رقم 18
TELEDYNE INSTRUMENTS M100EU – OPERATIONS MANUAL M100EU OPERATING INSTRUCTIONS Addendum to M100E Manual - P/N 04515 SAMPLE RANGE = 500.000 PPB SO2 =XXX.X < TST TST > CAL SETUP SETUP X.X PRIMARY SETUP MENU EXIT returns to the main SAMPLE CFG DAS RNGE PASS CLK MORE EXIT display SETUP X.X SECONDARY SETUP MENU EXIT returns to the PRIMARY SETUP MENU COMM VARS DIAG STBL SETUP X.X CONC1, 10SEC, 25 SAMPLES
ملخص المحتوى في الصفحة رقم 19
M100EU – OPERATIONS MANUAL TELEDYNE INSTRUMENTS Addendum to M100E Manual - P/N 04145 CALIBRATION PROCEDURES 7. CALIBRATION PROCEDURES Calibration of the M100EU should be performed according to the procedures described in Chapters 7 & 8 of the M100E Manual - P/N 04145. However, delivering span and zero gases for the lower ranges that the M100EU is designed for can be difficult. For best results when calibrating the M100EU, wait one hour for the instrument to stabilize when delivering zer
ملخص المحتوى في الصفحة رقم 20
TELEDYNE INSTRUMENTS M100EU – OPERATIONS MANUAL CALIBRATION PROCEDURES Addendum to M100E Manual - P/N 04515 USER NOTES: 18 05944 Rev B PRINTED DOCUMENTS ARE UNCONTROLLED DCN 5063
