Audiovox SP-10CD دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

SP-10CD
MODEL SP-10CD
10-DISCCDCHANGER
INSTALLATION MANUAL

ملخص المحتوى في الصفحة رقم 2

PACKINGLIST MAIN UNIT Changer INSTALLATIONPARTS Bracket (L) Bracket (R) Hexagonalboltwithwasher 5MeterDinCable (M5 x 10) 1 pc. 1 pc. 4 pcs. 1 pc. Self-tappingscrew Seals(A) Seals(B) (M5 x 12) 4 pcs. 1 pc. 1 pc. OTHER ACCESSORIES CDMagazine Indexsealsheet InstallationManual Owner'sguide 1 pc. 1 pc. 1 pc. 1 pc. 1

ملخص المحتوى في الصفحة رقم 3

BEFOREINSTALLINGTHEUNIT Transport Lock Screws The mechanism in the CD changer is "locked" into place during shipment by the transportscrews. Besuretoremovethescrewspriortoinstallation. l Caution l After removing the transport lock screws, place the supplied seals (A) over the screw holes. These seals are used to keep dust out of the unit, which could cause a malfunction. InstallationandWiringPrecautions Topreventashort-circuit, 1 l Besuretoturnofftheignitionandremovethenegative(-)batterycable,pr

ملخص المحتوى في الصفحة رقم 4

INSTALLATION Theunitcanbeinstalledhorizontally,verticallyorata45°angle. Thepositionofthebuilt-inanti-vibrationsprings(leftandrightside),must correspond to the mounting position chosen. If the springs are not set correctly for the type of installation chosen, the anti-vibration compensation will not be effective and vibration may cause the disc to skip. CAUTION Aftersettingthebuilt-inanti-vibrationsprings,placethesuppliedSeals(B)overtheholes. Thesesealsareusedtokeepdust,whichcould cause a malfunc

ملخص المحتوى في الصفحة رقم 5

PROCEDUREFORVERTICALINSTALLATION Note If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 3), start with step 2. Set the 4 anti-vibration springs to position "V". Attachbracket(L)andbracket(R)toeachsideoftheunit, 1 2 using the hexagonal bolts with washer base (M5 x 8). NOTE: Use seals (A) to cover unused mounting holes on sides of unit. position "V" Bracket (L) Bracket (R) Hexagonal bolt with washer base (M5 x 8) Determine the mounting loca

ملخص المحتوى في الصفحة رقم 6

PROCEDUREFOR45°ANGLEINSTALLATION Note If the anti-vibration spring position has been changed and verified for 45° angle mounting (as shown on page 3), start with step 2. Set the 4 anti-vibration springs to position "45°". Attachbracket(L)andbracket(R)toeachsideoftheunit, 1 2 using the hexagonal bolts with washer base (M5 x 8). NOTE: Use seals (A) to cover unused mounting holes on sides of unit. position "45°" Bracket (L) Bracket (R) Hexagonal bolt with washer base (M5 x 8) Determine the mounting

ملخص المحتوى في الصفحة رقم 7

DIN cable (8-pin) VEHICLEWIRING Mating 8-pin DIN socket on rear of compatible radio chassis (see note 1 below). Car Stereo with CD Changer Controls CD changer NOTE: 1. Check with your Audiovox car audio dealer to be sure your stereo is directly compatible with this CD changer. 2. Wiring instructions for use with FM Modulator/ Commander Systems are included with the CDC-MC1, CDC-MCR2, P-MC3 and P-MCR4 ac- cessories. 6

ملخص المحتوى في الصفحة رقم 8

©1999AUDIOVOXCORP.,HAUPPAUGE,NY Printed in China 128-5542