ملخص المحتوى في الصفحة رقم 1
PLCD10CH
OPERATING
INSTRUCTIONS
Disc Magazine
10
Open Compact Disc Changer System
DIGITAL AUDIO
Disc Auto Changer
COMPACT DISC CHANGER
Compact Disc Auto Changer
ملخص المحتوى في الصفحة رقم 2
CONTENTS HINTS FOR CORRECT AND SAFE OPERATION 2 HOW TO USE THE MAGAZINE 3 PRECAUTIONS FOR HANDLING DISCS 4 INSTALLATION PARTS 5 WIRING 5 RESET FUNCTION 5 BEFORE INSTALLING THE UNIT 6 • Transport Lock Screws 6 • Installation and Wiring Precautions 6 • Position of the built-in anti-vibration Board 7 INSTALLATION 8 • Procedure for Installation on Carpet (Horizontal Position) 8 • Procedure for Installation on Carpet (Vertical Position) 9 • Procedure for Installation on Carpet (At a 45° angle) 10 • P
ملخص المحتوى في الصفحة رقم 3
HOW TO USE THE MAGAZINE Loading a disc 1. Pick the tab on the magazine’s disc tray and pull out only of the trays. 2. Place the disc on the tray with its play surface facing down (label surface facing up). Label side up • Each tray can accommodate only one disc. 3. Press the tab on the disc tray to store the tray back in the magazine. • Up to ten discs can be loaded. Play side down Installing the magazine 1. Slide the door toward the right. 2. First check that the magazine with the discs has its
ملخص المحتوى في الصفحة رقم 4
PRECAUTIONS FOR HANDLING DISCS With new discs The symptoms described below sometimes occur when new discs are used: • The disc is not played even Burrs when it is loaded. Center • Operation changes to the next hole Burrs disc before the first disc has a chance to be played. Outside • The same disc is played over circmference and over again. • The designated disc is not played. Remove all plastic particles of burr from surfaces of disc before loading in magazine. These symptoms occur when t
ملخص المحتوى في الصفحة رقم 5
INSTALLATION PARTS Bracket (A) Bracket (B) Hexagonal Bolt Truss Screw (M6 x 12) (M4 x 5) x 2 x 2 x 4 x 4 Tapping Screw DIN 8 Seal Double (M5 x 12) Pin Cable Sided Tape x 4 x 1 x 1 x 2 WIRING Connect this cable to the terminal of the CD player. RESET FUNCTION The reset button must be activated with either a ball point pen or thin metal object. It is to be activated for the following reason: • Initial installation of the unit when all wiring is completed. • Some functions do not operate. Reset
ملخص المحتوى في الصفحة رقم 6
BEFORE INSTALLING THE UNIT Transport Lock Screws The mechanism in the CD changer is “locked” into place during shipment by the transport screws. Be sure to remove the screws prior to installation. Caution After removing the transport lock screws, place the supplied seals over the screw holes. These seals are used to keep dust, which could cause a malfunction, out of the unit. Installation and Wiring Precautions 1. To prevent a short-circuit. • Be sure to turn off the ignition and remove the nega
ملخص المحتوى في الصفحة رقم 7
0 45 0 Position of the built-in anti-vibration board This unit can be installed horizontally (suspended), vertically, and at a 45° angle. Once the installation position has been decided, it’s necessary to set the position of the built-in anti-vibration board inside the unit. Please do this before performing the procedure listed below. Vibration may cause the disc to skip if the unit is used before properly setting the anti-vibration board. • At the time of shipping, the built-in anti-vibration
ملخص المحتوى في الصفحة رقم 8
INSTALLATION Procedure for Installation on Carpet (Horizontal Position) • Confirm that the built-in 1 anti-vibration boards on both the left Built-in anti-vibration board position and right sides are set to the horizontal installation position “0”. Hexagon bolts (M6 x 12) • Attach the left and right brackets (A) using the hexagonal bolt (M4 x 5). • Attach the left and right brackets (A) to their respective brackets (B) using the hexagonal bolts (M6 x 12) and the hexagonal nuts (M6). Hexagonal
ملخص المحتوى في الصفحة رقم 9
INSTALLATION Procedure for Installation on Carpet (Vertical Position) • Set that the built-in anti-vibration 1 boards on both the left and right Built-in anti-vibration board position sides are set to the vertical installation position “90”. Hexagon bolts (M6 x 12) • Attach the left and right brackets (A) using the hexagonal bolt (M4 x 5). • Attach the left and right brackets (A) to their respective brackets (B) using the hexagonal bolts (M6 x 12) and the hexagonal nuts (M6). Hexagonal bolts
ملخص المحتوى في الصفحة رقم 10
INSTALLATION Procedure for Installation on Carpet (at a 45° angle) • Set the built-in anti-vibration boards 1 on both the left and right sides to Built-in anti-vibration board position the 45° installation position “45°”. • Attach the left and right brackets (A) Hexagon bolts (M6 x 12) using the hexagonal bolt (M4 x 5). • Attach the left and right brackets (A) to their respective brackets (B) using the hexagonal bolts (M6 x 12) and the hexagonal nuts (M6). Hexagonal bolts (M4 x 5) • Pull back
ملخص المحتوى في الصفحة رقم 11
INSTALLATION Procedure for Installation (Suspended Position) • Confirm that the built-in 1 anti-vibration boards on both the left Built-in anti-vibration board position and right sides are set to the horizontal installation position “0”. • Attach the left and right brackets (A) using the hexagonal bolt (M4 x 5). Hexagonal Bolts Hexagonal Bolts • Determine the mounting location • Attach the CD changer with the 2 3 and drill four mounting holes. tapping screws (M5 x 12). 3.6ø 11
ملخص المحتوى في الصفحة رقم 12
HANDLING THE DISCS Dirt, dust, scratches and warpage cause sound skips during playback and a deterioration of sound quality. How to take care of your disc: 1. Use compact discs that have the mark shown on the right. 2. Fingerprints and dust should be carefully wiped off the disc’s signal surface (glossy side) with a soft cloth. Unlike conventional records, the compact disc has no grooves to collect dust and microscopic debris, so gently wipe with a soft cloth should remove most particles. W
