ملخص المحتوى في الصفحة رقم 1
ملخص المحتوى في الصفحة رقم 2
Stan dard Fea tures The fol low ing are stan dard fea tures of this sys tem. Some ve hi cles may re quire op tional par ts/wir ing and a few are in com pati ble with some fea tures. þ Lifetime warranty (see terms & conditions) þ Built-in parking light flasher þ Two remote controls þ Courtesy light(s) turn on when you disarm with the remote (requires optional relay) n 100’ range (300’ with optional ElectroLoop Antenna) n ACG 2™ Anti-CodeGrabbing protection þ Remote panic feature n Low remote cont
ملخص المحتوى في الصفحة رقم 3
Wel come to the world of high- technology ve hi cle se cu rity and con ven ience ongratulations on the purchase of your Clifford Electronics mobile security/convenience system. Clifford Electronics has long been recognized as the leading manufacturer of high-technology vehicle security systems. Our commitment to technological innovation, quality and reliability is clearly evident C in your Clifford system. Yet despite all its sophistication, your system is amazingly easy to use, never more d
ملخص المحتوى في الصفحة رقم 4
Add ing new re mote con trols For other drivers, or to control Clifford G4 systems on your other cars with the same remote, you can buy additional remote controls from any Clifford Dealer (or direct from the Customer Service Department of your nearest Clifford Headquarters listed on the front cover) and program them into the system yourself. Polaris 4 will respond to as many as four remote controls. NOTE: Clifford G4 systems will re spond only to G4-type ACG 2 re mote con trols. Older Clif f
ملخص المحتوى في الصفحة رقم 5
User- Selectable AutoLock and Aut oUn Lock™ Some vehicles are incompatible with the AutoLock and AutoUnLock features. For your safety and that of your passengers, the doors automatically lock the instant you turn on the ignition. When you turn the ignition off, AutoUnLock automatically unlocks the doors. These are user-selectable features. Plain View 2 Coded Valet Mode All car alarms have a valet mode that turn off the security features. This mode is often used to turn off the alarm if the syste
ملخص المحتوى في الصفحة رقم 6
Smart trunk re lease op tion If you have this option, you may use the button to remotely release the trunk latch. The system’s electronic interlock prevents unintentional activation of the remote trunk release when you drive, or when the system is armed. The Smart Trunk Release feature requires installer programming, so if you have the optional trunk release installed, you may want to verify that it will NOT activate when the system is armed. If it can be activated while armed, causing the a
ملخص المحتوى في الصفحة رقم 7
Smart prior in tru sion at tempt alert If you hear three chirps when you disarm, it means that a trigger or sensor was activated in your absence. When you turn on the ignition, the LED will flash 1-8 times, pause, then repeat the flash cycle 4 more times. Count the flashes in one cycle and refer to the chart above. Multiple- event To tal Re call™ The system’s memory records the identity of the last eight activated or malfunctioning triggers and sensors, which allows your installer to instantly t
ملخص المحتوى في الصفحة رقم 8
a. To select another feature in that same column, repeat step 5 within the next 5 seconds (after 5 seconds, 3 chirps mean you are back to the “Feature Select” position). b. To select a different feature column, go to step 4. c. To exit program mode, turn the ignition off (you’ll hear 3 chirps and the LED will turn off). If driving, just wait 60 seconds and the system will automatically exit program mode. If you make an er ror, just turn off the ig ni tion and start again. Ta ble of User- Selecta
ملخص المحتوى في الصفحة رقم 9
Re set All Fea tures If you wish to reset all the user-selectable features to their normal factory presets, you can do so simply by choosing the Reset all features selection (column 1, row 7) on the Table of User-Selectable Features. If you do so, all features — except the programmed remote controls and your valet code — will be reset to the factory settings that are indicated in BOL D type on the Table of User-Selectable Features. To reset all remote controls, use the Clear all remotes feat
