ملخص المحتوى في الصفحة رقم 1
SECURITY SYSTEM
UPGRADE
INSTALLATION
FORESTER
INSTRUCTIONS
P/N: H7110FS400
NOTE: This system requires prior installation of Keyless Entry
System. If installing both systems at the same time, install the
Keyless Entry System first.
Kit Contents:
1 Security Control Module w/Integral Bracket
1 Starter Interrupt Relay w/Integral Bracket
1 Extension Harness 1m (3 ft.)
1 M6 Nut
1 Wire tie
2 Window Decals
1 Installation Manual
Tools Required:
#1 Flat-tip Screwdriver
#2 Phillips Head Screwdriver (short)
ملخص المحتوى في الصفحة رقم 2
A. Pre-Installation Notes 1. Vehicle Preparation a. Lower the driver’s side window to avoid inadvertently locking the keys in the vehicle dur- ing installation. b. Disconnect negative battery terminal to prevent accidental shorting of any power circuits. 2. System Preparation Remove the security module from the package and inspect for any physical damage. 3. Shock Sensor Adjustment The shock sensor adjustment knob is recessed inside the unit and is covered by a protective seal. This adjustment i
ملخص المحتوى في الصفحة رقم 3
5. Remove and retain for reinstallation, the black M8 bolt indicated by the arrow “A” in Figure 4. Loosen the M8 bolt indicated by the arrow “B.” Figure 4 6. Route the male connector of the extension harness under the center console from the driver’s seat side. See Figure 5. 7. Insert the male connector of the extension harness into the security module 18-pin connector. Figure 5 8. Install the security module onto the bolt indicated by the arrow “B” which was loosened in step 5, then tighten the
ملخص المحتوى في الصفحة رقم 4
9. Remove one plastic screw and two metal screws indicated by the arrows in Figure 7, then remove the lower dash panel by pulling the upper side of the lower dash panel toward you. 10.Disconnect the four harnesses (two white housings, one brown housing and one black housing) on the lower dash panel. Then, completely remove the lower dash panel. Figure 7 NOTE: To detach the black housing, insert a slot- ted screwdriver as shown in Figure 8 and lift up the black housing. The black hous- ing can be
ملخص المحتوى في الصفحة رقم 5
12.As shown in Figure 10, insert the female connector Security module Wire tie harness of the extension harness into the security module 18- pin (white housing) connector. Push the extension harness into under the center con- sole. Take care not to damage the extension harness. 13.Make sure that the harness is not being pintched or is not touching any sharp sheet metal. Then, securely fix the harness to the other vehicle near by harnesses using the supplied wire tie. Figure 10 C. Starter Interru
ملخص المحتوى في الصفحة رقم 6
D. Prior to System Test 1. Reconnect negative battery terminal. E. System Test 1. Exit the vehicle and close all doors. 2. Depress the LOCK/ARM button on the remote and the following should be observed: a. All vehicle doors will lock. b. The parking lights will flash once and the horn will chirp once. c. Status indicator (LED) will begin to flash 1x per 2 seconds. 3. Wait 5 seconds then depress the UNLOCK/DISARM button on the remote and the following should be observed: a. The driver’s door will
ملخص المحتوى في الصفحة رقم 7
5. Depress the UNLOCK/DISARM button and the driver’s door should unlock. 6. Open the driver’s door and then depress and hold the UNLOCK/DISARM on the remote for more than 2 seconds and the following should be observed: a. The status indicator (LED) will stop flashing indicating that the alarm is now out of valet mode and has returned to normal operation. b. All the doors will unlock. G. Shock Sensor Test 1. Lower the driver’s side window then close all doors. 2. Depress the LOCK/ARM button on th
ملخص المحتوى في الصفحة رقم 8
I. Shock Sensor Adjustment-ONLY IF REQUIRED The factory has preset the sensitivity of the shock sensor at the time of manufacture. Under normal circumstances the sensitivity should not require any adjustment and should be left untouched. However, in the unlikely event that adjustment is required, please follow the steps outlined below. 1. Carefully remove the seal covering the shock sensor adjustment hole on the top of the security module. 2. Using a #0 flat-tip screwdriver, CAREFULLY AND GENTLY
