ملخص المحتوى في الصفحة رقم 1
CS-2013FM
2-Way FM Remote Start & Alarm System
CONGRATULATIONS! on your choice of a CS-2013FM 2-Way FM Paging Remote Alarm/Remote Starting System
by Crimestopper Security Products Inc. This booklet contains the information necessary for installing, using, and
maintaining your alarm system. If any questions arise, contact your installation dealer first, or Crimestopper
Security Products Inc. at the Tech Support number listed below. This system is designe
ملخص المحتوى في الصفحة رقم 2
TABLE OF CONTENTS Installation Cautions & Warnings…….………….…………………………...………………………………………………2-3 Suggested Component Mounting………….……...……………………………...…………………………….……………....3 Wiring Information……………………………….……………………………..……………………………...………….…….4- 7 Power Door Lock Wiring...………………………..…………………………………….……………………………..….……8- 9 Remote Start: Tach & Tach-less Programming……………………………………..……………………………….……10- 11 Option Programming……………………………….…………….………………………...………………….…………….11- 15 Option Reset Pr
ملخص المحتوى في الصفحة رقم 3
Prior Intrusion Diagnostics………………………….………………………………………………………...……….…..……22 Remote Start Operation……………….…………………………………………………………………………..….……..22- 23 Special LCD FM Remote-Pager Functions……….…………………………………………………………..………………24 INSTALLATION CAUTIONS & WARNINGS CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDOR shall not be responsible or liable in any way for accidents or damage resulting from the use of this equipment. This system is designed to be professionally installed in a vehicle
ملخص المحتوى في الصفحة رقم 4
SUGGESTED COMPONENT MOUNTING Control Module: Driver or Passenger side underdash, the unit should be placed as high as possible, not easily accessible by an intruder. Shock Sensor: Mount with wire ties to an under dash wire harness or fasten with screws to a panel. Siren: Under the hood to fender-well or other body surface with the open end facing downward. LED: In a visible location on the dashboard or console. Override/Program button: Hidden location, but accessible to
ملخص المحتوى في الصفحة رقم 5
Programmable Auxiliary Output Channel #2. BLACK/WHITE WIRE: (-) DOME LIGHT ILLUMINATION (Optional, Requires Relay) Connect to terminal 85 of relay. This wire turns the dome light on for 30 seconds upon disarming of the alarm. If the ignition is turned on or the alarm is re-armed, the dome light will turn off again. Connect this wire to terminal 85 of a relay. Connect terminal 86 to +12V Constant. Connect terminal 87 to +12V or ground depending on the type of Dome Light/Door Pin circui
ملخص المحتوى في الصفحة رقم 6
WHITE/BLACK WIRE: (-) HOOD/TRUNK TRIGGER (Mandatory For Hood Pin) Input trigger for a grounding hood or trunk pin switch and to inhibit remote start if the hood is open. Connect to existing hood and trunk pin switches that read ground when open. If no existing switches are available, install a new pin switch. Note: DO NOT mount new pin switches in water pathways. ORANGE WIRE: (-) NEGATIVE ARMED OUTPUT (STARTER DISABLE) Sends constant Ground output when system is armed. This output is u
ملخص المحتوى في الصفحة رقم 7
GREEN: (-) NEGATIVE LOCK Connect directly to negative lock/unlock systems. If vehicle uses RED: +12V For Relays positive door lock signals or reversing polarity type, then external BLUE: (-) NEGATIVE UNLOCK relays must be added. See Power Door Lock Wiring: Pages 8- 9. 4 PIN (WHITE) SENSOR PLUG: WHITE: NEGATIVE PRE-WARN BLACK: SENSOR GROUND BLUE: NEGATIVE TRIGGER RED: SENSOR POWER 3 PIN (BLUE) DATA PLUG ON RIGHT SIDE OF MODULE: Data port for 2-WAY FM Transceiver Box & Antenn
ملخص المحتوى في الصفحة رقم 8
12 GREEN (-) NEGATIVE DOOR TRIGGER INPUT 13 WHITE/BLACK (-) HOOD/TRUNK TRIGGER INPUT 14 ORANGE (-) ARMED OUTPUT (STARTER DISABLE) 15 VIOLET/WHITE (-) OEM FACTORY DISARM OUTPUT 16 WHITE/VIOLET (-) OEM FACTORY ARM OUTPUT 17 BROWN (+) SIREN POSITIVE OUTPUT 18 GRAY (-) NEG AUXILIARY CHANNEL OUTPUT #1 (TRUNK POP) 19 WHITE (+) 12V PARKING LIGHT OUTPUT 20 BROWN/WHITE (-) NEG HORN HONK OR NEG IGN OUTPUT POWER DOOR LOCK WIRING
ملخص المحتوى في الصفحة رقم 9
NEGATIVE TRIGGER DOORLOCK WIRING POSITIVE TRIGGER DOORLOCK WIRING GREEN GREEN FUSED RED RED +12V BLUE + BLUE 85 86 85 86 87 87 30 87A 30 87A FACTORY FACTORY L L POWER POWER LOCKING LOCKING UL UL RELAYS RELAYS REVERSE POLARITY DOOR LOCK WIRING AFTERMARKET DOOR LOCK WIRING GREEN GREEN FUSED FUSED RED RED +12V +12V BLUE + BLUE + 85 86 85 86 85 86 85 86 87 87 87 87 87A 30 87A 30 87A 30 87A 30 MASTER SWITCH + CUT L LOCK WIRE UL CUT UNLOCK WIRE SEPARATE DRIVER’S DOOR UNLOCK WIRING
ملخص المحتوى في الصفحة رقم 10
NEGATIVE TRIGGER DOOR LOCKS BLUE/WHITE GREEN RED BLUE DRIVER'S DOOR MOTOR 85 86 L L 87 UL UL 30 87A FACTORY LOCK RELAYS +12V + FUSED CUT UNLOCK WIRE WIRING FOR REVERSE POLARITY DOOR LOCKS BLUE/WHITE GREEN FUSED RED +12V BLUE + 85 86 85 86 MASTER 85 86 SWITCH 87 87 87 87A 30 87A 30 30 87A + L CUT UL CUT CUT LOCK WIRE UNLOCK WIRE REMOTE START:TACH & TACHLESS MODE
ملخص المحتوى في الصفحة رقم 11
The CS2013FM system includes both Tach and Tach-less modes for engine sensing & starter control. This system can be programmed for either mode, but it is set to Default in “Tachless Mode”. It will work for most vehicles in Tach-less mode. SMART SENSE TACH-LESS MODE: When the system is in “Smart Sense” Tachless mode, the module monitors the vehicle’s voltage, and RF noise level reference each time a remote start is performed. No Tach wire is required when using “Smart Sense” Tach-less
ملخص المحتوى في الصفحة رقم 12
LEARNING THE TACH (RPM) SIGNAL: 1. Have the Black/Gray Tach wire connected to your Tach source. 2. Start engine with key. 3. Within 10 seconds, press the valet/program button 5 times, the siren should chirp 3 times. 4. Push program button again (21) times, you should get a siren chirp for each button press. Be careful and DO NOT LOSE COUNT. This unit is now at option #21-Tach Learning. 5. Press the #1 Lock Button on remote transmitter. The unit will record and program your Tach source.
ملخص المحتوى في الصفحة رقم 13
1. Passive Arming Disabled* Enable 2. Active Re-Arm Disabled* Enable 3. Silent Arm/Disarm Chirps* No Chirps 4. Lock when IGN turns ON/ Enabled* Disabled Custom Custom Override mode Override Mode 5. Unlock when IGN turns OFF Enabled* Driver’s door only NO IGN Unlock 6. Double Unlock Pulse 1 Pulse* 2 Pulses 7. Door Lock Pulse: 1 or 3 sec. 1 Second* 3 Seconds 8. Passive Lock Disabled* Enable 9. Beach Mode (Remote-less Disarm) Disabled* Enable 10. Open Zone Warning 5 Seconds* OFF
ملخص المحتوى في الصفحة رقم 14
This option controls the Passive (Automatic) Arming feature and the Hands free mode. Button #1 = Passive Arming OFF. Button #2 = Enables Passive Arming. When Passive arming is enabled, arming will occur 30 Seconds after the ignition is turned off and the last door has been closed. 2. ACTIVE RE-ARMING This option controls the Active Re-arming feature. Button #1 = Active Re-arming OFF. Button #2 = Enables Active Re-arming. Active Re-arming allows the system to re-arm itself 30 seconds
ملخص المحتوى في الصفحة رقم 15
This option controls whether the doors will lock when Passive Arming occurs. Note: May increase the risk of locking keys in the vehicle. When selected ON, the alarm will lock the doors when passive arming. 9. REMOTE-LESS DISARM “BEACH MODE” (Note: this option also requires Passive arming/Passive locks) This option allows the system to be disarmed without the remote as long as the key is inserted and turned ON within 10 seconds. This feature only operates after the system has passively a
ملخص المحتوى في الصفحة رقم 16
18. REMOTE START ENGINE RUN TIME: Controls the amount of running time for remote start: 12 or 24 Minutes. 19. COLD START INTERVAL TIME Controls the time between remote engine starts when the “Cold Start” feature is activated: Every 1 or 2 hours. 20. TACH or TACHLESS MODE Controls whether the system operates in Tachless mode or Tach mode using Engine RPM. 21. TACH LEARNING / GAS / DIESEL ENGINE This option controls tach learning and engine type. There are 3 selections: Button #1 = S
ملخص المحتوى في الصفحة رقم 17
Custom override allows the user to set a specific number of button presses (2 to 15) required to perform an emergency override/disarm of the alarm system. This helps to defeat the common perception of a thief that if you turn the vehicle’s ignition on and press the valet button, most alarms will shut down. This feature increases the level of security of your alarm system, however MUST MEMORIZE how many button presses you have changed your system to use or the unit will not disarm!!! 1.
ملخص المحتوى في الصفحة رقم 18
ADDITIONAL TRANSCEIVER PROGRAMMING: 2-WAY FM REMOTE 1. Turn the ignition on, within 10 seconds press the override/program button 5 times. Siren will chirp 3 times indicating you are in feature programming mode. 2. Within the next 5 seconds, carefully press the override/program button 22 times. The siren will chirp once for each button press. Press Carefully and DO NOT LOSE COUNT. 3. Press Button #2 on the 1-Way remote. 4. Press Button #1 on the new 2-way FM remote, wait a second then
ملخص المحتوى في الصفحة رقم 19
OPERATION: (1-WAY REMOTE) 5-Button One-Way Remote Functions: BANK #1 (Directly Press Buttons) BUTTON 2 Button 1: Arm / Lock (Hold 4 seconds for Panic) BUTTON 1 Button 2: Disarm / Unlock Button 3: Aux #1 (Trunk Release) Button 4: Remote Start (Hold 2 sec.) BUTTON 5 Button 5: (Change to BANK #2) PANIC (ON SIDE) BUTTON 3 BANK #2 (Press Button 5 FIRST, then within 3 seconds Buttons 1-4) BUTTON 4 Button 1: Silent Arm (No Chirp) Button 2: Silent Disarm (No Chirp) Button 3
ملخص المحتوى في الصفحة رقم 20
ALARM OPERATION DISARMING: Press Button #1 (Lock Symbol) on the 2-Way remote. For the 1-Way remote Press Button #2 (Unlock Symbol) to disarm. The 2-Way remote will confirm with an “UNLOCK” icon on the LCD display and an audible signal. At the vehicle, the siren will chirp (2) times and the lights will flash (2) times. The red LED in the vehicle will turn off. (Doors will unlock and the interior dome light will turn on if these optional features are installed.) ONE-TIME SILENT ARM/
