ملخص المحتوى في الصفحة رقم 1
PERFORMANCE
SERIES
FOR MODELS :
PSE7
ELLIPTICAL USER’S GUIDE
ملخص المحتوى في الصفحة رقم 2
ملخص المحتوى في الصفحة رقم 3
INTRODUCTION CONGRATULATIONS and THANK YOU for your purchase of this Performance Series elliptical! Whether your goal is to win races or simply enjoy a fuller, healthier lifestyle, a Performance Series elliptical can help you attain it – adding club-quality performance to your at-home workouts, with the ergonomics and innovative features you need to get stronger and healthier, faster. Because we're committed to designing fitness equipment from the inside out, we use only the highest quality
ملخص المحتوى في الصفحة رقم 4
IMPORTANT BEFORE BEFORE ELLIPTICAL CONDITIONING TROUBLESHOOTING LIMITED INTRODUCTION ASSEMBL ASSEMBLY Y PRECAUTIONS YOU YOU BEGIN BEGIN OPERATION GUIDELINES & MAINTENANCE WARRANTY IMPORTANT PRECAUTIONS SAVE THESE INSTRUCTIONS Read all instructions before using this elliptical. When using an electrical product, basic precautions should always be followed, including the following: Read all instructions before using this elliptical. It is the responsibility of the owner to ensure that all users o
ملخص المحتوى في الصفحة رقم 5
ASSEMBLY IMPORTANT: READ THESE SAFETY INSTRUCTIONS BEFORE USE! WARNING There are several areas during the assembly process of an elliptical that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the elliptical could have frame parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the ellipt
ملخص المحتوى في الصفحة رقم 6
IMPORTANT BEFORE BEFORE ELLIPTICAL CONDITIONING TROUBLESHOOTING LIMITED INTRODUCTION ASSEMBLY PRECAUTIONS YOU YOU BEGIN BEGIN OPERATION GUIDELINES & MAINTENANCE WARRANTY LEFT HANDLEBAR ACCESSORY TRAY BOTTLE HOLDER CONSOLE GRIP PULSE RIGHT HANDLEBAR CONSOLE MAST HANDLEBAR COVERS CONSOLE MAST BOOT TOP COVER LOWER HANDLEBAR FRONT STABILIZER TUBE ELBOW COVER LOWER LINK ARM PIVOTING FOOT PAD PEDAL ARM TOOLS INCLUDED PARTS INCLUDED c 6 Hardware Bags c 5mm Allen Wrench c 1 Console c 2 Handlebar Cove
ملخص المحتوى في الصفحة رقم 7
ASSEMBLY STEP 1 FRONT STABILIZER TUBE BOLT (A) MAIN FRAME BOLT (B) GUIDE RAILS A) Open HARDWARE BAG FOR STEP 1. B) Extend the GUIDE RAILS away from the MAIN FRAME until bolt holes line up. C) Secure GUIDE RAILS using 2 BOLTS (B). D) Attach the FRONT STABILIZER TUBE to the MAIN FRAME using 2 BOLTS (A). HARDWARE BAG FOR STEP 1 CONTENTS : BOLT (A) BOLT (B) 20 mm 15 mm Qty: 2 Qty: 2 7 LIMITED TROUBLESHOOTING CONDITIONING ELLIPTICAL BEFORE IMPORTANT ASSEMBLY INTRODUCTION WARRANTY & MAINTENANCE GUIDEL
ملخص المحتوى في الصفحة رقم 8
IMPORTANT BEFORE BEFORE ELLIPTICAL CONDITIONING TROUBLESHOOTING LIMITED INTRODUCTION ASSEMBLY PRECAUTIONS YOU YOU BEGIN BEGIN OPERATION GUIDELINES & MAINTENANCE WARRANTY ASSEMBLY STEP 2 CONSOLE WIRES BOLT (B) CONSOLE MAST SPRING WASHER (C) FLAT WASHER (D) CONSOLE MAST BOOT MAIN FRAME A) Open HARDWARE BAG FOR STEP 2. B) Slide CONSOLE MAST BOOT onto the bottom of the CONSOLE MAST. C) Carefully pull the CONSOLE WIRES through the CONSOLE MAST using the twist tie located inside the CONSOLE MAST. D)
ملخص المحتوى في الصفحة رقم 9
ASSEMBLY STEP CONSOLE MAST BOOT TOP COVER MAIN FRAME NOTE: There is NO hardware bag for this step. A) Carefully snap TOP COVER into the MAIN FRAME. B) Slide CONSOLE MAST BOOT down over the TOP COVER. LIMITED TROUBLESHOOTING CONDITIONING ELLIPTICAL BEFORE IMPORTANT ASSEMBLY INTRODUCTION WARRANTY & MAINTENANCE GUIDELINES OPERATION YOU BEGIN PRECAUTIONS
ملخص المحتوى في الصفحة رقم 10
IMPORTANT BEFORE BEFORE ELLIPTICAL CONDITIONING TROUBLESHOOTING LIMITED INTRODUCTION ASSEMBLY PRECAUTIONS YOU YOU BEGIN BEGIN OPERATION GUIDELINES & MAINTENANCE WARRANTY ASSEMBLY STEP LINK ARM WAVY WASHER (E) BOLT (B) FOOT PAD BRACKET PEDAL ARM A) Open HARDWARE BAG FOR STEP 4. B) Place WAVY WASHER (E) over the LINK ARM axle. C) Slide the LINK ARM into the PEDAL ARM. D) Attach FOOTPAD BRACKET to the LINK ARM with 3 BOLTS (B). E) Repeat on other side. HARDWARE BAG FOR STEP CONTENTS : WAVY WAS
ملخص المحتوى في الصفحة رقم 11
ASSEMBLY STEP RUBBER INSERTS SCREWS (F) FOOT PAD LINK ARM A) Open HARDWARE BAG FOR STEP 5. B) Attach FOOTPAD to LINK ARM using 4 SCREWS (F). C) Peel backing from RUBBER INSERT and carefully place on top of FOOTPAD. D) Repeat on other side. HARDWARE BAG FOR STEP CONTENTS : SCREW (F) 12 mm Qty: 8 11 LIMITED TROUBLESHOOTING CONDITIONING ELLIPTICAL BEFORE IMPORTANT ASSEMBLY INTRODUCTION WARRANTY & MAINTENANCE GUIDELINES OPERATION YOU BEGIN PRECAUTIONS
ملخص المحتوى في الصفحة رقم 12
IMPORTANT BEFORE BEFORE ELLIPTICAL CONDITIONING TROUBLESHOOTING LIMITED INTRODUCTION ASSEMBLY PRECAUTIONS YOU YOU BEGIN BEGIN OPERATION GUIDELINES & MAINTENANCE WARRANTY ASSEMBLY STEP LEFT HANDLEBAR PRE-ATTACHED BOLT AND WASHERS RIGHT HANDLEBAR NOTE: There is NO hardware bag for this step. All hardware is pre-installed. A) Remove PRE-ATTACHED BOLT & WASHERS from CONSOLE MAST. B) Slide RIGHT HANDLEBAR onto CONSOLE MAST and attach by re-inserting PRE-ATTACHED BOLT & WASHERS. C) Repeat on other
ملخص المحتوى في الصفحة رقم 13
ASSEMBLY STEP 7 LOWER LOWER LINK ARM HANDLEBAR TEFLON WASHERS SPACER LOWER HANDLEBAR BOLT (G) SPACER (H) LOWER LINK ARM SPACER RINGS (I) WASHER (J) NUT (K) LOWER LINK ARM GUIDE RAIL A) Open HARDWARE BAG FOR STEP 7. B) Slide SPACER (H) into LOWER LINK ARM. C) Place SPACER RING (I) on either side of SPACER (H). While holding SPACER RING (I) slide LOWER LINK ARM into bottom end of LOWER HANDLEBAR. D) Insert BOLT (G) into LOWER HANDLEBAR and secure using WASHER (J) and NUT (K). E) Repeat on other
ملخص المحتوى في الصفحة رقم 14
IMPORTANT BEFORE BEFORE ELLIPTICAL CONDITIONING TROUBLESHOOTING LIMITED INTRODUCTION ASSEMBLY PRECAUTIONS YOU YOU BEGIN BEGIN OPERATION GUIDELINES & MAINTENANCE WARRANTY ASSEMBLY STEP SCREW (L) INSIDE ELBOW COVER OUTSIDE ELBOW COVER A ) Open HARDWARE BAG FOR STEP 8. B) Attach the OUTSIDE ELBOW COVER to the elbow joint using 1 SCREW (L). C) Snap the INSIDE ELBOW COVER onto the OUTSIDE ELBOW COVER. Note the position of the snap tabs before snapping into position. D) Repeat on other side. HAR
ملخص المحتوى في الصفحة رقم 15
ASSEMBLY STEP RIGHT HANDLEBAR PRE-ATTACHED SCREW HANDLEBAR COVERS NOTE: There is NO hardware bag for this step. All hardware is pre-installed. A) Remove PRE-ATTACHED SCREW from the RIGHT HANDLEBAR. B) Snap HANDLEBAR COVERS together over the RIGHT HANDLEBAR. Note the position of the snap tabs on the covers before snapping into position. C) Attach HANDLEBAR COVERS with PRE-ATTACHED SCREW. D) Repeat on other side. 1 LIMITED TROUBLESHOOTING CONDITIONING ELLIPTICAL BEFORE IMPORTANT ASSEMBLY INT
ملخص المحتوى في الصفحة رقم 16
IMPORTANT BEFORE BEFORE ELLIPTICAL CONDITIONING TROUBLESHOOTING LIMITED INTRODUCTION ASSEMBLY PRECAUTIONS YOU YOU BEGIN BEGIN OPERATION GUIDELINES & MAINTENANCE WARRANTY ASSEMBLY STEP 10 NOTE: There is NO hardware bag for this CONSOLE step. All hardware is pre-installed. A) Attach the CONSOLE MAST wires to the CONSOLE wires. CONSOLE WIRES B) Carefully tuck the CONSOLE MAST wires into the CONSOLE MAST before attaching PRE-ATTACHED CONSOLE MAST the CONSOLE. SCREWS C) Attach CONSOLE to the CON
ملخص المحتوى في الصفحة رقم 17
BEFORE YOU BEGIN CONGRATULATIONS! on choosing your elliptical. You’ve taken an important step in developing and sustaining an exercise program! Your elliptical is a tremendously effective tool for achieving your personal fitness goals. Regular use of your elliptical can improve the quality of your life in so many ways. HERE ARE jUST A FEW OF THE HEALTH BENEFITS OF ExERCISE: • Weight Loss • A Healthier Heart • Improved Muscle Tone • Increased Daily Energy Levels The key to reaping these benef
ملخص المحتوى في الصفحة رقم 18
IMPORTANT BEFORE BEFORE ELLIPTICAL ELLIPTICAL CONDITIONING TROUBLESHOOTING LIMITED INTRODUCTION ASSEMBL ASSEMBLY Y PRECAUTIONS YOU YOU BEGIN BEGIN OPERA OPERATION TION GUIDELINES & MAINTENANCE WARRANTY ELLIPTICAL OPERATION POWER Your programmable elliptical is powered by a power supply. The power must be plugged into the power jack, which is located in the front of the machine near the STABILIZER TUBE. Make sure the console power switch is in the ON position. Note: Not all units have an ON/OFF
ملخص المحتوى في الصفحة رقم 19
PSE7 CONSOLE DISPLAY J H A J P R E S S T O S W I T C H P E R F O R M A N C E T R A C K I N G P R O G R A M S WEIGHT REVERSE MANUAL INTERVALS ROLLING RANDOM CUSTOM 1 CUSTOM 2 LOSS TRAIN E I ™ e T R A K I N S T R U C T I O N S Upon initial start, press Press the eTRAK Current Workout To reset: Press and and hold eTRAK to activate button to scroll Average Workout hold ENTER for through options: Last Workout ten seconds (From this point on, eTRAK will Lifetime Total accumulate info unless reset) R
ملخص المحتوى في الصفحة رقم 20
IMPORTANT BEFORE BEFORE ELLIPTICAL ELLIPTICAL CONDITIONING TROUBLESHOOTING LIMITED INTRODUCTION ASSEMBL ASSEMBLY Y PRECAUTIONS YOU YOU BEGIN BEGIN OPERA OPERATION TION GUIDELINES & MAINTENANCE WARRANTY PSE7 CONSOLE OPERATION QUICK START 1) Turn on Elliptical. 2) Press START button and begin exercising. ) Program will automatically default to MANUAL (P1), the time will count up from 0:00, and the resistance will default to level 1. ) The resistance level can be adjusted during the workou
