ملخص المحتوى في الصفحة رقم 1
TM
World-Class Auto Security
Owner’s Manual
ملخص المحتوى في الصفحة رقم 2
Using Your XL1000 Security System 2-Button/3-Channel Remote Control The 2-button/3-channel remote control is a miniature radio transmitter with a range of up to 100 feet. Obstructions, interference or a weak battery will reduce the range. Your 2-button/3-channel remote control is the key to your security system. It is an ingenious user-friendly device that transmits three distinct and unique digital codes. Use it to arm or disarm the system, lock or unlock the doors, activate its panic feature o
ملخص المحتوى في الصفحة رقم 3
AutoLock/AutoUnlock For your safety and that of your passengers, the system automatically locks the doors when you turn on the ignition switch to start the engine and unlocks them once the ignition is turned off. If you prefer, you may turn off the AutoLock/AutoUnlock feature. See the User-Selectable Features section on pages 6-7. AutoArming™ If you forget to remotely arm, the system will arm itself automatically (“passively”) 30 seconds after the vehicle doors are closed. If you re-open any doo
ملخص المحتوى في الصفحة رقم 4
Tampering Warning Normally, the system immediately sounds its siren at the first inkling of an intru- sion attempt. However, you may set the system to issue a rapid five-chirp warning whenever the system detects tampering to the exterior of your vehicle. If there is any further tampering within the next 30 seconds, or if a door, the hood or trunk is opened at any time, your system will sound a continuous 125dB siren blast. To select the mode of your choice, see User-Selectable Features on pages
ملخص المحتوى في الصفحة رقم 5
Automatic Malfunction Bypass To provide the utmost protection even if a system component malfunctions, the system will automatically bypass the faulty point and arm all other triggers and sensors until you can have the system serviced by your local Authorized Dealer. Smart Prior Intrusion Attempt Alert When you remotely disarm, if you hear 3 chirps instead of the usual one chirp it means that a trigger or sensor was activated in your absence. When you enter the vehicle, the LED will blink severa
ملخص المحتوى في الصفحة رقم 6
AntiScan Car thieves use electronic scanners that rapidly transmit one remote control code after another to defeat ordinary alarms. AntiScan prevents scanners from disarming your system. How to Interpret the Chirps and Parking Light Flashes When you press the remote control buttons, the system will respond with chirps (unless you have the chirp muting feature turned on) and flashes the parking lights to indicate the system status. The meaning of these chirp/flash acknowledgments is as follows: N
ملخص المحتوى في الصفحة رقم 7
User-Selectable Features Your XL1000 vehicle security system allows you to set many of its features to your own personal preferences. We have made the programming procedures very simple: to make a change, you just flick the valet switch a few times. The system comes from the factory with all of its features pre-programmed as noted in the table below and on page 7. To change any of the settings, use the procedure noted. To restore the feature to its factory setting, just repeat the procedure: 1.
ملخص المحتوى في الصفحة رقم 8
# of Program Factory Secondary flicks & completion Feature setting action Result chirps confirmation Add a New Button I/channel 1 code of Remote to Press remote control button I 13 — 1 chirp new remote control has Channel 1 been memorized (arm/disarm) Add a New Remote to Button II/channel 2 code of Channel 2 Press remote control button II — 14 2 chirps new remote control (optional re- has been memorized mote accessory) Add a New Remote to Press remote control buttons I+II Button I+II/channel 3
