ملخص المحتوى في الصفحة رقم 1
WARNINGS
WARNING
To prevent serious injury and/or falls:
SOUNDS 'N LIGHTS DELUXE
• Never use on any elevated surface.
• Never use as a carrier or lift while
SOOTHING BOUNCER
child is seated.
Model Number: 79008 • Always use the restraint system.
• Never leave child unattended.
Please save these instructions for future reference.
Tool needed for adult assembly:
• Never use as a car seat.
Phillips screwdriver (not included).
• Never use with a child able to sit
Requires one, size “D” (LR20) al
ملخص المحتوى في الصفحة رقم 2
PARTS ASSEMBLY CAUTION Toy Bar 2 Paddles This package contains small parts. Adult assembly is required. Red 1 Right Base Marks 2 Flowers Wire Butterfly Base Connector Pad Seatback Left Base Wire Wire Footrest Wire • Place the base connector on a flat surface as shown. • Position the left and right base wires as shown. Note the locations of the red marks on the left and right base wire. • Fit the left base wire into the base connector. Right Base • Fit the right base wire into the base connector.
ملخص المحتوى في الصفحة رقم 3
ASSEMBLY ASSEMBLY Base Wire Red Pull Up Mark Footrest Red Mark 4 2 Wire Base Wire Soothing Unit Plastic Cover • Position the footrest wire so that the soothing unit is upright. • While flexing the base wires toward each other, hook the footrest wire onto the ends of the base wires. • Push the footrest wire down completely, below the red marks on the base wires. Seat Back Protruding Side Wire 3 • Fit the nut (so that the protruding side is Toy Bar Socket outward) into the hexagonal opening on
ملخص المحتوى في الصفحة رقم 4
ASSEMBLY ASSEMBLY 6 5 Pad C A Plastic Plastic Cover Cover B Seat Back Elastic Elastic Wire Strap Strap Slot Restraint Belt Peg • Wrap the elastic straps on the pad B flaps around the outside of each Plastic Cover plastic cover. • Position the pad with the ruffle upright. • Hook the elastic straps to the peg on • Fit the upper pocket on the back Elastic the inside of each plastic cover. of the pad onto the seat back wire . A Strap • Fit the restraint belts through the slots in B the pad
ملخص المحتوى في الصفحة رقم 5
ASSEMBLY BATTERY INSTALLATION Toy Bar Wire 7 1.5V – + “D” (LR20) Paddle Paddle SHOWN ACTUAL SIZE Plugs Battery Compartment Door Flowers Sockets 8 Butterfly Soothing Unit • Lift the footrest wire. Remove the pad from the footrest wire. • Insert a coin into the battery compartment door and pry the battery compartment door off. • Insert one, size “D” (LR20) alkaline battery, as indicated inside the battery compartment. Be sure to place the battery on top of the ribbon. • Fit the toy bar plugs i
ملخص المحتوى في الصفحة رقم 6
BATTERY INSTALLATION SET-UP & USE 1.5V x 3 – “AA” (LR6) + WARNING SHOWN ACTUAL SIZE To prevent serious injury and/or falls: • Never use on any elevated surface. • Never use as a carrier or lift while child is seated. • Always use the restraint system. • Never leave child unattended. • Never use with a child able to sit up unassisted. Toy Bar • Locate the battery compartment door on the back side of the toy bar. • Loosen the screw in the battery compartment door with a Phillips screwdriver 1 an
ملخص المحتوى في الصفحة رقم 7
SET-UP & USE SET-UP & USE Anchored End Anchored End Lift for Upright 2 3 B Lower for B Recline Buckle Buckle Free End Free End Press Tighten Loosen To tighten the restraint: • Feed the anchored end of the restraint strap up through the buckle to form a loop . Press B • Pull the free end of the restraint strap . • Repeat this procedure to tighten the other restraint strap. To loosen the restraint: Button • Feed the free end of the restraint strap up through the buckle to form a loop
ملخص المحتوى في الصفحة رقم 8
SET-UP & USE CARE The pad is machine washable. Wash the pad separately in cold water on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly. The frame, toy bar, 4 mirror, paddles, butterfly and flowers may be wiped clean using a mild cleaning solution and a damp cloth. Do not immerse the soothing unit or toy bar. Soothing Vibrations To remove the pad: • Make sure your child is properly secured in the seat. • Remove the toy bar. • Slide the ON/OFF swit
