ملخص المحتوى في الصفحة رقم 1
T4261 T4261
Please keep this instruction sheet for future reference, Please keep this instruction sheet for future reference,
as it contains important information. as it contains important information.
R Requires three “AA” (LR6) alkaline batteries (not included) for operation. equires three “AA” (LR6) alkaline batteries (not included) for operation.
Adult assembly is required. Adult assembly is required.
T To ool required for assembly: Phillips screwdriver (not included). ol required for as
ملخص المحتوى في الصفحة رقم 2
Assembled Parts Assembled Parts CAUTION This package contains small parts in its unassembled state. Adult assembly is required. Upper Wall Lower Wall 2 Bases 8 Ramps Ramp Ramp Top Ramp 2 Balconies Car Lift Elevator (Labeled 1) (Labeled 2) (Labeled 3) #8 x ⅝ ” Screw – 7 Shown Actual Size The screw is shown actual size. Tighten or loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. T426
ملخص المحتوى في الصفحة رقم 3
Battery Installation Battery Safety Information In exceptional circumstances, batteries may leak fluids that can 1,5V x 3 cause a chemical burn injury or ruin your product. To avoid “AA” (LR6) battery leakage: • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). • Insert batteries as indicated inside the battery compartment. • Remove batteries during long periods of non-use. Always remove exhausted batteries f
ملخص المحتوى في الصفحة رقم 4
Consumer Information FCC Statement (United States Only) CONSUMER ASSISTANCE This equipment has been tested and found to comply with the 1-800-432-5437 (US & Canada) limits for a Class B digital device, pursuant to Part 15 of the 1300 135 312 (Australia) FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accorda
ملخص المحتوى في الصفحة رقم 5
Assembly Walls 1 • Fit the upper and lower walls together, as shown. Bases 3 • Place the bases on a flat surface, as shown. • Fit the wall assembly into each base and push to “snap” in place. Hint: The wall is designed to fit the bases one way. If it does not seem to fit, turn or switch one or both bases around and try again! Blue Dots T Top View op View 4 Screws 2 Ramp Labeled 2 • Insert four screws into the holes in the wall assembly and tighten. 4 • Locate the ramp labeled with a 2. • Fit
ملخص المحتوى في الصفحة رقم 6
Assembly Green Dots Ramps Labeled 1 T Top View op View Ramp Labeled 3 BACK FRONT 5 7 • Locate the ramp labeled 3. • Carefully turn the assembly around. • Fit the ends of the ramp into the slots in the wall and base, • Fit the ends of the three ramps labeled 1 into the slots in the wall, as shown. as shown. Hint: The tab at the top of the ramp has a green dot on it. Match • While holding each ramp in place, push the ramps on both sides this dot to the slot with the green dot. of the wall to
ملخص المحتوى في الصفحة رقم 7
Assembly Elevator Car Lift 9 • Fit the tabs on the car lift into the slots on the wall, as shown. 11 • Slide the elevator onto the end of the wall assembly, as shown. 3 Screws Top Ramp Balconies 10 • Fit the balconies into the slots in the wall assembly, as shown. Hint: The balconies are designed to fit one way. If a balcony does not seem to fit, turn it over and try again! • Push to "snap" each balcony in place. 12 • Fit the top ramp onto the assembly. • Insert three screws into the holes in
ملخص المحتوى في الصفحة رقم 8
Spiral Speed Action! • Slide the cars down the ramps for spiral speed action! • Lower the sign for stop lights and fun sounds! • Lift and lower the gas hose for car sounds. • Slide the power switch on the bottom of the toy ON . P Power Switch ower Switch When you are finished playing with this toy, slide the power switch OFF . 8
