Vision Fitness X6600iNetTV دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

Assembly
Guide
X6600iNetTV
COMMERCIAL ELLIPTICAL TRAINER

ملخص المحتوى في الصفحة رقم 2

Assembly Guide X6600iNetTV COMMERCIAL ELLIPTICAL TRAINER To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding, find your new Elliptical Trainer’s serial number located on the front axle tube, and enter here: Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Elliptical Trainer. If any parts, har

ملخص المحتوى في الصفحة رقم 3

Screwdriver TOOLS & PARTS INCLUDED MM 6 Allen Wrench MM 5 Allen Wrench MM 8 L-Shaped Wrench PARTS BOX Console Mast Cover, Qty: 1 Water Bottle & Cage, Qty: 1 MM 17 Socket Wrench Heart Rate Chest Strap, Qty:1 Link Arm Covers, Qty: 2 Pedal Support Brackets, Qty: 2 Dual Action End Caps, Qty: 2 Color-coded Hardware Bags Owner’s Guide Assembly Guide Warranty Card CONSOLE BOX iNetTV Console Owner’s Guide MM 10 L-Shaped Wrench

ملخص المحتوى في الصفحة رقم 4

HARDWARE INCLUDED ORANGE BAG BLUE BAG M10x70L CapScrew Quantity: 2 M8x15L Screw Quantity: 2 M20x30x1.5T Wavy Washer Quantity: 2 M8x80L SocketHead CapScrew Quantity: 1 M8x10L Screw Quantity: 4 PINK BAG MM 6 L-Shaped Wrench M5x12L Screw FOR SERVICE ONLY Quantity: 6 M10 Nut Quantity: 2 Link Arm Bushing Quantity: 2 M10x18x2T Washer M5.3x10x1T Washer Quantity: 4 Quantity: 4 M49x7 Round Tool Quantity: 1 M8x30L CapScrew Quantity: 8 M6x40L CapScrew M12x60L CapScrew Quantity: 3 Quantity: 1 M10x40L CapSc

ملخص المحتوى في الصفحة رقم 5

STEP 1 ORANGE BAG • Place the rubber console mast boot on the end of the console mast. • Connect the wire tie that exits the bottom of the console mast to the STEP 1 bundle of wires that comes from the bracket at the top of the frame. Pull the wire tie and wire harness up through the console mast while at the same time inserting the console mast into the frame bracket. • Secure the console mast to the frame with two capscrews (M10 x 70L). MM Tighten with the 8 L-shaped Allen wrench. • Stabiliz

ملخص المحتوى في الصفحة رقم 6

STEP 3 PINK BAG • Connect the right dual-action arm to the right console mast rotation housing, being sure to line up the holes. Secure the dual action arm in place with four screws (M8x30L) and MM tighten with a 6 T-handled Allen wrench. Snap the dual action end cap into place. • Connect the right lower link arm to the right dual-action arm by lining up the holes on the end of each arm. Slide the Link Arm Bushing into the hole of the socket joint. Place a washer (M10.5x18x2t) on the capscrew

ملخص المحتوى في الصفحة رقم 7

STEP 4 CONSOLE • Remove the six mounting screws from the back of the console with the Phillips screwdriver. Set the console in place and secure it to the console mast with the screws you just removed. Connect all the wires to the proper locations in the back of the console (see diagram). STEP 4 1 2 3 4 5 6 7 8 9 WIRES 10 12 13 11 14 1 - Co-Axial Cable TV 2 - USB - B 3 - USB - A 4 - VGA (PC Video) 5 - Video IN 6 - Audio - R 7 - Audio - L 8 - Microphone 9 - Heart Rate Reciever 1 10 - Heart Rate Re