ملخص المحتوى في الصفحة رقم 1
JBS Technologies
produces the world's
most innovative and
reliable car alarms,
Creating A
remote starters,
keyless entry systems
Higher Standard
and starter
immobilizers.
JBS Technologies is not
an importing or
distribution company.
Our products are
designed with patented
INSTALLATION GUIDE
technology and
produced in the United
•
States with robotics to
insure flawless
OWNER'S GUIDE
performance and the
highest quality control.
Look for our products
and services on the
world wide web where
you'll
ملخص المحتوى في الصفحة رقم 2
YOUR WARRANTY Here's how your warranty works: JBS Technologies warrants to the original customer, and the original car a limited lifetime warranty. Thank you for purchasing American made Within 12 months of purchase, JBS Technologies will products by JBS Technologies. repair or replace, our option, any defective system at To order additional transmitters or other no charge. After 12 months from date of purchase, accessories, visit our JBS Technologies will, at our option, repair or replace web
ملخص المحتوى في الصفحة رقم 3
WARRANTY VALIDATION CONTENTS PLEASE FILL OUT THIS FORM AND MAIL IT IN TO REGISTER YOUR WARRANTY System Features.......................... 4 System Components........................ 5 Your Name ________________________________________ Required Tools........................... 5 Address ________________________________________ Technical Assistance .................... 5 ________________________________________ Before You Begin....................... 5-6 Email Address _____________________
ملخص المحتوى في الصفحة رقم 4
SYSTEM FEATURES Four-Button Remotely start your car to run the heater or air Extended Range conditioning from an extended distance. Remote Control Keyless Entry Remotely locks and unlocks your power door locks. Trunk Release Remotely opens your trunk with a push of a button. (Optional part #775 required) Remote Programmable Remotely program your vehicle to run 5 to 15 Run Time minutes. 1-800-878-8007 Run Time Lets you check the run time that the unit is Confirmation programmed for. www.jbstech.c
ملخص المحتوى في الصفحة رقم 5
VEHICLES WITH FACTORY SYSTEM COMPONENTS ANTI-THEFT SYSTEMS (CONT.) Your system includes: 1-Installation & Operation Guide 2-Window Clips 1-Main Control Module (E Models Only) Manufacturer Make/ Year Anti-theft 1-Four Button Remote Transmitter 1-Warranty PONITAC BONNIEVILLE 89+ VATS with Slide Protector 1-Warning Sticker 1-(4) Relay Harness with Relays for Under the Hood FIREBIRD 88+ VATS 1-18-Pin Wire Harness 2-Bulldog Window Decals GRAND AM 96-98 PASSLOCK 1 1-Hood Pin Switch 1-Extende
ملخص المحتوى في الصفحة رقم 6
VEHICLES WITH FACTORY BEFORE YOU BEGIN cont. ANTI-THEFT SYSTEMS (CONT.) It is recommended that a carbon monoxide detector be installed in the living area near the location where the vehicle may be garaged. Manufacturer Make/ Year Anti-theft SIERRA 98+ PASSLOCK 2 Since there are many different makes and models of vehicles, look at the wiring chart on our website, www.jbstech.com. SONOMA 98+ PASSLOCK 2 Read this manual thoroughly before starting the installation. SUBURBAN 98+ PASSLOCK 2 You
ملخص المحتوى في الصفحة رقم 7
VEHICLES WITH FACTORY TESTING YOUR WIRES ANTI-THEFT SYSTEMS When testing for a positive or negative voltage, you must use a computer-friendly test light (logic probe) or a volt/ohm meter. Make sure to probe and test each wire before making Manufacturer Make/ Year Anti-theft your connections. MALIBU 97+ PASSLOCK 2 MONTE CARLO 96-99 VATS MONTE CARLO 2000+ PASSLOCK 2 MAKING CONNECTIONS FULL-SIZE PU 98+ PASSLOCK 2 S-10 98+ PASSLOCK 2 NOTE: If it is necessary to cut a factory wire to make a
ملخص المحتوى في الصفحة رقم 8
MAKING CONNECTIONS cont. VEHICLES WITH FACTORY ANTI-THEFT SYSTEMS MAKING END TO END CONNECTIONS Manufacturer Make/ Year Anti-theft FOLLOW THESE INSTRUCTIONS Acura TL 99+ TRANSPONDER 1. When tying two separate wires together at their ends, CL 98+ TRANSPONDER strip back one inch of insulation on both wires and RL 99+ TRANSPONDER separate the strands of wire as shown below. INTEGRA 00 + TRANSPONDER NSX TRANSPONDER AUDI A4 00+ TRANSPONDER A6 00+ TRANSPONDER 2. Twist upper wires toge
ملخص المحتوى في الصفحة رقم 9
HOW TO USE YOUR REMOTE TRANSMITTER LOCATING & MAKING CONNECTIONS BUTTON #1 Starts your vehicle from 400 feet away. (E-Model, up to 800 feet) For wiring charts please visit our website, www.jbstech.com. BUTTON #2 Locks and unlocks your power door locks. CONSTANT POWER (+12V, key in any position including off) BUTTON #3 Pops your trunk Make all connections as close to the ignition switch harness as possible. These wire(s) are in your vehicle’s main ignition harness, usually located BUTTON #4 Shuts
ملخص المحتوى في الصفحة رقم 10
LOCATING & MAKING CONNECTIONS OPERATOR PROGRAMMING INSTRUCTIONS Adding Additional Remotes without a Working Remote Control To program a NEW (Replacement) Remote without a working remote, you will ACCESSORY WIRE(S) THAT POWER THE HEATER/BLOWER MOTOR need to CLEAR the E-PROM first. Follow the steps for CLEARING the E-PROM (+12V in run or on positions) This wire is also in the main ignition are at the BOTTOM of this page. After the unit is cleared, you will need to follow the procedure on Page 13,
ملخص المحتوى في الصفحة رقم 11
OPTIONAL CONNECTIONS LOCATING & MAKING CONNECTIONS TRUNK RELEASE OUTPUT (-) (Optional Part #775 required) BRAKE INPUT (+) Locate the trunk release wire coming from the back of the trunk The brake wire is located on the switch near and above the brake release switch. To determine if your trunk release is tripped by pedal, if you cannot locate this wire at the brake switch, you will a (+) positive or a (-) negative (most trunk release switches are then need to locate a wire at the rear window brak
ملخص المحتوى في الصفحة رقم 12
NEUTRAL SAFETY SWITCH OPTIONAL CONNECTIONS MECHANICAL NEUTRAL SAFETY SWITCH (Rear Wheel Drive Only) “Type C” (continued) When installing a Bulldog remote starter on GM vehicles or Dodge Dakotas built prior to 1996, you must: Use the diagram below to create a circuit that will prevent the remote starter from starting the vehicle unless the key is removed from the ignition switch. PRE-1996 GM REAR WHEEL DRIVES WITH PURPLE CRANK WIRE Optional part #775 required. YELLOW Driver’s Door Switch WHITE G
ملخص المحتوى في الصفحة رقم 13
CONNECTING THE 18-PIN HARNESS OPTIONAL CONNECTIONS & 4-RELAY HARNESS CONNECTING DOOR LOCKS (Optional) CONNECTING “TYPE A LOCKS” •If your vehicle has a “Type A” door locking system, connect the BROWN WITH BLACK STRIPE wire from the 18-pin harness to the door lock wire. Connect the GREEN WITH BLACK STRIPE wire to the unlock wire. See diagram below. CONNECTING “TYPE B LOCKS” • If your vehicle has a “Type B” door locking system, connect the GREEN WITH BLACK STRIPE wire from the 18-pin harness to the
ملخص المحتوى في الصفحة رقم 14
OPTIONAL CONNECTIONS ANTENNA PLACEMENT ANTENNA TESTING: Door Locks For best results, run the antenna (YELLOW WIRE WITH BLACK There are three basic types: TIP from the back of the unit) as high up in the dash and as straight as possible. Do not place the antenna next to any metal parts or the vehicle’s main computer control “Type A” Door Lock Test (Most GMs and some Chryslers) module. Range is up to 400 feet. Probe both of your door lock wires going to the door lock switch usally located in the d
