ملخص المحتوى في الصفحة رقم 1
™
SaphIR K2 Keypad
Instruction Manual
ملخص المحتوى في الصفحة رقم 2
SAFETY PRECAUTIONS For your safety, please read and follow these precautions ➤ Ground device properly. Make sure the device’s means of before installing or using this product: grounding or polarization is not defeated. ➤ Read instructions. Read and understand all the applicable ➤ Keep device clean. From time to time, wipe off the device instructions before installing or operating the device. with a clean soft cloth. Don’t use abrasive materials, thin- ners, alcohol or other chemical solvents or
ملخص المحتوى في الصفحة رقم 3
TABLE OF CONTENTS USER SECTION 4–9 Source Select Command Procedure 34 Introduction 4 Power Management Procedure 35 Features and Key Guide 5 Macro Editor Procedure 38 SYSTEM MENU 40 Optional SRC1 Basic Remote Control 6 Keypad ID Procedure 40 Optional SRC2 Advanced Learning Remote Control 7 Copy Configuration Procedure 40 Keypad Operation 8 System Information Procedure 41 INSTALLER SECTION 10–55 Update Firmware Procedure 42 Getting Started 10–12 Factory Initialization Procedure 42 Installation Ove
ملخص المحتوى في الصفحة رقم 4
USER Introduction Product Overview Features ™ • Simple design and intuitive layout Thank you for choosing the Russound SaphIR K2 keypad. The K2 is an in-wall programmable IR keypad that works like a uni- • Selects and controls up to eight sources versal remote to provide complete control of your audio and • Backlit LCD display shows selected source video components. It contains an extensive library of IR codes to select discs, tracks, channels, volume, and other settings for • Selectable green o
ملخص المحتوى في الصفحة رقم 5
USER Features and Key Guide 1 7 2 6 3 5 4 1 DISPLAY – 12-character backlit LCD panel shows 5 COMMAND KEYS – Control the source equipment source name and other information 6 POWER KEY – Turns keypad on or off when 2 SOURCE SELECT KEY – Selects the desired source pressed once; turns all keypads on or off when connected to the amp/receiver pressed a second time and held 3 VOLUME UP/DOWN KEYS – Control the volume of 7 F1 AND F2 KEYS – Set and select user’s Favorite 1 the amp/receiver and Favorite 2
ملخص المحتوى في الصفحة رقم 6
USER Optional SRC1 Basic Remote Control 1 1 POWER KEY – Turns the keypad on and off. Press and hold for All On or All Off function. 2 NUMERIC KEYS – For direct selection of channels or tracks. 2 3 VOLUME UP/DOWN KEY – Raises and lowers the amp/receiver volume. 4 COMMAND KEYS – Control the source equipment. 8 5 DIRECT SOURCE SELECT KEYS – Directly select sources 1– 6 controlled by the keypad. 3 6 F1 AND F2 KEYS – Set and select Favorite 1 and Favorite 2 presets. 7 CURSOR KEYS – Issue navigation c
ملخص المحتوى في الصفحة رقم 7
USER Optional SRC2 Advanced Learning Remote Control 1 1 POWER KEY – Turns the keypad on and off while in System mode. Press and hold for All On or All Off function. 11 2 2 SYSTEM MODE KEY – Selects System mode to control the SaphIR K2 keypad and connected sources. The remote must be in System mode to work with the SaphIR K2 keypad. 3 10 NUMERIC KEYS – For direct selection of channels or tracks. 3 4 VOLUME UP/DOWN KEY – Raises and lowers the amp/receiver volume. 5 COMMAND KEYS – Control the sourc
ملخص المحتوى في الصفحة رقم 8
USER Keypad Operation On/Off turn off. If power management is set up on your keypad, Press and release to turn on the K2 keypad. This the All Off command will turn off your amp/receiver and will also activate any speakers wired through the speak- source components. er relay on the back of the K2. If power management is System On Indicator set up on your keypad, turning on the keypad will also When a keypad is off but the connected audio system is turn on your amp/receiver and source components.
ملخص المحتوى في الصفحة رقم 9
USER Keypad Operation F1 and F2 Keys source at the K2 Keypad. The command keys are acti- The and preset keys are for saving and recall- vated with a press and release, or with a press and hold ing a source selection and favorite disk or channel. to access secondary functions. To save a preset, first select a source. Next, press and User Menu hold the or key until SAVED appears on the dis- The User Menu allows you to adjust the keypad back- play. This saves the source selection. Within 15 second
ملخص المحتوى في الصفحة رقم 10
INSTALLER Getting Started About this Section Terms You Need to Know The rest of this manual provides technical information for installing and Amp/Receiver – The central receiver, preamplifier, or programming the SaphIR K2 keypad. This section is intended mostly amplifier to which the source components in the audio for installers, but users may find the information useful as well. system are connected. This component is operated from the SaphIR K2 keypad to provide the source selec- Installation
ملخص المحتوى في الصفحة رقم 11
INSTALLER Getting Started web site and uploaded into the keypad by using the Firmware that allows the creation of up to 132 macros, each of which Update procedure in the System Menu. This requires connect- can contain up to 10 command steps. ing a computer to the keypad with a Programming Cable, part Numeric IR – A procedure in the Source Setup menu that pro- number 2500-121036. grams the plus and minus keys to scroll through channel or Input Order – The order in which the amp/receiver selects i
ملخص المحتوى في الصفحة رقم 12
INSTALLER Getting Started Typical System Configuration The SaphIR K2 keypad requires an IR connecting block such as the Russound 857 for power and communication with the compo- IN nents and other K2 keypads. The amp/receiver and other devices receive commands from the 857 connecting block through 845.1 Stand Alone IR Keypad SaphIR K2 or 1584.1 micro emitters or by direct connection to IR input jacks on the components. Back of SaphIR K2 See connection The Russound 1201A power sup- close-up on pl
ملخص المحتوى في الصفحة رقم 13
INSTALLER Keypad Installation Tools Needed for Installation Considerations 1 • Drill with a ⁄2-inch drill bit • For best infrared remote performance, locate the keypad away from direct sunlight, plasma TVs, lighting controls, and high- and low-voltage wiring. Also consider con- • Keyhole saw venience when choosing a location. • Flat-head screwdriver (medium size) • When running cables, avoid locations concealing pipes, heating ducts and AC • Phillips screwdriver (cordless recommended) wiring
ملخص المحتوى في الصفحة رقم 14
INSTALLER Keypad Connections IR and Power Connections 1 The K2 keypad can be connected using either CAT-5 or shielded 4- conductor, 22-gauge 2-twisted-pair 2 cable. The maximum recommended cable length is 250 feet for either Leave 3 type of cable. See page 15 for the shield wiring color codes for both cables. open 4 IN • When using shielded 22/4 cable, use one twisted pair for power and ground, and the other twist- ed pair for status and IR signal. 5 Shielded 22/4 Always leave the shield open
ملخص المحتوى في الصفحة رقم 15
INSTALLER EZB-1SC Connections Top View EZB-1SC Connection EZB-1SC Details Shielded 22/4 Cable When using shielded 22/4 two-twisted-pair cable, use Wire Color Function one twisted pair for power Red +12V and ground, and the other twisted pair for status and Black Ground IR signal. Always drain the Green IR Signal shield by connecting it or White Status Shielded 22/4 the drain wire to the GND terminal on the EZB con- Connection Bare Drain (Gnd) necting block. to EZB-1SC Snap Connector Note: To ens
ملخص المحتوى في الصفحة رقم 16
INSTALLER Multiple 857 Connections Multiple 857 To SaphIR K2 keypads Connections Multiple groups of up to four K2 keypads can be linked together by using successive Russound 857 IR connecting blocks as shown in the dia- gram to the left. Each IR con- necting block must have its own 1201A power supply. Each Russound 1201A power supply supports a maximum of four K2 keypads. When using shielded 22/4 cable, use one twisted pair for power and ground, and the other twisted pair for status and IR sig
ملخص المحتوى في الصفحة رقم 17
INSTALLER Multiple 857 Connections Note: Do not connect the +12VDC wire between the 857 connecting blocks. Each 857 requires its own 1201A power supply. Only GND, SIGNAL and STATUS need to be connected between multiple connecting blocks. Source IR emitters can be connected to any connecting block in this arrangement. 857 857 857 to EZB IR COMMO IR COMMON IN 857 to EZB +12VDC +12VDC GND GND STATUS STATUS SIGNAL DESIG SIGNAL D Shielded 22/4 Connection to 857 Screw Terminals From 857 to next
ملخص المحتوى في الصفحة رقم 18
INSTALLER Programming Port Programming Port The Programming Port is used for programming the SaphIR K2, backing up the keypad configuration, and updating the keypad firmware with a Windows-based computer. These pro- 1 cedures require a Programming Cable, Russound part num- ber 2500-121036. DATA Keypad Programming The SaphIR K2 can be programmed by using Russound’s free DATA EZpro software on a computer. You can download EZpro from GND the Infrared Products page in the Document Center at www.russ
ملخص المحتوى في الصفحة رقم 19
INSTALLER Programming Overview Programming Methods There are two ways to program the SaphIR K2 keypad. The easier method is to use EZpro software on a connected Windows-based computer, but you can also program the keypad manually using the programming menu described in this section. The menu is organized in a file tree structure similar to that found on a computer. At each subsequent level, options become more specific. The menu procedures provide intuitive options and navigation, allowing you t
ملخص المحتوى في الصفحة رقم 20
INSTALLER Programming Overview mands from the remote control. The commands are central- Recommended Process ly stored in the keypad as a learned IR command type. It will be much easier to program the SaphIR K2 if you follow the steps in a particular order, especially if you’re programming it 6. Number of Sources (page 27) – If the system has fewer manually. Here’s the order we recommend for initial setup: than eight sources, specify the total number of sources to prevent unused source numbers fr
