ملخص المحتوى في الصفحة رقم 1
Modelscovered:
Actual product may differ from product pictured above
Blower Kit P/N 7078273
PIN 0-50576
Bagger Kit
P/N 7078274
Weight Kit
P/N 7063375
Complete Kit
Manual No. 7100056 (I.R. 03/31/05)
ملخص المحتوى في الصفحة رقم 2
CllnutlnJllflln$! You have just purchased one of the finest pieces of outdoor power equipment on the market today. If properly cared for, your new Z-Vac Grass Catcher Kit will provide years of dependable service. Please read and follow this instruction man- ual carefully in order to get the most out of your new equipment. As you carefully unpack your unit, you will find the following items: 1 Blower Kit 1 Bagger Kit 1 Weight Kit 1 Package containing operating manuals and warranty registration Ea
ملخص المحتوى في الصفحة رقم 3
ImPS#TMTI7 ## CBgJl! Y mttSWl#8 #JIB BgS#f J$$EmB£1N8 8R8PELq77N8 TRAINING engine before leaving unit. -- Never operate with guards not securely in place. Be sure -- Read, understand, and follow all instructions in the man- all safety features are attached, adjusted properly and func- ual and on the unit before starting. If the operator(s) or tioning properly. mechanic(s) can not read English it is the owner's responsi- -- Never operate with the hose or hood removed or altered. bility to explain
ملخص المحتوى في الصفحة رقم 4
CHILDREN to cool before storing. -- Shut off fuel while storing or transporting. Do not store fuel Tragic accidents can occur if the operator is not alert to the near flames or drain indoors. presence of children. Children are often attracted to the unit -- Keep all hardware tight and keep all parts in good work- and its activity. Never assume that children will remain ing condition. Replace all worn or damaged decals. where you last saw them. -- Never tamper with safety devices. Check their pro
ملخص المحتوى في الصفحة رقم 5
BLOWER KIT INSTALLATION STEP 1: Remove pin, rod and spring securing dis- charge deflector to mower deck, and remove deflector. Store deflector for future use. IMPOR- TANT: Never operate any mower without a dis- charge deflector or grass catcher securely in place. STEP 2: Remove two bolts securing right deck pul- ley guard to mower deck and remove guard. Set REMOVE bolts aside for future assembly step. Store guard for future use. IMPORTANT: Never operate any mower without a pulley guard securely
ملخص المحتوى في الصفحة رقم 6
STEP 6a: Remove bolts securing impeller pulley cover to blower, and remove cover. REMOVE BOLTS, HEN REMOVE OVER STEP 6b: Check to see that blower belt is routed around impeller pulley and idler pulleys after belt is installed onto deck pulley. Then replace cover. Tighten bolts securely. IMPORTANT: Never oper- ate any mower without a pulley guard securely in place. STEP 7: Slip tube of locking pin bracket into blow- er mount, and secure with T-handle pin, making sure pin goes through both upper a
ملخص المحتوى في الصفحة رقم 7
STEP9: Installbeltguardbetween pulleyguard andbeltguardsupportcliponfrontpartof blower mount.Securewith two 5/16nylonwing nuts. Tighten nutssecurely. WEIGHT KIT INSTALLATION !! Warning: Weight kit must be installed prior to installing bagger unit. Failure to do so may result in Iongitudal tipping of unit. STEP 10: Insert the four narrow weight bars through opening in side of foot rest. Be sure holes in weights are all aligned. Next, insert the two 1/2- 13 x 5 bolts through the five wide weight b
ملخص المحتوى في الصفحة رقم 8
INSERT PIN STEP 13: Hook bottom of bagger frame onto pins INTO ROD in bottom of bumper mount plate. Then slide lock- ing rod through aligned holes in bagger flame and bumper mount plate, securing with bridge pin. HOOK BAGGER FRAME ONTO BUMPER MOUNT PLATE PINS STEP 14: Install cross assembly onto bagger CROSS ASSEMBLY frame with four 3/8-16 x 3/4 bolts and hex flange lock nuts, tightening securely. Insert bolts back through bagger frame and into cross assembly. STEP 15: Insert two 5/16-18 x 3/4 b
ملخص المحتوى في الصفحة رقم 9
STEP18: Installbagsontocrossassemblyby hookingslot in baghangerontotabsin channel assembly. STEP19:Closecoverandlockinplacebyhook- inglockknobintoslotincoverlatcharm. STEP20:Sliponehoseclampontoeachendof hose(usetheclampwiththe blackquick-release knobattheblower end),andinstallhosebetween blowerandbagger.Makesureto fit hosesfirmly ontoadapters. Tighten clampssecurely. 9
ملخص المحتوى في الصفحة رقم 10
INTRODUCTION WARNING Follow operation and maintenance instructions in the DO NOT attempt to remove any clogs from deck, blow- Operator's Manual provided with the Snapper CZT/HZT. er, or hose with engine or blade running. STOP engine. STOP blades. Set brake. Remove key. Make sure GRASS CATCHER OPERATION blades and all rotating components have come to a 1. Select desired cutting height. Choose a setting that will complete stop before removing any catcher or unclog- not attempt to cut off too much
ملخص المحتوى في الصفحة رقم 11
IFTHEGRASSCATCHER BECOMES CLOGGED 2. Catcher. Inspect all catcher components. Replace all (ContinuedFromPreviousPage) worn or damaged parts. 3. Catcher Bags. Check bags often for wear or damage. To Clear A Plugged Hose Replace worn or damaged bags immediately, using only 1. Stop blades. Stop engine. Remove key. SNAPPER approved replacement bags. 2. After all rotating components (engine, blower, blades) 4. Deck, Blower, Hose. Clean grass build up from deck, blower, hose, covers and rear cover scr
ملخص المحتوى في الصفحة رقم 12
30 18 22 :\ 27 _25 25 24 24 BLOP_ERUNIT GROUP 25 25 CZT / HZT Models 28 26 * Grease Fitting Orientation 12
ملخص المحتوى في الصفحة رقم 13
CJT/ETmedel$ SntlllllKl-l/tlc lloilr llnl! SrOUll- Item Part No. aty Description 1 1 3046782 WELDMENT, Blower Belt Guard 2 91121 1 NUT, 1/2-13 Hex Nyloc 3 1 90183 WASHER, 1/2" Flat SAE 4 1 3021097 PULLEY, A Groove Idler, Steel 5 1 44995 IDLER STUD (3/8-24 thread) 2 6 91804 FLAT WASHER, 9/16 Type Narrow 7 2 14409 FLANGE BEARING, 9/16" I.D. (powdered metal) 8 10776 1 RETAINING RING, 1/2" 9 1 3046824 BELT RETAINER, Idler 91527 1 10 SCREW, 5/16-18 x 1-1/4" Hex Head Cap, GR5 11 1 3047253 WELDMENT, Id
ملخص المحتوى في الصفحة رقم 14
6 S 4 BLOWER_ G,_JP CZT 1 _T Mo,de_s 14
ملخص المحتوى في الصفحة رقم 15
ClT/l medels apBer l-mc We r mun! 8 #p - Item Part No. aty Description 1 1 3036323 BELT, A Section, 91.125" effective length 2 3037161 1 WELDMENT, Belt Cover, Deck 3 NOT USED 4 2 91537 WING LOCKNUT 5/16-18 5 1 BELT GUARD 3037162 1 6 3046806 PULLEY, Blower Input 7 1 78298 PULLEY, Spindle 8 1 3027505 WELDMENT, Blower Mount 9 1 3027507 WELDMENT, Guard Support Bracket 91541 4 10 SCREW, 5/16-18 x 3/4" Hex Washer Self-Tap 11 1 3027508 WELDMENT, Deck Mount Bracket 12 91304 2 SCREW, 3/8-16 x 1" Hex Hea
ملخص المحتوى في الصفحة رقم 16
t 2 42 \ 3 / / / / 26 25 'Z-VAC' CATCHERGROUP CZT/HZT Models 16
ملخص المحتوى في الصفحة رقم 17
CH/ medel$ apper l- ac Catcher8mm- Item Part No. Qty. Description 3046861 ASSEMBLY, 2 Bag Cover and Screen (includes Item No. la, 5, 12, 13, 14, 42, 43, 44, 45) 18 1 1704033 CATCHER TOP, 2 Bag 2 2 1704180 WINDOW, Cover 3 1 1704405 DECAL, Safety, Grass Bag 4 6 1667248 CLIP, Canoe 5 4 1910531 WASHER, .188 Rivet 1 6 90922 SCREW, #10-32 x 1-1/2 Hex Washer Head Machine w/Nylon Patch 7 91702 3 WASHER, .19 x .38 x .06 Flat 8 1 3021670 STRAP, Rubber 9 90376 5 NUT, #10-32 Hex Nyloc 1 KNOB 10 3022838 11
ملخص المحتوى في الصفحة رقم 18
1 2 See Catcher Group 5 Fastensto RearBumperAssembly of Mower SNAPPER 'Z-VAC' CATCHERMOUNTGROUP CZT /HZT Models 11 18
ملخص المحتوى في الصفحة رقم 19
CH/ medel$ aplmr l-mc CK er mum S lp - Item Part No. Qty. Description 1 3046687 1 WELDMENT, Bagger Mount Frame 2 4 91086 SCREW, 3/8-16 x 3/4" Hex Head Cap, GR5 3 91619 4 NUT, 3/8-16 Hex Flange Lock 4 1 3046831 ARM, Cover Latch 1 4a 3046829 REINFORCEMENT PLATE 5 2 91318 SCREW, 5/16-18 x 3/4" Hex Head Cap, GR5 2 6 91601 NUT, 5/16-18 Hex Flange Lock 7 1 3046995 WELDMENT, Bumper Mounting Plate 8 2 50551 STANDOFF, Bumper Mount 9 4 91318 SCREW, 5/16-18 x 3/4" Hex Head Cap 4 10 91601 NUT, 5/16-18 Hex
ملخص المحتوى في الصفحة رقم 20
Place Against Front of Footrest Slide Through Opening in Footrest 2 WEIGHT BAR GROUP CZT 1 HZT ModeJs 20
