ملخص المحتوى في الصفحة رقم 1
Martindale
USER INSTRUCTIONS: MAGNUM P2/P3 POWERED RESPIRATORS
Models covered
Power Units : M23/1000, M23/2000, M23/8500
Powered Respirator kits: M23/1000/CB, M23/2000/CB, M23/8500/CB
(Power Unit, 8-hour Battery and UK Charger)
Available Headpieces: See section 2 below
Before using the system it is essential that you read these instructions and ensure that the correct equipment has
been selected. Always be aware of the limitations of use of th
ملخص المحتوى في الصفحة رقم 2
Compatibility between Headpieces and Power Units: Headpieces: Power Units: Description Code 1000/2000 8500 Rigid Polycarbonate Visor with Saronex Hood M23RVSN Flip up Polycarbonate Visor M23FUVN Helmet with Flip-up Polycarbonate Visor M23HFUV High Temperature Helmet with Clear Triacetate Flip up Visor M23HFUVHTT High Temperature Helmet with Gold Polycarbonate Visor M23HFUVHTGP Automatic Welding Visor M23A
ملخص المحتوى في الصفحة رقم 3
Allow the charge to continue as the charger will try and trickle charge the battery up to a acceptable pre-set level before commencing the battery charge, when the RED LED will continuously illuminate (this may take several hours) . If the charger refuses to charge the battery it may be faulty – contact Centurion Safety Products for further help and assistance. It is possible that a battery in this state may require several charge attempts to fully charge the battery. *It is not recommended to d
ملخص المحتوى في الصفحة رقم 4
Main filters Part number: M23P2/5 or M23P2OD/5 THP2 /TH2P filters – for use with Magnum 1000 and 2000 Power Unit Part Number: M23P3/5 TH3P filter – For use with Magnum 2000 Power Unit only WARNING Care should be taken when handling filters. Do not touch the pleated paper filter medium. Do not use filters with damaged paper filter medium. Do not use filters after their expiry date. Do not use filters with no or damaged filter seal. Filters should be fitted as follows. : Remove the front cover by
ملخص المحتوى في الصفحة رقم 5
Replace the retaining ring and screw it up securely. Do not over tighten the ring. The labelled portion of the filter and the louver protrude through the ring. Ensure that the rubber seals in the filter ports of the power unit are present, in good condition and seated flat at the bottom of the threaded section. Screw the holder(s) & filter(s) into the Din 40 ports of the power unit, hand tight only. Do not over tighten. Filter removal The outside surfaces of the power unit, holder and the
ملخص المحتوى في الصفحة رقم 6
with the top of the outlet ring. NB It is possible that the air flow of the power unit when fitted with a fully charged battery pack and a new or servicable filter/pre-filter will be such that when the airflow indicator is located in the outlet ring (See diagram I) it will be expelled. This is not a fault condition but an indication of airflow above the designed limits of the indicator, it is an indication of sufficient airflow. If you have both replaced the filter and fully charged the b
ملخص المحتوى في الصفحة رقم 7
The Power unit will give an audible and visual alarm when either the clogging of the filter(s) causes the airflow to drop to the minimum design flow rate or when the battery voltage drops to a level below which it could not safely power the Power unit. When either of these conditions occur a frequently repeating audible bleep is emitted and in addition the yellow LED on the top of the Power unit flashes if the filter is clogged or the red LED flashes if the battery is low. When either alarm cond
ملخص المحتوى في الصفحة رقم 8
11. GUARANTEE All Magnum Power Units are guaranteed free from any faults in materials or workmanship. Should any such faults develop within 12 months of purchase then Centurion Safety Products Ltd will, at their discretion, repair or replace the unit without charge. 11. SPARES Description Part Number Shower resistant plastic shroud for 8500 unit M23PS Comfort pad ( item 11 ) M23CP/L Spare Standard Belt ( item 1 ) M23B Plastic Belt (Wipe clean for decontamination) item 1 M23PB DIAGRAM OF MAGNUM
