ملخص المحتوى في الصفحة رقم 1
HVLP ELECTRIC PAINT SPRAYER
91772
ASSEMBLY AND OPERATING INSTRUCTIONS
®
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
®
. All rights reserved. No portion of this
Copyright 2004 by Harbor Freight Tools
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical q
ملخص المحتوى في الصفحة رقم 2
PRODUCT SPECIFICATIONS Motor 115 V, 60 Hz, 450 Watt, Single Phase Maximum Pressure 2-5 PSI Air Intake 1500 Liters Per Minute Hose Twist Lock O-ring Connection, 7 Ft. Long Includes: Viscosity Cup, Small Inflator, Shoulder Carry Strap, 1 Liter Paint Cup. SAVE THIS MANUAL You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and as- sembly diagram. Keep your invoice with this manual. Write the invoice n
ملخص المحتوى في الصفحة رقم 3
ELECTRICAL SAFETY 4. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user. 5. Double insu
ملخص المحتوى في الصفحة رقم 4
12. Avoid accidental starting. Be sure the Power Switch is off before plugging in. Carrying power tools with your finger on the Power Switch, or plugging in power tools with the Power Switch on, invites accidents. 13. Remove adjusting keys or wrenches before turning the power tool on. A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury. 14. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable
ملخص المحتوى في الصفحة رقم 5
23. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. SERVICE 24. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 25. When servicing a tool, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this ma
ملخص المحتوى في الصفحة رقم 6
11. WARNING: The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety code § 25249.5, et seq.) 12. WARNING! People with pacemakers should consult their physician(s) before using this product. Electromagnetic fields in close proximity to a heart pacemaker could cause interference to or failure of the pacemaker. REV 11/06 SKU 91772 For technical questions, please call 1-800-444
ملخص المحتوى في الصفحة رقم 7
GROUNDING WARNING! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet insta
ملخص المحتوى في الصفحة رقم 8
DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS 4. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure B.) 5. Double insulated tools may be used in either of the 120 volt outlets shown in the following illustration. (See Figure B.) FIGURE B EXTENSIO
ملخص المحتوى في الصفحة رقم 9
6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. 7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 8. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120 VOLT) NA
ملخص المحتوى في الصفحة رقم 10
UNPACKING When unpacking, check to make sure all the parts shown on the Parts List on page 14 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. ASSEMBLY AND OPERATING INSTRUCTIONS NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 15. CAUTION: Always make sure the Power Cord of the Sprayer is unplugged from its electrical ou
ملخص المحتوى في الصفحة رقم 11
ASSEMBLY AND OPERATING INSTRUCTIONS (continued) Refer to the Assembly Drawing on page 15 and FIGURE 1 on page 10. Checking the Paint Viscosity When using a HVLP (low pressure and high volume) spray gun the paint must be thinned to the proper viscosity. Viscosity indicates whether the material is very liquid (low viscosity) versus very thick (high viscosity). Viscosity is measured in the seconds it takes for the paint to flow through the viscosity meter (DINs). Ask your paint sales repre- sent
ملخص المحتوى في الصفحة رقم 12
ASSEMBLY AND OPERATING INSTRUCTIONS (continued) 5. Secure the Spray Gun in the Gun Tray (41). If the Gun Tray (41) is not attached to the Motor Unit, attach it as shown in FIGURE 3 on page 11. 6. To adjust the type of spray required, loosen the Lock Ring (17) and rotate the Fluid Tip (16) for a horizontal, vertical, or round spray. Practice spraying on scrap mate- rial to get the feel of the adjustments. When finished, tighten the Lock Ring (17). Note: Horizontal and vertical sprays are reco
ملخص المحتوى في الصفحة رقم 13
Note: A small Inflator (32) accessory comes with this unit. To fill a raft or air mattress, attach the inflator as shown in FIGURE 2 on page 11. When the inflator is attached to the object being inflated, start the unit using the Switch (31). Turn off the unit when the object is inflated. Read the instruction manual of the object to be inflated to determine the recommended and maximum PSI for filling the object. You will have to check the air pressure of the object by using a separate air p
ملخص المحتوى في الصفحة رقم 14
PARTS LIST Part Description Qty. Part Description Qty. 1 Fluid Needle Screw 1 24 Paint Cup 1 2 Needle Spring 1 25 Trigger 1 3 Washer 1 26 Handle O-ring 2 4 Fluid Needle 1 27 Gun Body 1 5 Needle Cover 1 28 Strap 1 6 Needle Sealing Thread 1 29 Exhaust Cover 1 7 Gasket 2 30 Filter 1 8 Bolt 1 31 Switch 2 9 Plug 1 32 Inflator 1 10 Washer 1 33 Viscosity Cup 1 11 Pin 1 34 Cord 1 12 Washer 1 35 Pin Board 1 13 Sealing Thread Head 1 36 Front Turbine Shell Pin 1 14 Sealing Ring Head 1 37 Back Turbine Shell
ملخص المحتوى في الصفحة رقم 15
ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 91772 For technical questions, please call 1-800-444-3353. Page 15
