ملخص المحتوى في الصفحة رقم 1
Model No.
680.84973
0
€
Save This Manuat For Future Reference
CAUTION: Read rules for safe operation and instructions carefu[ty
SoW by SEARS, ROEBUCK AND CO., Chica_o, IL 60179 U.S.A
ملخص المحتوى في الصفحة رقم 2
IMPORTANT SAFETY INSTRUCTIONS This Rug shampooer/ftoor potisher is for househotd use onty. When using etectrica[ Rug shampooer/ftoor potisher, basic precautions should be followed. Inctuding the fottowing READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE To reduce risk of fire, electric shock, or injury • DO NOT USE FLAMABLE OR COMBUSTIBLE LIQUIDS, SUCH AS GASOLINE, OR USE IN AREAS WHERE THEY MAY BE PRESENT. • Do not reave this apptiance when ptugged in. • To reduce the risk of etectric shock-Us
ملخص المحتوى في الصفحة رقم 3
,SEARS Dear Homemaker: You have just invested in a fine Kenmore Rug Shampooer-,Ftoor Polisher. Before using your new Kenmore machine, please pause for a moment and carefully read this booklet, which contains instructions on how to operate and care for your machine. Specific instructions are given on rug shampooing, scrubbing, polishing, attachin8 and cleaning brushes, etc. This wi[[ help you to obtain the best performance and avoid unnecessary service expense for conditions beyond our control El
ملخص المحتوى في الصفحة رقم 4
DO NOT PLUG IN ELECTRIC CORD UNTIL BRUSHES OR OTHER ACCESORIES HAVE BEEN ATTACHED AND SWITCH HAS BEEN PLACED IN THE "OFF" POSITION. ASSEMBLY INSTRUCTIONS HANDLE, SWITCH BOX AND CORD I. Place Lower handle tube (Fig. i) into handle tube socket "A" (Fig. 2). Fasten using bolt "B" and internally threaded nut "C" (Fig. 3) provided B_ _]_C in the hardware package. LOWER If the handle tube is difficult to assemble HANDLE (tight), insert blade of screwdriver into sl.ot TUBE (Fig. 4) at rear of handle tu
ملخص المحتوى في الصفحة رقم 5
DISPENSING SYSTEM MUST BE THOROUGHLY CLEANED IMMEDIATELY AFTER EACH USE. DO NOT STORE LIQUID IN DISPENSER. Remove dispenser from unit and empty. Rinse A-_.. thoroughly with warm water. The dispensing D D-... system must be flushed immediately after use. Partially fit[ dispenser with warm water, mount FIG. 11 on unit an then dispense at[ the water into a receptacle placed under the unit, ELECTRIC CORD PLUG SHOULD ALWAYS BE DISCONNECTED FROM THE ELECTRICAL OUTLET FIG. 10 FIG. t2 BEFORE ATTACHING,
ملخص المحتوى في الصفحة رقم 6
OPERATION (VINYL, LINOLEUM, ASPHALT TILE AND NO WAX FLOOR) INSTRUCTIONS I. SCRUBBING (FLOOR SRIPPING AND CLEANING) DISCONNECT CORD FROM ELECTRICAL OUTLET DO NOT USE MACHINE TO SCRUB WOOD FLOORS. Be sure to consult floor manufacturer for proper maintenance. Attach scrubbing brushes (for scrubbing floors Never use water-based products on wood floors. with an irregular surface) or nylon scrubbing pads (for scrubbing floors with a smooth Only use solvent based product on wood floors. surface). !, CL
ملخص المحتوى في الصفحة رقم 7
V. PERIODIC MAINTENANCE AVOID SOAKING. Mildewing or discolorations may occur. Sweep, dust or vacuum floor regularly. Continue to shampoo until the foam disappears, Buff floors as needed, following the directions then proceed to another area. above. Do not apply pressure. Light contact with the To remove scuff marks on heavy traffic areas, rug is sufficient for thorough cleaning. follow the polishing directions above. When shampooing a large area, the container Polishing and buffing floors often
ملخص المحتوى في الصفحة رقم 8
MODEL 680 84973 • EXTERNAL/€_CHINE PARTS 13 33 1 35 12 10 11 9 8 6 _I 6A 37C 16B 41 42 4 45 26 U
ملخص المحتوى في الصفحة رقم 9
MODEL 680 84973 . EXTERNAL/VLACHINE PARTS KEY PART NO. PART NAME KEY PART NO. PART NAME 47 53471 130947 Handle I FeLt Buffing Pad (2 req.) 48 130141 2 052696 Pad Retainer (2 req,) Upper Handle Tube 3 052710 Lower Handle Tube 48 450268 Pad Retainer 4 Pc. (Hardware Pks.) 49 240244 4 010536 Spring Yoke Torsion (1 req.) SeLfTapping Screw 6-20 x 3/4 (2 req,) 50 491899 5 130950 Switch box Motor AssembLy 3 speed 6 010154 51 461717 RepLacement Gear and Grease L Self Tapping Screw 6-20 x 5/16 52 461718 7
ملخص المحتوى في الصفحة رقم 10
MODEL 680 84973 EXTERNAL/v_ACHINE PARTS 7A O_ 64__ 75 __.L. 71 72 73 74 62B _70 63 _------- 76 6\ 84 _77 86 80 85 87 96E 96E 96C 96B
ملخص المحتوى في الصفحة رقم 11
MODEL.680 84973 • INTERNAL MACHINE PARTS KEY PART NO. PART NAME KEY PART NO. PART NAME 98 010154 60 131418 Motor Cover SeLfTapping Screw 6 x 5116 (2 req.) 99 010066 61 Self Tapping Screw 6 x 718 (1 reqo) 011483 Self Tapping Screw 101 251063 Push Plate 0.005" 62 280324 Brush Holder Assy 102 462069 62 A 460104 Brush Grease (2 reqo) 62 B 460590 Holder Assy 63 280263 Armature 64 011489 Self Tapping Screw &18 x 1/2 (4 req.) 65 054244 Field Support (2 req.) 67 280267 Field 3 Speed 67 A 081832 Field Sl
ملخص المحتوى في الصفحة رقم 12
m c -s ] Model No. I TheServiceSideof Sears.'_ 680.84973 For the repair or replacement parts you need Cat{ 7 am- 7pm, 7 days a week t -800-366-PART (t-800-366-7278) For in-home major brand repair service Cat[ 24 hours a day, 7 days a week 1-800-4-MY-HOME sM (I -800-469"4663) For the location of a Sears Parts and Service Center in your area Cat[ 24 hours a day, 7 days a week 1-800-488-1222 (1-800-469-4663) For more information on purchasing a Sears Maintenance Agreement or to inquire about an exi
