ملخص المحتوى في الصفحة رقم 1
®
PAINT/TEXTURE
AIR GUN
Model 02471
ASSEMBLY and OPERATING
INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2002 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
ملخص المحتوى في الصفحة رقم 2
Specifications Capacity 1.45 Gallons Air Inlet 1/4” NPS (Male) Recommended PSI 50 - 70 PSI Cup Dimensions 10” H x 9-7/8” x 9” Nozzle Sizes 4.5 mm (.177”), 6mm (.236”), 8mm (.314”) Top Opening 7-7/8” L x 4-3/16” CFM Required 4-6 CFM Funnel Opening 1-5/8” Save This Manual . You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice num
ملخص المحتوى في الصفحة رقم 3
9. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines. 10. Maintain tools with care. Keep tools clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords and hoses periodically and, if damaged, have them repaired by an authorized technician. The handles must be kept clean, dry, and free from oil and grease at all times. 11. Disconnect power. When not in use disconnect from c
ملخص المحتوى في الصفحة رقم 4
23. Read labels on cleaning solvents and paint coatings. Chlorinated solvents such as 111-Trichloroethane and Methylene Chloride (also known as methyl-chloride) can chemically react with aluminum and may explode. Many paint sprayers contain aluminum. Contact solvent manufacturer or paint supplier if your are in doubt. 24. Paints and solvents may be harmful or fatal if swallowed or inhaled. Always use a respirator that is appropriate for type of paint/solvent being used when spraying. Avoid
ملخص المحتوى في الصفحة رقم 5
Assembly Refer to Assembly Drawing on page 9. 1. To attach the Cup (#17), use the Clamp (#18) to connect it to the Body (#3). Operation Warning! Never allow the Spray Gun and Cup (#17) to lay on it’s side when the Cup (#17) is full of material. 1/4” NPS (Male) Air Spray Air Compressor Gun Dryer For best service, you should incorporate an air dryer, a regulator, and an inline air filter, as shown above. We recommend an air dryer to send moisture-free air to the Spray Gun. All are available at
ملخص المحتوى في الصفحة رقم 6
Adjustments 1. You can regulate the fluid flow with the Regulator Guide (#8). Slowly turn it to fine tune the air pressure to meet your needs. You may also adjust the pressure with the air compressor. Make sure you do not exceed the recommended 70 PSI. 2. You can change Nozzles (#2a, #2b, #2c) for different shaped sprays. First, disconnect from the air source. Next, unscrew the Retaining Ring (#1). Unscrew the nozzle that is on the unit and screw on the one you want to use. Screw on the R
ملخص المحتوى في الصفحة رقم 7
Maintenance Cleaning (Gun should be attached to compressor to complete the cleaning process.) Warning!! Do not use paint strippers on this unit as they will damage the aluminum. Never allow the unit to lay on it’s side while paint is in the Cup (#17). 1. Empty paint from Cup (#17) and add small amount of clean solvent. Replace Cup (#17) and shake vigorously. At the lowest possible pressure, spray out the solvent into a waste bucket (make sure you are wearing respirator and eye protection).
ملخص المحتوى في الصفحة رقم 8
Parts List Part No. Description Qty. 1 Retaining Ring 1 2a Nozzle (.177”) 1 2b Nozzle (.236”) 1 2c Nozzle (.314”) 1 3 Body 1 4 0-ring 1 5 Fitting 1 6 0-ring 1 7 0-ring 1 8 Regulator Guide 1 8a O-ring 1 9 Needle Shaft 1 10 0-ring 2 11 Assembly Set 1 11a O-ring 1 12 Clip Ring 1 13 Air Inlet 1 14 Trigger 1 15 Pin 1 16 E-ring 1 17 Cup 1 18 Clamp 1 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER T
ملخص المحتوى في الصفحة رقم 9
Assembly Drawing SKU 02471 Page 9 REV 06/05 11a 8a 8
