ملخص المحتوى في الصفحة رقم 1
Owner’s Manual
KF-E4.0
Customer Service
(800) 340-0482
Manufactured By:
Keys Fitness Products
4009 Distribution Drive
Suite 250
Garland, TX 75041
CAUTION
Read all precautions and instructions
in this manual before using this
equipment.
Model Name : KF-E4.0
Serial Number :
Serial Number can be found at
the location specified above.
315-00132
09/18 Rev 9.0
ملخص المحتوى في الصفحة رقم 2
www.keysfitness.com TABLE OF CONTENTS THANK YOU for making this unit a part of your exercise program. Keys Fitness Table of Contents 2 Important Safety Information 3 Products Fitness assures the very best in value, appearance, durability and biome- Assembly 4 chanics. This manual will guide you through the assembly process. If at any time Parts Identifier 5 you are having trouble with the assembly or use of this product, then please con- Assembly Steps 6 tact us at our Keys Fi
ملخص المحتوى في الصفحة رقم 3
www.keysfitness.com WARNING! Before using this unit or starting any exercise program, consult your physician. This is especially important for persons over the age of 35 and/or persons with pre-existing health problems. The manufacturer or distributor assumes no responsibility for personal injury or property damage sustained by or through the use of this product. WARNING! To reduce the risk of electrical shock, burns, fire, or other possible injuries to the user, it is important to review this
ملخص المحتوى في الصفحة رقم 4
Assembly www.keysfitness.com 4
ملخص المحتوى في الصفحة رقم 5
www.keysfitness.com A B Main frame Front stabilizer D Right Rotating E1 Upright post Handlebar C Wheel Tracks Left Rotating E2 handlebar Right Stationary G1 Handlebar J L1 (R) K2 Console Pedal assembly (Left) Right Pedal Arm Cover F Water Bottle Water bottle K1 Upright Post Holder H Cover Left Stationary G2 Handlebar L2 (L) Left Pedal Arm Cover Adapter M P1 Allen Screws Allen Screws Rotating Handlebar R1 R2 Pedal Arm Covers - Inner N2 P2 M8x58 M8x70 Covers Pedal Arm Covers - Outer S1 Rot
ملخص المحتوى في الصفحة رقم 6
www.keysfitness.com Use Tool 1 A 6mm ASSEMBLY FOR FRONT STABILIZER Secure the front stabilizer (B) to the main frame (A) using allen 2 screws (R4), 2 spring washers (R17) and 2 flat washers (R15). B R15 R17 R4 6 Assembly
ملخص المحتوى في الصفحة رقم 7
www.keysfitness.com Use Tool ASSEMBLY FOR REAR WHEEL TRACKS 6mm Secure the rear wheel tracks (C) to the main frame (A) using 2 allen screws (R1), 2 spring washers (R13) and 2 flat washers (R14). R1 Note: After finishing the installation of both the front stabilizer bar and the rear wheel tracks, in R13 order to add stability to the unit, you may need to adjust the levelers that are located on the bottom of the stabilizer bars. C R14 Assembly 7
ملخص المحتوى في الصفحة رقم 8
D1-2 www.keysfitness.com D G1 Use Tool G1-1 Use Tool G2 R6 6mm 5mm H 3 ASSEMBLY FOR UPRIGHT POST D Step 1: G2 Insert the upright post cover (H) into the upright post (D) from the bottom side. D2 R14 Step 2: R7 Connect the lower sensor wire (A2) with the upper sensor wire (D2). Step 3: R13 A2 Mount the upright post (D) to the main frame (A) and secure using 4 screws (R7), 4 spring washers (R13), and 4 flat washers (R14). A Step 4: Slide the upright post cover down to conceal tube connection
ملخص المحتوى في الصفحة رقم 9
www.keysfitness.com E1 Use Tool 4 D1-3 E1-1 ASSEMBLY FOR RIGHT ROTATING E1-1 HANDLEBAR AND HANDLEBAR TUBE 6mm Step 1: Insert ring seal (R19) and flat washer (R23) into the right arm joint of the upright post. R3 R13 R14 Step 2: l ocate the right rotating arm (S1) and connect it to the upright post (D) at the arm joint and secure using allen screw (R8), spring washer (R16) and flat washer (R21). D1-3 S1 R23 Step 3: S1 Attach the right rotating handlebar (E1) to the R16 right rotating arm
ملخص المحتوى في الصفحة رقم 10
www.keysfitness.com R13 Use Tool R22 S1 R14 6mm R2 Use Tool 5 13mm 14mm ASSEMBLY FOR RIGHT ROTATING HANDLEBAR TUBE Step 1: Insert 2 bushings (R18) on the tapered ends into the S1 right pedal arm joint (A) - one for each side. Step 2: Attach the right pedal arm (A) to the right rotating han- dlebar tube (S1) and secure using allen screw (R2), R18 flat washer (R14), spring washer (R13) and nut (R22). 10 Assembly A A
ملخص المحتوى في الصفحة رقم 11
www.keysfitness.com D S2 Use Tool D R23 6mm S2 6 R8 ASSEMBLY FOR LEFT ROTATING HANDLEBAR TUBE Step 1: R16 Insert ring seal (R19) and flat washer (R23) into the left R19 arm joint of the upright post. R21 Step 2: l ocate the left rotating arm (S2) and connect it to the upright post (D) at the arm joint and secure using allen screw (R8), spring washer (R16) and flat washer (R21). R16 R20 ASSEMBLY FOR LEFT PEDAL l ocate the left pedal assembly (F) and attach it to the main frame (A) at the
ملخص المحتوى في الصفحة رقم 12
www.keysfitness.com Use Tool D 7 6mm S2 ASSEMBLY FOR LEFT ROTATING HANDLEBAR TUBE Use Tool Step 1: Insert 2 bushings (R18) on the tapered ends into the left pedal 13mm arm joint (F) - one from each side. 14mm Step 2: Attach the left pedal arm (F) to the left rotating handlebar tube (S2) and secure using allen screw (R2), spring washer (R13), flat washer (R14) and nut (R22) . S2 R14 R13 R22 R2 R18 F R18 12 Assembly A
ملخص المحتوى في الصفحة رقم 13
www.keysfitness.com J J1 J J1 E2 8 D D1-3 Use Tool ASSEMBLY FOR WATER BOTTLE HOLDER E2-1 Step 1: Attach the water bottle holder (K2) and secure to K1 the upright post (D) using 2 screws (R5). R3 6mm R13 Step 2: R14 Use Tool Place water bottle (K1) inside water bottle holder (K2). 13mm S2 14mm ASSEMBLY FOR CONSOLE Step 1: K2 Remove 2 screws (J1) from the back of the console. R5 Step 2: Connect the pulse wires, sensor wires and the ASSEMBLY FOR LEFT ROTATING HANDLEBAR toggle wires wit
ملخص المحتوى في الصفحة رقم 14
www.keysfitness.com Use Tool 6mm S1 9 L1 R10 ASSEMBLY FOR RIGHT PEDAL ARM COVER Step 1: Attach the pedal arm cover (l 1) to the pedal arm joint and secure with screw (R9). Step 2: P2 P1 Repeat on left side with left pedal arm cover (l 2). R12 ASSEMBLY FOR ROTATING HANDLEBAR TUBE COVER Step 1: Attach the inner rotating handlebar tube cover (P1) and the outer rotating handle- bar tube cover (P2) to the handlebar tube joint and secure with 2 screws (R9). Step 2: Repeat on left side with rotati
ملخص المحتوى في الصفحة رقم 15
www.keysfitness.com D N1 N2 R10 10 ASSEMBLY FOR HANDLEBAR COVERS N1 Step 1: Attach the handlebar cover (N2) to the left handlebar joint at the rear of the unit and secure with screw (R10). R10 Step 2: Attach the handlebar cover (N1) to the left handlebar joint at the front of the unit and secure with screw (R10). Step 3: N2 Repeat steps 1 and 2 for the right handlebar. Use Tool 6mm Assembly 15
ملخص المحتوى في الصفحة رقم 16
www.keysfitness.com Congratulations! You have completed the assembly of your new Keys Fitness E4.0 Elliptical! ADAPTER PLUG-IN LOCATION Adapter (M) TRANSPORTING YOUR UNIT TRANSPORT WHEELS 16 Assembly
ملخص المحتوى في الصفحة رقم 17
Console Information www.keysfitness.com 17
ملخص المحتوى في الصفحة رقم 18
www.keysfitness.com CONSOLE BUTTONS MODE: This button is used as an enter key, and will allow user to move to the next setting that can be changed. When pressed and held for 2 seconds or more, console will go back to the user profile selection screen. RESET: This button is used to return to program selection screen when workout is paused by pressing start/stop button. START/STOP: This button is used to start or stop training. RECOVERY: This button is used to begin the Recovery feature
ملخص المحتوى في الصفحة رقم 19
www.keysfitness.com BUTTONS ON ROTATING HANDLEBAR In order to offer more flexibility during your workout, additional toggle switches are placed on the rotating handlebar. The buttons are the +/- and Mo DE/ENTER. They are used the same way as the buttons on the console. These buttons may be used at anytime as a substitute to pressing the buttons located on the console. CONSOLE FUNCTIONS TIME: If a target time was not selected, time will count up from 00:00 to maximum 99:59. When working out w
ملخص المحتوى في الصفحة رقم 20
www.keysfitness.com WATT: Displays current training watt figures. A watt is a measurement of the amount of power generated by the user based on the resistance and speed. RECOVERY: After your workout, press “RECo VERY” button and keep holding on hand grips. All function display will stop except “TIME” starts counting down from 00:60 to 00:00. Screen will display your heart rate recovery status rating between F1-F6. F1 is the best, F6 is the worst. User may keep exercising to improve the heart
