Grizzly T10125 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

model t10125
6" spiral cutterhead
instructions
The Model T10125 spiral cutterhead is designed
to replace the straight knife cutterhead on the
Model G0452 6" jointer.
The total procedure of changing the cutterheads
and setting up the jointer takes approximately
one hour. The job consists of removing the old
cutterhead, installing and shimming the new spi-
ral cutterhead, and readjusting the outfeed table
figure 1. precision straightedges.
even with the carbide inserts at TDC (top dead
cen

ملخص المحتوى في الصفحة رقم 2

6. Wearing heavy leather gloves, carefully installation remove the cutterhead from the casting (see 1. DisConneCT joinTer FroM poWer! figure 5). 2. remove the jointer fence and cutterhead note: Your cutterhead may have paper shims guard. stuck to the bearing block or the part of the casting where the bearing block rests. These 3. remove the V-belt from the pulleys. were included at the factory when they cali- brated your cutterhead even with the outfeed 4. lower both beds to make enough

ملخص المحتوى في الصفحة رقم 3

12. install the cutterhead (figure 6) with the —if the cutterhead is even or within 0.004" lock washers and hex nuts removed in step with the outfeed table from one side to the 5. other, skip to step 18. —if the cutterhead is over 0.004" from one side to the other, go to step 16. 16. loosen the hex nuts securing both bearing block studs, lift the spiral cutterhead slightly, then place a shim beneath the bearing block that needs to be adjusted. note: Use the shims from your old cutterhead

ملخص المحتوى في الصفحة رقم 4

When correctly set, the carbide insert will just insert service touch the straightedge when the insert is at its The Model T10125 6" cutterhead is equipped with highest point of rotation (f igure 10). 32 indexable carbide inserts. each insert can be rotated to reveal any one of its four cutting edges. Therefore, if one cutting edge becomes dull or damaged, simply rotate it clockwise 90˚ to reveal a fresh cutting edge (f igure 11). reference Dot figure 10. using a straightedge to align

ملخص المحتوى في الصفحة رقم 5

t20501—face shield, 4" crown, clear accessories t20502—face shield, 7" crown, clear h7319—10 pack of indexable c arbide inserts t20448—economy clear safety glasses r eplacement carbide inserts for T10125 t20452—"Kirova" anti-reflective glasses cutterhead. t20456—"dakura" clear safety glasses ® h0736—shop fox safety glasses These glasses meet ansi z87.1-2003 specifica- tions. Buy extras for visitors or employees. you can't be too careful with shop safety! t20448 t20452 t20501 figure 12. h7319 i

ملخص المحتوى في الصفحة رقم 6

t10125 parts breakdown and l ist REF PART # DESCRIPTION 1 P0452Z001 DRIVER BIT TORX T20 2 P0452Z002 INDEXABLE INSERT 14 x 14 x 2 3 PFH35M FLAT HD TORX SCR T20 M6-1 X 15 9 P0452Z009 L-WRENCH TORX T20 11 P0452Z011 SPIRAL CUTTERHEAD 6" -6- T10125 6" s piral Cutterhead

ملخص المحتوى في الصفحة رقم 7

Warranty and returns

ملخص المحتوى في الصفحة رقم 8