Crimestopper Security Products CS-2000DPII TW2 دليل المستخدم

دليل المستخدم للجهاز Crimestopper Security Products CS-2000DPII TW2

جهاز: Crimestopper Security Products CS-2000DPII TW2
فئة: إنذار السيارات
الصانع: Crimestopper Security Products
مقاس: 0.32 MB
مضاف: 8/19/2013
عدد الصفحات: 24
اطبع الدليل

تحميل

كيفية استخدام هذا الموقع؟

هدفنا هو أن نوفر لك وصولاً سريعًا إلى محتوى دليل المستخدم الخاص بـ Crimestopper Security Products CS-2000DPII TW2. باستخدام المعاينة عبر الإنترنت ، يمكنك عرض المحتويات بسرعة والانتقال إلى الصفحة حيث ستجد الحل لمشكلتك مع Crimestopper Security Products CS-2000DPII TW2.

لراحتك

إذا لم يكن البحث في دليل المستخدم Crimestopper Security Products CS-2000DPII TW2 مباشرة على موقع الويب هذا مناسبًا لك ، فهناك حلان محتملان:

  • عرض ملء الشاشة - لعرض دليل المستخدم بسهولة (بدون تنزيله على جهاز الكمبيوتر الخاص بك) ، يمكنك استخدام وضع العرض بملء الشاشة. لبدء مشاهدة دليل المستخدم Crimestopper Security Products CS-2000DPII TW2 بملء الشاشة ، استخدم الزر تكبير الشاشة.
  • التنزيل على جهاز الكمبيوتر الخاص بك - يمكنك أيضًا تنزيل دليل المستخدم Crimestopper Security Products CS-2000DPII TW2 على جهاز الكمبيوتر لديك والاحتفاظ به في ملفاتك. ومع ذلك ، إذا كنت لا تريد أن تشغل مساحة كبيرة على القرص الخاص بك ، فيمكنك دائمًا تنزيله في المستقبل من ManualsBase.
Crimestopper Security Products CS-2000DPII TW2 دليل الاستخدام - Online PDF
Advertisement
« Page 1 of 24 »
Advertisement
النسخة المطبوعة

يفضل العديد من الأشخاص قراءة المستندات ليس على الشاشة ، ولكن في النسخة المطبوعة. تم أيضًا توفير خيار طباعة الدليل ، ويمكنك استخدامه بالنقر فوق الارتباط أعلاه - اطبع الدليل. لا يتعين عليك طباعة الدليل بالكامل Crimestopper Security Products CS-2000DPII TW2 ولكن الصفحات المحددة فقط. ورق.

الملخصات

ستجد أدناه معاينات لمحتوى أدلة المستخدم المقدمة في الصفحات التالية لـ Crimestopper Security Products CS-2000DPII TW2. إذا كنت ترغب في عرض محتوى الصفحات الموجودة في الصفحات التالية من الدليل بسرعة ، فيمكنك استخدامها.

ملخصات المحتويات
ملخص المحتوى في الصفحة رقم 1







CS-2000DPII TW2
With 2-Way Data Port Technology
2-WAY REMOTE CONTROL ALARM SYSTEM
INSTALLATION & OPERATING INSTRUCTIONS


INTRODUCTION

CONGRATULATIONS on your choice of an “On-Guard” Remote Alarm System by Crimestopper Security
Products Inc. This booklet contains the information necessary for installing, using, and maintaining your alarm
system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the
Tech Support number bel

ملخص المحتوى في الصفحة رقم 2

TABLE OF CONTENTS Installation Cautions & Warnings..…….……………………………….……………………………………….……2 Control Module & Component Mounting ……………...……………………..……………………….…….…..…..3 Wiring (LED, PROGRAM BUTTON AND SHOCK SENSOR page 5-6)…………………..………….….…..….3-6 Power Door Lock Wiring……………………………………………………….………………………….…...….…6-7 Data Port Diagram ………………………………………………………………………………………………….……8 nd Transmitter Programming (2 Vehicle programming)..……………………………………………….…….....…9 Option Programming………………………………

ملخص المحتوى في الصفحة رقم 3

CONTROL MODULE & COMPONENT MOUNTING DO NOT Mount the control module in the engine compartment or where the wiring harness can become entangled with moving parts such as brake/gas/clutch pedals, or the steering column! The alarm control module should be mounted in a concealed location. The Placement of the module will affect the distance from which the remote transmitter can control the unit. The antenna wire should be routed away from any metal if possible. Do not alter the length of

ملخص المحتوى في الصفحة رقم 4

WIRING BLACK WIRE: SYSTEM CHASSIS GROUND The Black wire MUST be connected to the CHASSIS METAL of the vehicle. Scrape away any paint or debris from the connection point and use a star washer to ensure a good connection. Keep the ground wire short. YELLOW WIRE: IGNITION SWITCHED “ON” AND “START” +12 VOLTS Connect to an IGNITION wire (or fuse in the fuse box) that shows +12 Volts when the key is in both “On” and “Start” (WHEN CRANKING) positions. GRAY WIRE: (-) NEGATIVE AUX REMOTE O

ملخص المحتوى في الصفحة رقم 5

WIRING BLUE/WHITE WIRE: NOT USED BROWN WIRE: (+) SIREN OUTPUT (3 Amp Max.) Connect to RED siren wire from the Siren in the engine compartment. WHITE WIRE: +12V FLASHING PARKING LIGHT OUTPUT Connect to the switched parking light wire at back of light switch. If this is not possible, connect directly to one of the parking lights at the front of the vehicle. European vehicles require separate right and left circuits. Use a dual relay or 2 diodes to separate the output signal. RED

ملخص المحتوى في الصفحة رقم 6

WIRING: SHOCK SENSOR 4 PIN SENSOR PLUG/HARNESS (BLUE): White Wire: Negative Trigger GREEN LED (Pre-Warn) SENSITIVITY Blue Wire: Negative Warn-away RED LED (Trigger) ADJUSTMENT Black Wire: Sensor Ground Red Wire Sensor Power SENSOR ADJUSTMENT SHOCK SENSOR: The sensor supplied Clockwise = Higher Sensitivity Counter Clockwise = Lower Sensitivity with this system does not require any 1) Start adjustment by turning sensitivty at additional wiring. Simply mount the minimum. sensor

ملخص المحتوى في الصفحة رقم 7

POWER DOOR LOCK WIRING NEGATIVE TRIGGER DOORLOCK WIRING POSITIVE TRIGGER DOORLOCK WIRING GREEN GREEN FUSED RED RED +12V BLUE + BLUE 86 85 86 85 87 87 30 87A 30 87A FACTORY FACTORY L L POWER POWER LOCKING LOCKING UL UL RELAYS RELAYS REVERSE POLARITY DOOR LOCK WIRING AFTERMARKET MOTOR/DOOR LOCK WIRING GREEN GREEN FUSED FUSED RED RED +12V +12V BLUE + BLUE + 85 86 85 86 85 86 85 86 87 87 87 87 87A 30 87A 30 87A 30 87A 30 MASTER SWITCH + CUT L UL CUT 7

ملخص المحتوى في الصفحة رقم 8

DATA PORT DIAGRAM Data bus Systems: Data Controlled door locks, Factory Security and many accessories This unit includes DP Technology it will allow you to plug our modules which operate Data control Door locks, accessories, and Bypass Factory security systems directly into the unit by via Data Port. The module cable plugs directly to the Data port on the side of the unit. Please refer to Databus module manual for detail instructions. Option #16 controls the Data Port Protocol for 1

ملخص المحتوى في الصفحة رقم 9

TRANSMITTER PROGRAMMING NOTE: All transmitters must be learned at the time of programming. This system can learn up to 4 remotes. 1. Turn key to the ON position and press program button 4 times. 2. After a short delay, the unit will flash the parking lights 4 times, Siren 4 times, Horn 4 times and status LED will be on solid. 3. Press the Button #1 (Lock) AND Button #2 (Unlock) together on the remote you wish to program. 4. You should get 2 light flashes, 2 siren chirps and 2 horn ho

ملخص المحتوى في الصفحة رقم 10

OPTION PROGRAMMING 1. Turn the Ignition ON and press the Override/Program button 5 times. 2. After a short delay, the parking lights will flash 5 times, Siren 5 times, Horn 5 times and status LED will be on solid. 3. Within the next few seconds, press the Override/Program button [again] the number of times that corresponds to the options chart below. Siren and/or optional horn should chirp for each press. 4. When you get to the desired option number, quickly press the appropriate button

ملخص المحتوى في الصفحة رقم 11

OPTION PROGRAMMING NOTE: Options can be instantly restored to Factory Default Values. To restore default values: Perform step #1 (See page 10), then press buttons (1+2) together. The siren and horn will chirp 4 times and lights will flash 4 times. Turn OFF Ignition. All programming options will be restored to * Default * values (See page 10). 1. HORN CHIRPS / PULSES This option controls the system’s Factory Vehicle Horn output. There are 3 selections: Button 1 (Lock) = Hor

ملخص المحتوى في الصفحة رقم 12

OPTION PROGRAMMING 6. ACTIVE RE-ARMING Active Re-arming allows the system to re-arm itself 30 seconds after disarmed with the transmitter if a door has not been opened. This is handy if the vehicle is accidentally disarmed (via the Transmitter in your pocket) without you knowing it. Note: Active re-arm is reset by dome light illumination. If you are using dome light illumination, active re-arm will not function. 7. DOUBLE UNLOCK PULSE With this feature enabled, the unit will sen

ملخص المحتوى في الصفحة رقم 13

OPTION PROGRAMMING Cont. 14. CARJACK FEATURES This option controls the unit’s Car Jack features. Enable or Disable Carjack (Turn ON or OFF) with this option. 15. Lock/Unlock or Arm/Disarm with Ignition ON This option allows you Arm and Disarm the system with the Ignition ON. This is used when there is a remote starter added to the system. The default is lock/unlock without arm and disarm while the ignition on. 16. Data Port Protocol: This option controls the Data Port Protocol for

ملخص المحتوى في الصفحة رقم 14

OPERATING INSTRUCTIONS (REMOTE OPERATIONS) ONE WAY SIDEKICK REMOTE: The transmitter supplied with the CS-2000DPII-TW2 system #2 UNLOCK has four buttons. The button configuration of the CS- 2000DPII-TW2 is Factory-set and unchangeable. See #1 FLASHLIGHT second vehicle operation for additional information on how LOCK VEHICLE #2 to use your remote to operate a second vehicle equipped #3 SLNT with a OnGuard system. #4 TRUNK SILENT ARM BUTTON FUNCTIONS (AUX #1) & DISARM BUTTON 1(Lock S

ملخص المحتوى في الصفحة رقم 15

OPERATION INSTRUCTIONS (TRANSCEIVER / PAGER-REMOTE) PAGER / REMOTE TRANSCEIVER: FIXED The hand-held remote transceiver is used to send and receive ANTENNA information from the vehicle. The Control Module transmits High #2 DISARM Frequency signals from the vehicle to your over long distances. #1 ARM UNLOCK Your range will vary depending on location, terrain, and local RF LOCK noise/interference. This system is not guaranteed to page you if you are behind concrete walls, undergrou

ملخص المحتوى في الصفحة رقم 16

OPERATION INSTRUCTIONS (LCD PANEL FUNCTIONS SHOWN) ST ARM DISARM DOOR OPEN (FLASH) PANIC (FLASH) 1 AUX. OUTPUT TRUNK CAR JACK POP (FLASH) (OR HOOD OPEN) VALET DATA TRANSLATE IGN TRIGGER (FLASH) WARN AWAY (FLASH) SHOCK SEN

ملخص المحتوى في الصفحة رقم 17

OPERATION INSTRUCTIONS ACTIVE ARMING To arm the alarm and lock the doors, press the #1 (Lock Symbol) button on the transmitter. You will hear a single siren chirp and the lights will flash once. The system will arm, the doors will lock and the starter will be disabled if these optional features are installed. The red LED in the vehicle will start flashing after 5 seconds. After a short delay to allow vehicle and electronics to stabilize the system will be completely armed. ALARM TRI

ملخص المحتوى في الصفحة رقم 18

OPERATING INSTRUCTIONS SELECTIVE SILENT ARM/DISARM THROUGH REMOTE CONTROL This system can be armed and disarmed without siren chirps on an “as needed” basis. Press and release Button #4 for arm/disarm without siren chirps. PROGRAMMABLE SILENT ARM/DISARM MODE (CHIRP DEFEAT) The system can be silently armed and disarmed as normal with Lock/Unlock Buttons, but no siren chirp. See alarm programming option (#8) to enable or disable this feature. EMERGENCY OVERRIDE / DISARM If you hav

ملخص المحتوى في الصفحة رقم 19

OPERATING INSTRUCTIONS PRIOR INTRUSION ALERT If the system was tripped in your absence, the dash LED will be flashing rapidly. When the system is disarmed you will hear 3 chirps (and 3 light flashes). Carefully inspect your vehicle to see if there is any damage or a theft has occurred. DOME LIGHT ILLUMINATION (OPTIONAL) This feature turns on the vehicles dome light upon disarm for 30 seconds or until the key is inserted and turned on. This will provide illuminated entry to your veh

ملخص المحتوى في الصفحة رقم 20

CARJACK PROTECTION FEATURES ACTIVE CARJACK This feature provides Active Carjack protection and must be enabled before use through Alarm programming option (14) See page 10. When the Ignition is on (vehicle is running), press and hold button #3 (AUX) for 3 seconds. Parking lights will flash TWICE to confirm the Carjack countdown sequence. LED begins to flash slowly. 90 Seconds later, the unit will begin a Carjack Cycle consisting of 20 seconds of pre-warning chirps turning into a full


أدلة المستخدم البديلة
# دليل الاستخدام فئة تحميل
1 Crimestopper Security Products CS-2000 دليل الاستخدام إنذار السيارات 32
2 Crimestopper Security Products CS-2003DC دليل الاستخدام إنذار السيارات 4
3 Crimestopper Security Products CS-2003DC SERIES II دليل الاستخدام إنذار السيارات 6
4 Crimestopper Security Products CS-2014FM دليل الاستخدام إنذار السيارات 7
5 Crimestopper Security Products CS-2000DP-TW2 دليل الاستخدام إنذار السيارات 6
6 Crimestopper Security Products CS-2008PC دليل الاستخدام إنذار السيارات 1
7 Crimestopper Security Products CS-2013FM دليل الاستخدام إنذار السيارات 1
8 Crimestopper Security Products CS-2016DP-FM دليل الاستخدام إنذار السيارات 4
9 Crimestopper Security Products CS-2001 دليل الاستخدام إنذار السيارات 1
10 Crimestopper Security Products CS-2100 دليل الاستخدام إنذار السيارات 12
11 Crimestopper Security Products CS-2205 دليل الاستخدام إنذار السيارات 3
12 Crimestopper Security Products CS-830RKE دليل الاستخدام إنذار السيارات 0
13 Crimestopper Security Products CS-8050 دليل الاستخدام إنذار السيارات 2
14 Crimestopper Security Products CS-845RKE دليل الاستخدام إنذار السيارات 7
15 Crimestopper Security Products CS-865RKE دليل الاستخدام إنذار السيارات 4
16 Philips 42HF7945D دليل الاستخدام إنذار السيارات 1
17 Aastra Telecom 600 دليل الاستخدام إنذار السيارات 0
18 Acumen CAT21 دليل الاستخدام إنذار السيارات 16
19 Alamo RX84 دليل الاستخدام إنذار السيارات 5
20 Samsung SPF-83H دليل الاستخدام إنذار السيارات 5