ملخص المحتوى في الصفحة رقم 1
TM
Please read this manual and save it with your original sales receipt.
Tools needed for assembly: Phillips Screwdriver,
Adjustable Wrench (or Pliers) and Safety Scissors (all not included).
®
Use only with a Power Wheels 12 Volt Lead Acid Rechargeable Battery
®
and Power Wheels 12 Volt Charger with Type 12V Connector
(both included). Requires four "C" (LR14) alkaline batteries for
FM Radio operation (batteries not included).
Product features may vary from the picture above.
Owner's Manual
ملخص المحتوى في الصفحة رقم 2
A T TABLE OF CONTENTS ABLE OF CONTENTS A Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 B Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 C Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 3
WARNINGS AND CAUTIONS B ELECTRICAL HAZARD WARNING • Battery can fall out and injure a child if vehicle tips over. Always use battery retainer. • PREVENT FIRE - Never modify the electrical system. Alterations could cause a fire resulting in serious injury and could also ruin the electrical system. - Use of the wrong type battery or charger could cause a fire or explosion resulting in serious injury. ® ® - Use of Power Wheels components in products other than Power Wheels vehicles could
ملخص المحتوى في الصفحة رقم 4
C PARTS • If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded. • Metal parts have been coated with a lubricant to protect them during shipment. Wipe all metal parts with a paper towel to remove any excess lubricant. Windshield Vehicle Hood Sport Bar
ملخص المحتوى في الصفحة رقم 5
A TABLE OF CONTENTS PARTS C #8 x 1" Screw – 4 12 Volt Battery 12 Volt Charger 5 #8-32 x 1 /8" Screw – 2 Taillight Lens Set 3 #10 x /4" Screw – 23 Taillight Housing Set 5 1 /32"x 1 /2" Pin – 1 Lens Guard - 2 Headlight Lens - 2 3 #8 Acorn Lock Nut – 2 #8 x /4" Screw – 1 Light Cover – 4 Hood Latch – 2 #8 x 3" Screw – 2 Key Assembly Steering Column Cap For your convenience, we included extra fasteners! Note: Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten the screws
ملخص المحتوى في الصفحة رقم 6
D A TABLE OF CONTENTS PARTS PICTURE Note: Some parts shown are assembled on both sides of the vehicle. 23 15 27 21 14 19 17 14 26 22 6 11 9 8 7 18 10 12 4 3 13 8 3 20 24 1 25 23 16 2 5 28 Parts Not Shown 1 Vehicle 11 Dash 21 Sport Bar 3 2 Steering Column 12 Headlight Lens - 2 22 Sport Bar Support - 2 #8 x 1" Screw - 4 #8 x /4" Screw - 1 3 3 Hood Latch - 2 13 Lens Guard - 2 23 Light Cover - 4 #10 x / " Screw - 23 #8 Acorn Lock Nut - 2 4 4 12 Volt Battery 14 Short Seat Belt Strap - 224 Door -
ملخص المحتوى في الصفحة رقم 7
BATTERY CHARGING E ELECTRICAL HAZARD WARNING CAUTION • Battery can fall out and injure a child Use the charger in dry locations only. if vehicle tips over. Always use battery retainer. About Thermal Fuses • PREVENT FIRE Your Power Wheels 12 volt battery is equipped with a built-in - Never modify the electrical system. thermal fuse. The thermal fuse is a self-resetting safety device Alterations could cause a fire resulting which automatically “trips” and shuts down operation of the vehicl
ملخص المحتوى في الصفحة رقم 8
E BATTERY CHARGING F F ASSEMBLY WARNING Children can be harmed by small parts, sharp edges and sharp points in the vehicle's unassembled state, or by electrical items. B Care should be taken in unpacking and assembly of the vehicle. Children should not Battery handle parts, including the battery, or help in assembly of the vehicle. A Dash Charger Connector A • Plug the charger connector into the battery . B • Plug the charger into a standard wall outlet . Notes: Motor Harness - Use
ملخص المحتوى في الصفحة رقم 9
ASSEMBLY F 17 9 9 Hole 6 Steering Column 7 4 BOTTOM VIEW DASH VIEW 2 • Wipe the steering column with a paper towel to remove any excess lubricant. • Turn the vehicle on its side. • Before applying the labels, wipe the surface of the vehicle with • Insert the straight end of the steering column up through the a clean, dry cloth to remove any dust or oils. hole in the vehicle frame and the vehicle floor and out through • Place the labels exactly as shown in the illustration. the hole in the
ملخص المحتوى في الصفحة رقم 10
F ASSEMBLY 5 1 / " x 1 / " Pin 32 2 End of End of Steering Steering Steering Column Column Cap Column Steering Rod Hole 6 5 1 • Insert the / " x 1 / " pin through the hole in the end of the 32 2 BOTTOM VIEW 8 steering column. • Lower the steering column so that the pin fits inside the center • Turn the vehicle on its side. of the steering wheel. • Insert the end of the steering column through the hole in the steering rod. • Fit the steering column cap onto the end of the steering column
ملخص المحتوى في الصفحة رقم 11
ASSEMBLY F Lens Guard Wide Tab Hood Latch Slot Lens Lens Wide Notch Lens Guard Hood Latch 10 12 Slot • Fit the wide notch in the side of a headlight lens under the • Insert a hood latch into one of the slots in the front end of wide tab on a lens guard. the vehicle. 1 • Press firmly on the inside of the headlight lens to snap it into • Twist the base of the hood latch /4 turn to secure it in the lens guard. the vehicle. • Repeat this procedure to assemble the other headlight lens to • Re
ملخص المحتوى في الصفحة رقم 12
F ASSEMBLY Spacers Windshield A Wipers Large Large Tab Tab Large Slots Grille 14 B #8 x 3" Screws 16 • Position the windshield so that the molded detail on the wipers faces the front end of the vehicle. • Fit two spacers between the grille and the back of the brush • Insert and “snap” the two large tabs on the windshield into A guard, as shown . the large slots in the dash. • Insert two #8 x 3" screws through the inside of the headlight, the • Pull up on the windshield to be sure it is sec
ملخص المحتوى في الصفحة رقم 13
ASSEMBLY F Seat Short Seat Belt Strap T-Loop (Pull through slot) Seat Back Tabs Tabs Fastener End T-Loops PUSH B HERE C Slot Slot Seat A Slot 18 SIDE VIEW • Turn the seat upside down. 20 • Insert the fastener end of a short seat belt strap through the slot near the outer edge of the seat. Make sure the side of the • With the seat at an angle, insert the tabs on the front edge of A seat belt with the fastener faces the outer edge of the seat. the seat into the slots in the foot-well wall .
ملخص المحتوى في الصفحة رقم 14
F ASSEMBLY Sport Bar Sport Bar Support PUSH HERE Side Fender PULL HERE Supports SIDE VIEW 24 • Fit the sport bar assembly into the holes in the top side of the vehicle. • Push down firmly on a sport bar support while pulling up on 22 the side fender to fit the sport bar into the vehicle. • Repeat this procedure on the other side of the vehicle. • Fit a support to one side of the sport bar. 5 " • Insert a #8- 32 x 1 /8 screw through the support, the sport bar and out through the support. •
ملخص المحتوى في الصفحة رقم 15
ASSEMBLY F Taillight Housing Door Taillight Lens #8 x 1" Screws BACK VIEW 26 • Turn the vehicle upright. • Using safety scissors, remove the taillight lenses and the taillight housings from the plastic connectors. Dispose of the plastic connectors. • Face the rear of the vehicle. SIDE VIEW • Fit a taillight lens inside a taillight housing. 28 • Position the taillight housing with lens against the vehicle with the screw holes aligned, as shown. • Fit a door into the groove on the side of the
ملخص المحتوى في الصفحة رقم 16
F ASSEMBLY DECORATION G • Wash your hands before applying the labels. • Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils. • Place the labels exactly as shown in the illustrations. Loosen These • For best results, avoid repositioning a label once it has been Screws applied to the vehicle. • After applying a label, rub the label firmly with a clean, dry cloth to make sure the label is adhered to your vehicle. Start at the center o
ملخص المحتوى في الصفحة رقم 17
DECORATION G 16 16 3 8 1 18 11 FRONT LEFT SIDE 2 12 13 8 18 16 16 11 3 FRONT RIGHT SIDE L7820pr-0920 L7820pr-0920 17
ملخص المحتوى في الصفحة رقم 18
H BATTERY INSTALLATION ® IMPORTANT! Use only a Power Wheels 12 volt battery. Use of any other battery will damage your vehicle. Make sure that you charge the battery for at least 18 hours using the enclosed ® Power Wheels 12 volt charger before operating your vehicle Motor Harness for the first time. Charge the battery for at least 14 hours after Connector each use of the vehicle. Never charge the battery longer than 30 hours. Failure to follow these instructions may damage your batter
ملخص المحتوى في الصفحة رقم 19
BATTERY CARE AND DISPOSAL I Care Disposal If a battery leak develops, avoid contact with the leaking acid ® • Your Power Wheels battery is a non-spillable, sealed lead- and place the damaged battery in a plastic bag. See information acid battery. They must be recycled or disposed of in an below for proper disposal. environmentally sound manner. If acid comes in contact with skin or eyes, flush with cool water • Do not dispose of a lead-acid battery in a fire. The battery may for at least 15
ملخص المحتوى في الصفحة رقم 20
J SAFE DRIVING RULES Teach Safety Rules to Children RIDING HAZARD While children can quickly develop the skill necessary to drive this vehicle, it is important to remember that their judgment skills WARNING are still very immature. Unsupervised driving by children can lead to serious injury. Before children use this vehicle, an adult should carefully evaluate the driving area as well as the children’s • Prevent Injuries and Deaths skill level and ability to drive this vehicle safely. Child
